XJ4Ever.com
PO Box 98393
Atlanta, GA 30359-8393
Info@xj4ever.com


Home - Catalog - How-To's - XJBikes.com Forum


XJ750 Seca and XJ750 Euro MODELS FORK TUBE PARTS:

NOTE: items marked below in red are the parts typically needed when doing a basic fork system rebuild.

A good visual review of the procedures needed for rebuilding the 1981-83 forks can be seen at:

http://xjbikes.com/forums/index.php?threads/18730


And here's the secrets to that funny and unique "oil lock valve assembly" used only on these models, and the proper orientation of all of those special washers:

http://xjbikes.com/forums/index.php?threads/41895


Owners of the 1984 XJ750RL models should follow the XJ900 rebuild procedures:

http://xjbikes.com/forums/index.php?threads/44997

and

http://xjbikes.com/forums/index.php?threads/4067


All XJ750 Seca owners should also wish to note the procedure needed to separate the inner tubes from the lower tubes (the "battering ram" procedure) since these forks also use the slider bushings on the bottom of the chrome tubes as shown on these XJ900 forks:

http://xjbikes.com/forums/index.php?threads/4067


And these incredible 3-D renderings of the inner workings of a forking system gives a great visualization of the internal components (it is based on the 1982-83 XJ650 Maxim forks):

http://xjbikes.com/forums/index.php?threads/29616


FORK TUBE REBUILD KITS:

We now offer both a BASIC FORK REBUILD KIT and PERFORMANCE FOR TUBE REBUILD KITS so that you can get all the typically-needed rebuild parts under one simple part number. Each kit is specifically assembled and correct for your particular model bike. NOTE: fork rebuild kits do not include any of the items used in rebuilding the anti-dive units; a separate kit to rebuild those is available as part HCP22001 and is listed in the anti-dive parts section further below.

- NOTE: the lower tube “dust boots” (sometimes called dust seals) are not included in the basic fork tube rebuild kits, but are available separate and can be found further below.

Basic fork rebuild kit contains at least the following items:
- cap bolt o-rings.
- cap bolt retaining rings.
- standard quality lower fork tube oil seals.
- oil seal retaining clips.
- oil drain screws and gaskets.
- damper rod head piston rings.
- damper rod bolts and crush washers.
- air joint o-rings, cushions, and retainer rings (all except 1984 XJ750RL kits).
- air valve o-rings and valve cores (all except 1984 XJ750RL kits).
- anti-dive housing to fork tube o-rings

HCP20629 Aftermarket fork tubes BASIC FORK REBUILD KIT. For all 1981 XJ750 Seca models. NOTE: the oil seals that are included with this kit are 11mm tall, unlike the short (7mm tall) original oil seals, and thus you will need to discard both the original upper and lower oil seal spacer washers that may still be present in your fork system. One kit does both front tubes. This set does not include the lower fork tube dust boots.
$ 179.95

HCP20629DB Aftermarket fork tubes BASIC FORK REBUILD KIT. For all 1981 XJ750 Seca models. NOTE: the oil seals that are included with this kit are 11mm tall, unlike the short (7mm tall) original oil seals, and thus you will need to discard both the original upper and lower oil seal spacer washers that may still be present in your fork system. One kit does both front tubes. This set includes the lower fork tube dust boots.
$ 217.95


HCP20712 Aftermarket fork tubes BASIC FORK REBUILD KIT. For all 1982-83 XJ750 Seca and XJ750 Euro models. NOTE: the oil seals that are included with this kit are 11mm tall, unlike the short (7mm tall) original oil seals, and thus you will need to discard both the original upper and lower oil seal spacer washers that may still be present in your fork system. One kit does both front tubes. This set does not include the lower fork tube dust boots.
$ 179.95

HCP20712DB Aftermarket fork tubes BASIC FORK REBUILD KIT. For all 1982-83 XJ750 Seca and XJ750 Euro models. NOTE: the oil seals that are included with this kit are 11mm tall, unlike the short (7mm tall) original oil seals, and thus you will need to discard both the original upper and lower oil seal spacer washers that may still be present in your fork system. One kit does both front tubes. This set includes the lower fork tube dust boots.
$ 217.95


HCP20635 Aftermarket fork tubes BASIC FORK REBUILD KIT. Fits 1984 XJ750RL (44X Canadian model) and all 1985-1991 XJ900 F, N, and FN models (without the anti-dive fork system). One kit does both front tubes. This set does not include the lower fork tube dust boots.
$ 109.95

HCP20635DB Aftermarket fork tubes BASIC FORK REBUILD KIT. Fits 1984 XJ750RL (44X Canadian model) and all 1985-1991 XJ900 F, N, and FN models (without the anti-dive fork system). One kit does both front tubes. This set includes the lower fork tube dust boots.
$ 137.95



Performance fork rebuild kit contain all of the basic rebuild kit components, along with:
- performance fork springs and related spring seats and plastic spacers.
- upgraded, high-performance lower fork tube oil seals.
- lower fork tube dust boots.
- air valve core stem tool (all except 1984 XJ750RL kits).

HCP20630 Aftermarket fork tubes PERFORMANCE FORK REBUILD KIT. For all 1981 XJ750 Seca models. One kit does both front tubes. NOTE: the oil seals that are included with this kit are 11mm tall, unlike the short (7mm tall) original oil seals, and thus you will need to discard both the upper and lower oil seal spacer washers that may still be present in your fork system.
$ 389.95

HCP20713 Aftermarket fork tubes PERFORMANCE FORK REBUILD KIT. For all 1982-83 XJ750 Seca and XJ750 Euro models. One kit does both front tubes. NOTE: the oil seals that are included with this kit are 11mm tall, unlike the short (7mm tall) original oil seals, and thus you will need to discard both the upper and lower oil seal spacer washers that may still be present in your fork system.
$ 389.95

HCP20636 Aftermarket fork tubes PERFORMANCE FORK REBUILD KIT. Fits 1984 XJ750RL (44X Canadian model) and all 1985-1991 XJ900 F, N, and FN models (without the anti-dive fork system). One kit does both front tubes.
$ 269.95


Of course, all of the component pieces can be ordered as individual pieces from the selections listed below, as well as non-typical wear items (inner tubes, damper rod piston rings, taper spindles, cap bolts, etc.), as well as the fork oil and specialty tools needed to properly restore or enhance your front suspension performance.



UPPER (INNER) FORK TUBES AND PARTS:

Chrome Inner Fork Tubes:

HCP8533 Aftermarket chrome INNER FORK TUBE, fits left or right side, for all 1981-83 XJ750 Seca and XJ750 Euro models, each. NOTE: due to slight differences in manufacturing techniques used on these reproduction tubes (versus the originals), we highly suggest that XJ models which use the anti-dive front suspension ALWAYS replace both front tubes rather than just a single tube.
$ 299.95

HCP8533SET2 Aftermarket chrome INNER FORK TUBES, set of 2:
$ 489.95



HCP9948 Aftermarket chrome INNER FORK TUBE, fits left or right side, for all XJ750RL, XJ900N, and XJ900FN models. Each:
$ 219.95

HCP9948SET2 Aftermarket chrome INNER FORK TUBES, set of 2:
$ 419.95



Inner Tube Gaiter Boots:

Although not originally used on any XJ-series bikes, these accordion-pleated thick rubber boots fit into the area between the bottom of the steering underbracket and the top of the lower (outer) fork boots, covering and protecting this area from damage, while providing an "old-school" or cafe-racer type look. They are retained to the chrome tube itself (at their top end) via spring clips, and to the top of the lower fork tube via metal screw-clamps.


HCP10941 Aftermarket front fork tube GAITER BOOTS, black pleated rubber boot is the correct length and diameter to fit all of the following models: all XJ550 models, all XJ650 models, and all XJ750 Maxim and Midnight Maxim models, all 1981-83 XJ750 Seca, XJ750 Euro, XJ1100, and XS1100 Special and Midnight Special models. Does not include attaching hardware. Light-duty design has equal spacing between each accordion pleat. Pair:
$ 39.95

HCP10942 Aftermarket front fork tube GAITER BOOTS, royal blue pleated rubber boot is the correct length and diameter to fit all of the following models: all XJ550 models, all XJ650 models, and all XJ750 Maxim and Midnight Maxim models, all 1981-83 XJ750 Seca, XJ750 Euro, XJ1100, and XS1100 Special and Midnight Special models. Does not include attaching hardware. Light-duty design has equal spacing between each accordion pleat. Pair:
$ 39.95

HCP10943 Aftermarket front fork tube GAITER BOOTS, red pleated rubber boot is the correct length and diameter to fit all of the following models: all XJ550 models, all XJ650 models, and all XJ750 Maxim and Midnight Maxim models, all 1981-83 XJ750 Seca, XJ750 Euro, XJ1100, and XS1100 Special and Midnight Special models. Does not include attaching hardware. Light-duty design has equal spacing between each accordion pleat. Pair:
$ 39.95


HCP10938 Aftermarket front fork tube GAITER BOOTS, black pleated rubber boot is the correct length and diameter to fit all of the following models: all XJ550 models, all XJ650 models, and all XJ750 Maxim and Midnight Maxim models, all 1981-83 XJ750 Seca, XJ750 Euro, XJ1100, and XS1100 Special and Midnight Special models. Does not include attaching hardware. Light-duty design has equal spacing between each accordion pleat, and each bellows gets wider as the boot extends from top to bottom. Pair:
$ 39.95

HCP10939 Aftermarket front fork tube GAITER BOOTS, royal blue pleated rubber boot is the correct length and diameter to fit all of the following models: all XJ550 models, all XJ650 models, and all XJ750 Maxim and Midnight Maxim models, all 1981-83 XJ750 Seca, XJ750 Euro, XJ1100, and XS1100 Special and Midnight Special models. Does not include attaching hardware. Light-duty design has equal spacing between each accordion pleat, and each bellows gets wider as the boot extends from top to bottom. Pair:
$ 39.95



HCP11420 Aftermarket fork tube gaiter boot LOWER RETAINING SPRING-CLAMP. Black powdercoated wire-spring type clamp has that old-time look and feel to it. Secure the lower end of the gaiter boot to the top of the lower (outer) fork tube. Fits all XJ-series models. Use 1 per tube, each:
$ 14.95


NOTE: gaiter boots normally do not require any type of retainer at their upper end, as the tight friction fit between the boot opening and the chrome tube prevents migration of the boot. If movement seems to occur, then we recommend the use of thin, black electrical wire ties to cinch the boot flange tightly to the tube.




Inner Tube Top Cover/Cap:

HCP8252 OEM inner fork tube black rubber top CAP, fits either the left or right side tube of the following models: XJ550 all, all XJ650 Euro models, 1980-81 XJ650 Maxim and Midnight Maxim, the 1982 XJ650RJ Seca, and 1981 XJ750 Seca models. Each:
$ discontinued

HCP22882 Aftermarket inner fork tube black rubber top CAP, fits either the left or right side tube of the following models: XJ550 all, all XJ650 Euro models, 1980-81 XJ650 Maxim and Midnight Maxim, the 1982 XJ650RJ Seca, and 1981 XJ750 Seca models. Each:
$ 19.95


HCP8291 OEM inner fork tube top black rubber CAP, fits either the left or right side tube of the following models: all 1982-83 XJ750 Seca and XJ750 Euro models. Each:
$ 29.95

HCP22881 Aftermarket inner fork tube top black rubber CAP, fits either the left or right side tube of the following models: all 1982-83 XJ750 Seca and XJ750 Euro models. Each:
$ 19.95



HCP8289 OEM inner fork tube black rubber top CAP, fits either the left or right side tube of the following models: 1984 FJ600, 1982-83 XJ650 Turbo, XJ750RL, XJ750-D, XJ750-P (24L model), and XJ900RK, RL, N/FN, and F Seca models. NOTE: you can substitute the HCP8287 top cap in place of this one for a upgraded appearance! Each:
$ 28.95

HCP22880 Aftermarket inner fork tube black rubber top CAP, fits either the left or right side tube of the following models: 1984 FJ600, 1982-83 XJ650 Turbo, XJ750RL, XJ750-D, XJ750-P (24L model), and XJ900RK, RL, N/FN, and F Seca models. NOTE: you can substitute the HCP8287 top cap in place of this one for a upgraded appearance! Each:
$ 19.95



Inner Fork Tube Cap Bolts and Related Hardware:

HCP8292 OEM inner fork tube CAP BOLT, fits either side. Used on all 1984 FJ600, XJ700 non-X, XJ750RL, and XJ900RK, RL, and N/FN Seca models. NOTE: these cap bolts require a special inverse-hex tool HCP9238 to properly remove and install. Each:
$ 49.95

HCP9238 Aftermarket fork upper cap bolt REVERSE HEX SOCKET TOOL. This tool allows the easy removal and installation of the "inverted/reversed" hex-drive cap bolt used on the top of the inner fork tubes on all 1984 FJ600, XJ650 Turbo, XJ700 non-X, XJ750-D, XJ750P (37H) model, all XJ900RK, RL, N/FN, and F, and 1982 XZ550R Vision models.
$ 17.95


HCP2323 OEM inner fork tube top cap bolt RETAINING RING, fits either the left or right side tube of the following models: all XJ550 models, all XJ650 Euro models, XJ650 Maxim, Midnight Maxim, and XJ650RJ Seca models, and 1981 XJ750 Seca models. Each:
$ 8.95

HCP20715 Aftermarket inner fork tube top cap bolt RETAINING RING, fits either the left or right side tube of the following models: all XJ550 models, all XJ650 Euro models, XJ650 Maxim, Midnight Maxim, and XJ650RJ Seca models, and 1981 XJ750 Seca models. Each:
$ 5.95


HCP13688 Aftermarket inner fork tube top cap bolt RETAINING RING, fits either the left or right side tube of the following models: all 1982-83 XJ750 Seca and XJ750 Euro models. Each:
$ 7.50


HCP8248 OEM inner fork tube CAP BOLT O-RING, fits either side. Used on all 1981-83 XJ750 Seca and XJ750 Euro models. Each:
$ 2.50

HCP14012 Aftermarket inner fork tube CAP BOLT O-RING, fits either side. Used on all 1981-83 XJ750 Seca and XJ750 Euro models. Each:
$ 1.25


HCP8286 OEM inner fork tube cap bolt O-RING, fits either side. Used on all 1984-85 FJ600, XJ700, XJ750-X, XJ750RL, and XJ900RK, RL, N/FN, and F Seca models. Each:
$ 7.95

HCP20708 Aftermarket inner fork tube cap bolt O-RING, fits either side. Used on all 1984-85 FJ600, XJ700, XJ750-X, XJ750RL, and XJ900RK, RL, N/FN, and F Seca models. Each:
$ 5.95



Inner Tube Fork Springs:

HCP9438 Aftermarket front suspension COIL SPRINGS, one pair does both forks. For all 1981-83 XJ750 Seca and XJ750 Euro models. Front spring spacers are required to be used with these springs and a pair of "thick-wall PVC pipe" spacers are included and you can use them instead of the HCP8284 spacer tube and the HCP8239 spring seats. These plastic spacers will still need to be cut to length. Optionally, you could use a pair of the HCP8239 spring seats (one for each spring) and the fabrication of a 42.80mm long spacer when replacing stock springs…..or you can order the HCP21024 spacers tubes which are already cut to the correct length. Optionally, you can use the HCP8284 spring spacer tube (stock for 1982-83 XJ650 Maxim models) and cut it down to the proper length; one tube will provide enough material to do both springs and fork tubes). NOTE: due to the difference in size of this spring versus stock springs, you will need to use approximately 12 cc's less fork oil (for a total of 297cc's per tube) when installing these springs and using the stock thin-wall metal spacer tubes as recommended above. The use of other type of spacers (thick-wall PVC pipe, for instance) will change this recommended fork oil volume by an unknown amount. NOTE: springs should be installed with the tighter (more-closely spaced together) coils towards the top of the fork tube.
$ 139.95



Inner Fork Tube Spring Spacers, Rebound Springs, Damper Rods, and Spring Seats:

HCP8239 OEM inner fork tube SPRING SEAT, fits either side. Use on all 1981-83 XJ750 Seca and XJ750 Euro models when installing the HCP9438 replacement springs above. Each:
$ 19.95

HCP20994 Aftermarket inner fork tube SPRING SEAT, fits either side. Use on all 1981-83 XJ750 Seca and XJ750 Euro models when installing the HCP9438 replacement springs above. Each:
$ 14.95


HCP8284 OEM inner fork tube SPRING SPACER TUBE, Use on all 1981-83 XJ750 Seca and XJ750 Euro models when installing the HCP9438 replacement springs above; one tube will provide enough material to do both springs and fork tubes.
$ 14.95

HCP21024 Aftermarket inner fork tube SPRING SPACER TUBE, fits either side. Use on all 1981-83 XJ750 Seca and XJ750 Euro models when installing the HCP9438 replacement springs above. Each spacer tube is pre-cut to the correct length for use with the HCP9438 springs; use 1 spacer per tube.
$ 19.95

HCP21024SET2 Aftermarket inner fork tube SPRING SPACER TUBE, fits either side. Set of 2 spacers:
$ 34.95



HCP8246 OEM inner fork tube damper rod PISTON RING, fits either side. Used on all 1981-83 XJ750 Seca models, XJ750 Euro, XJ1100, 1980-81 XS1100 Standard models, and all XS1100 Special and Midnight Special models. Use 1 per fork tube. Each:
$ 29.95

HCP13658 Aftermarket inner fork tube damper rod PISTON RING, fits either side. Used on all 1981-83 XJ750 Seca models, XJ750 Euro, XJ1100, 1980-81 XS1100 Standard models, and all XS1100 Special and Midnight Special models. Use 1 per fork tube. Each:
$ 17.95


HCP13657 Aftermarket inner fork tube damper rod PISTON RING, fits either side. Used on all 1984-85 FJ600, all XJ700, XJ750-X, XJ750RL Canadian (44X model), and XJ900 models. Use 1 per fork tube. Each:
$ 17.95



Inner Fork Tube Oil Lock Valve Parts:

Inner Fork Tube Oil Lock Valve Parts:

HCP24632 Aftermarket inner fork tube oil lock valve white plastic PISTON RING, fits either side. Used on all 1981-83 XJ750 Seca and XJ750 Euro models with anti-dive forking system Use 1 per tube, each:
$ 17.95


HCP19354 Aftermarket inner fork tube oil lock valve SPRING WASHER, fits either side. Used on all 1981-83 XJ750 Seca and XJ750 Euro models with anti-dive forking system. Use 1 per tube, each:
$ 19.95

HCP19353 Aftermarket inner fork tube oil lock valve FLAT WASHER, fits either side. Used on all 1981-83 XJ750 Seca and XJ750 Euro models with anti-dive forking system. Use 1 per tube, each:
$ 16.95


Order of assembly of 1981-83 XJ750R Seca and XJ750 Euro models for the oil lock valve assembly components onto the damper rod:
TOP (HEAD) OF DAMPER ROD
DAMPER ROD REBOUND SPRING
Above fitted thru bottom of inner/upper (chrome) fork tube.
On thinner, lower end of damper rod:
FLAT WASHER (HCP19353)
WAVE WASHER (HCP19354)
THICK TAPERED WASHER (“Collar”), narrower end "up"
OPEN END OF OIL LOCK VALVE with PISTON RING (HCP24632)

https://www.xjbikes.com/forums/threads/doing-the-750-secas-forks-rebuild-now-a-how-to.18730




HCP8344 OEM inner fork tube oil lock valve SPRING WASHER, fits either side. Used on all XJ750RL, XJ750P (37H model), and XJ900RK and RL models. Use 2 per tube, each:
$ discontinued

HCP19355 Aftermarket inner fork tube oil lock valve SPRING WASHER, fits either side. Used on all XJ750RL, XJ750P (37H model), and XJ900RK and RL models. Use 2 per tube, each:
$ 19.95

HCP19356 Aftermarket inner fork tube oil lock valve FLAT WASHER, fits either side. Used on all XJ750RL, XJ750P (37H model), and XJ900RK and RL models. Use 1 per tube, each:
$ 17.95

NOTE: the order of installation for the above washers is as follows (and only applies to bikes with anti-dive front fork systems, i.e. the XJ750RL, XJ750P (37H model), and XJ900RK and RL models):

Order of assembly of 1984 XJ750RL, XJ750P (37H model, and XJ900RK/RL Seca oil lock valve assembly components onto damper rod:
NOTE: the Yamaha factory service manual has an incorrect written description and an incorrect image showing the assembly order of the “oil lock valve” components onto the damper rod, showing the two wave washers being adjacent to each other. The correct assembly sequence --- as shown below --- is for the wave washers to be separated by the flat shim washer:
TOP (HEAD) OF DAMPER ROD
DAMPER ROD REBOUND SPRING
Above fitted thru bottom of inner/upper (chrome) fork tube.
On thinner, lower end of damper rod:
WAVE WASHER (HCP19355) goes onto the damper rod shaft first
FLAT WASHER (HCP19356) goes onto the damper rod shaft next
WAVE WASHER (HCP19355) goes onto the damper rod shaft third
Finally the TAPER SPINDLE (HCP3085) goes on last.



Inner Tube Metal Slider Bushings:

NOTE: the following items (for XJ750 Seca/Euro models) are part #3 in the Haynes 650/750 manual, called a “bush”, and are fitted at the very bottom end of the upper (inner / chrome) fork tube…..and while the image in the Haynes manual for this item seemingly locates it at the top of the inner (chrome) fork tube, in reality they are fitted at the bottom of the chrome tube.


HCP8481 OEM inner fork tube METAL SLIDER BUSHING, fits either left or right tube on the following models: 1983 (only) XJ650 Turbo (with 37mm fork tubes), all 1981-83 XJ750 Seca and Euro models, XJ1100, and all XS1100 Special and Midnight Special models. One slider does one tube. Each:
$ 79.95

HCP8481SET2 OEM inner fork tube METAL SLIDER BUSHINGS, set of 2:
$ 154.95



HCP10702 Aftermarket inner fork tube METAL SLIDER BUSHING, fits either left or right tube on the following models: 1983 (only) XJ650 Turbo (with 37mm fork tubes), all 1981-83 XJ750 Seca and Euro models, XJ1100, and all XS1100 Special and Midnight Special models. One slider does one tube. NOTE: these bushings are a bit thinner than the original bushings, but will fit and perform properly. Each:
$ 39.95

HCP10702SET2 Aftermarket inner fork tube METAL SLIDER BUSHINGS, set of 2:
$ 74.95



HCP10705 Aftermarket inner fork tube METAL SLIDER BUSHING, fits either left or right tube on the following models: XJ750RL (45T Australian model), XJ900RK, RL, and N/FN models. One slider does one tube. Each:
$ 29.95

HCP10705SET2 Aftermarket inner fork tube METAL SLIDER BUSHINGS, set of 2:
$ 57.95



INNER FORK TUBE AIR SYSTEM PARTS:

Air Joint Cushions, O-Rings, and Retainers:

HCP8242 OEM air joint rubber UPPER CUSHION GASKET, fits either side, directly above the air joint. Used on all XJ650 Turbo, 1982 XJ750 Maxim, and XJ750-P (24L) models, XJ750-D, 1984 XJ750RL, and XJ900RK and RL models. Use 1 per tube. Also used on these non-XJ models: 1985-86 FZ750, 1983 XV920J Virago, 1984-85 XV1000 Virago, and 1986-94 XV1100 Virago. Each:
$ 10.95

HCP8242SET2 OEM air joint rubber UPPER CUSHION GASKETS, set of 2:
$ 19.95


HCP15647 Aftermarket air joint rubber UPPER CUSHION GASKET, fits either side, directly above the air joint, and cushions the top of the air joint from the bottom of the crown bracket. Used on all XJ650 Turbo, 1982 XJ750 Maxim, and XJ750-P (24L) models, XJ750-D, 1984 XJ750RL, and XJ900RK and RL models. Use 1 per tube. Also used on these non-XJ models: 1985-86 FZ750, 1983 XV920J Virago, 1984-85 XV1000 Virago, and 1986-94 XV1100 Virago. Each:
$ 7.95

HCP15647SET2 Aftermarket air joint rubber UPPER CUSHION GASKETS, fits either side. Set of two:
$ 14.95



HCP8268 OEM air joint rubber UPPER CUSHION GASKET, fits either side, directly above the air joint. Used on all 1981-83 XJ750 Seca, XJ750 Euro, and 1982 XV920J Virago models. Slightly firmer than original material. Use 1 per tube. Each:
$ discontinued

HCP8268SET2 OEM air joint rubber UPPER CUSHION GASKETS, fits either side. Set of two:
$ discontinued


HCP15652 Aftermarket air joint rubber UPPER CUSHION GASKET, fits either side, directly above the air joint. Used on all 1981-83 XJ750 Seca, XJ750 Euro, and 1982 XV920J Virago models. Slightly firmer than original material. Use 1 per tube. Each:
$ 7.95

HCP15652SET2 Aftermarket air joint rubber UPPER CUSHION GASKETS, fits either side. Set of two:
$ 13.95



HCP8279 OEM inner fork tube air joint INNER O-RING, fits either left or right air joint on the following models: 1981-83 XJ750 Seca, XJ750 Euro, and 1982 XV920J Virago models. Use 2 o-rings per air joint. Each:
$ discontinued

HCP8279SET4 OEM inner fork tube air joint INNER O-RINGS, set of 4:
$ discontinued


HCP14016 Aftermarket inner fork tube air joint INNER O-RING, fits either left or right air joint on the following models: 1981-83 XJ750 Seca, XJ750 Euro, and 1982 XV920J Virago models. Use 2 o-rings per air joint. Each:
$ 9.95

HCP14016SET4 Aftermarket inner fork tube air joint INNER O-RINGS, set of 4:
$ 32.95




HCP8341 OEM inner fork tube air joint INNER O-RING, fits either left or right air joint on the following models: 1983 XJ650 Turbo, XJ750-D, XJ750RL, and XJ900RK and RL models. Uses 2 o-rings per joint. Each:
$ discontinued

HCP8341SET4 OEM inner fork tube air joint INNER O-RINGS, set of 4:
$ discontinued


HCP20701 Aftermarket inner fork tube air joint INNER O-RING, fits either left or right air joint on the following models: 1983 XJ650 Turbo, XJ750-D, XJ750RL, XJ900RK and RL models, and XJ1100 models. Uses 2 o-rings per joint. Each:
$ 8.95

HCP20701SET4 Aftermarket inner fork tube air joint INNER O-RINGS, set of 4:
$ 27.95



HCP8259 OEM inner fork tube air joint RETAINER RING, this narrow, stainless steel wire retainer ring fits in the machined groove on the tube and prevents the air joint from migrating along the tube. Use 1 per tube, fits either left or right air joint on the following models: all 1981-83 XJ750 Seca, XJ750 Euro, and 1982 XV920J Virago models. Each:
$ discontinued

HCP12316 Aftermarket inner fork tube air joint RETAINER RING, this narrow, stainless steel wire retainer ring fits in the machined groove on the tube and prevents the air joint from migrating along the tube. Use 1 per tube, fits either left or right air joint on the following models: all 1981-83 XJ750 Seca, XJ750 Euro, and 1982 XV920J Virago models. Each:
$ 8.95



Air Inflation Valves and O-Rings:

HCP8274 OEM inner fork tube air joint AIR VALVE WITH CAP, comes complete the internal stem core, its o-ring, and chrome cap. Fits the following models: 1982-83 XJ650 Maxim (use 1 per tube), XJ650 Turbo models (use 1 per bike), 1982 XJ750 Maxim (use 1 per bike), XJ750-P (24L model, use 1 per tube), XJ750-D (use 1 per bike), 1983 XJ750 Maxim and Midnight Maxim models (use 1 per tube), and XJ900RK and RL Seca models (use 1 per bike). This valve can also be used on all 1981-83 XJ750 Seca, XJ750 Euro, XJ1100, and all XS1100 Special and Midnight Special models, but it is almost 2mm shorter than the original, and the included protective cap is much smaller than the huge caps used on those models, and due to the length difference, those large original caps will not fit properly on this shorter valve. Each:
$ 57.95

HCP25157 OEM inner fork tube air joint AIR VALVE, comes complete the internal stem core and o-ring. Chrome cap is not included. Use 1 per tube on the following models: 1981-83 XJ750 Seca, XJ750 Euro, and all XS1100 Special and Midnight Special models. Use 1 per bike (on the air joint) on XJ1100 models. Each:
$ 47.95


HCP11890 OEM inner fork tube air joint brass AIR VALVE ONLY, comes complete the internal stem core and its o-ring. The chrome cap is not included. Fits the following models: 1982-83 XJ650 Maxim (use 1 per tube), XJ650 Turbo models (use 1 per bike), 1982 XJ750 Maxim (use 1 per bike), XJ750-P (24L model, use 1 per tube), XJ750-D (use 1 per bike), 1983 XJ750 Maxim and Midnight Maxim models (use 1 per tube), and XJ900RK and RL Seca models (use 1 per bike). This valve can also be used on all 1981-83 XJ750 Seca, XJ750 Euro, XJ1100, and all XS1100 Special and Midnight Special models, but it is almost 2mm shorter than the original, and due to the length difference, the large original caps used on those models will not fit properly on this shorter valve. Each:
$ 39.95

HCP11876 OEM inner fork tube air joint air valve CHROME CAP, ribbed, dome-head style. Correct for all of the following models: 1982-83 XJ650 Maxim (use 1 per tube), XJ650 Turbo models (use 1 per bike), 1982 XJ750 Maxim (use 1 per bike), XJ750-P (24L model, use 1 per tube), XJ750-D (use 1 per bike), 1983 XJ750 Maxim and Midnight Maxim models (use 1 per tube), and XJ900RK and RL Seca models (use 1 per bike). This cap can also be used on all 1981-83 XJ750 Seca, XJ750 Euro, XJ1100, and all XS1100 Special and Midnight Special models, but it is much smaller than the large original caps used on those models. Each:
$ 19.95



HCP8271 OEM inner fork tube air joint Air Valve and Hose O-RING, fits the following models: all 1981-83 XJ750 Seca and XJ750 Euro models, (use 1 per tube), XJ1100 models (use 3 per bike), and all XS1100 Special and Midnight Special models (use 1 per tube). Each:
$ 7.95

HCP14020 Aftermarket inner fork tube air joint Air Valve and Hose O-RING, fits the following models: all 1981-83 XJ750 Seca and XJ750 Euro models, (use 1 per tube), XJ1100 models (use 3 per bike), and all XS1100 Special and Midnight Special models (use 1 per tube). Each:
$ 5.95



HCP9194 Aftermarket fork tube AIR VALVE STEM CORE, internal brass valve core with o-ring exactly replaces leaking and damaged originals on all 1985 FJ600 models, 1982-83 XJ650 Maxim and Turbo models, XJ700-X models, all XJ750 models, the XJ900RK model, and XJ1100 models. If your stem is leaking air, this is the inexpensive way to fix it. Each:
$ 3.95

HCP9194SET2 Aftermarket fork tube AIR VALVE STEM CORES, set of 2:
$ 6.95


HCP9196 Aftermarket AIR VALVE STEM TOOL, handy 4-in-1 tool allows you to properly remove and insert the stem core, and also clean/chase/re-thread the internal and external stem threads.
$ 5.95



INNER FORK TUBE RETAINING HARDWARE:

Crown Bracket Inner Fork Tube Retaining Hardware:

HCP4531 OEM crown bracket fork tube CINCH BOLT, use 1 per side. For the following models: XJ650 Turbo, 1982 XJ750 Maxim, and all 1981-83 XJ750 Seca and XJ750 Euro models. Each:
$ 7.95

HCP4531SET2 OEM crown bracket fork tube CINCH BOLTS, use 1 per side. Pair:
$ 14.95




HCP18011 Aftermarket cinch bolt head protective CAP. Smooth, black plastic cap snaps over the head of the fork tube cinch bolts, giving them a very "modern" look, protecting the head from rust. Fits all OEM or aftermarket bolts with a 12mm hex or socket head. Each:
$ 4.95



Under-bracket Inner Fork Tube Retaining Hardware:

HCP3656 OEM under-bracket fork tube CINCH BOLT, use 2 per side. For the following models: all 1981-83 XJ750 Seca, XJ750 Euro, XJ900RK Seca, all XS1100 Standard, and 1979 XS1100 Special models. Each:
$ 795


HCP2185 OEM under-bracket fork tube cinch bolt LOCK WASHER, use 2 per side, a total of 4 per bracket, on all 1981-83 XJ750 Seca, XJ750 Euro, XJ900RK Seca, XJ1100, all XS1100 Standard, and 1979 XS1100 Special models. Each:
$ 6.95

HCP16209 Aftermarket zinc-plated, alloy steel, under-bracket fork tube cinch bolt LOCK WASHER, use 2 per side, a total of 4 per bracket, on all 1981-83 XJ750 Seca, XJ750 Euro, XJ900RK Seca, XJ1100, all XS1100 Standard, and 1979 XS1100 Special models. Each:
$ 2.95

HCP16100 Aftermarket 18-8 stainless-steel, under-bracket fork tube cinch bolt LOCK WASHER, use 2 per side, a total of 4 per bracket, on all 1981-83 XJ750 Seca, XJ750 Euro, XJ900RK Seca, XJ1100, all XS1100 Standard, and 1979 XS1100 Special models. Each:
$ 3.95

HCP16102 Aftermarket black-oxide coated finish, under-bracket fork tube cinch bolt LOCK WASHER, use 2 per side, a total of 4 per bracket, on all 1981-83 XJ750 Seca, XJ750 Euro, XJ900RK Seca, XJ1100, all XS1100 Standard, and 1979 XS1100 Special models. Each:
$ 3.95



HCP18011 Aftermarket cinch bolt head protective CAP. Smooth, black plastic cap snaps over the head of the fork tube cinch bolts, giving them a very "modern" look, protecting the head from rust. Fits all OEM or aftermarket bolts with a 12mm hex or socket head. Each:
$ 4.95



Steering Stabilizer and Hardware:

HCP4543 OEM rotary steering stabilization DAMPER UNIT. Fitted only to 1983 XJ750 Seca models, this round “shimmy-eliminator” unit is fitted to the underside of the lower steering bracket, and interacts against the forward “finger” of the oil cooler mounting loop bracket which is welded to the front frame gusset……and thus provides a resistance, stiffening, and counteraction to fork movement. Mounts simply via a splined shaft and a retention bolt. NOTE: will not fit 1981-82 models, as they do not have the splined shaft receiver nor have proper locating tab or clearance for this device. Although these units are brand new, they should be filled with the proper viscosity of oil and all of the air should be bled out of them (using the two “center” screws). The recommended fluid to use is 15W or 20W fork oil, although you could use a thinner or thicker weight oil is desired…….just like with the forks themselves, the higher the viscosity, the more “dampening” (or resistance to rotary movement) you will obtain. NOTE: 1983 models could have been fitted with this rotary damper unit pr a more traditional fork-tube mounted “piston” style steering stabilizer. The piston stabilizer is normally seen only on bikes with the larger front fairing (“touring package” option).
$ 299.95

HCP25926 Aftermarket rotary steering stabilization DAMPER UNIT REBUILD KIT[/u]. After all of these years these rotary dampers typically require rebuilding (a cleaning, “oil change” and new seals). Our complete rebuild kits contains both the shaft and housing o-rings, the air bleed screws and their sealing gaskets, and a complete set of the housing cinch screws (buttonhead style) and their lock washers. For all 1983 XJ750 Seca models using the rotary steering damper.
$ 59.95



HCP25897 OEM steering stabilization damper unit MOUNTING BOLT, use1 per damper unit. Fits all 1983 XJ750 Seca models using the rotary steering damper. Requires the use of a lockwasher listed below, each:
$ discontinued


HCP1902 OEM steering stabilization damper unit mounting bolt LOCK WASHER, black oxide-coated alloy steel, used with the bolt above on 1983 XJ750 Seca models using the rotary steering damper. Each:
$ 6.95

HCP916 Aftermarket steering stabilization damper unit mounting bolt LOCK WASHER, bright zinc-plated alloy steel, used with the bolt above on 1983 XJ750 Seca models using the rotary steering damper. Each:
$ 1.95

HCP319 Aftermarket steering stabilization damper unit mounting bolt LOCK WASHER, bright 18-8 stainless steel, used with the bolt above on 1983 XJ750 Seca models using the rotary steering damper. Each:
$ 2.95

HCP321 Aftermarket steering stabilization damper unit mounting bolt LOCK WASHER, black oxide-coated alloy steel, used with the bolt above on 1983 XJ750 Seca models using the rotary steering damper. Each:
$ 1.95



HCP25910 Aftermarket steering stabilization damper unit O-RING, fits over the splined shaft and seals the upper housing. Unit must be dis-assembled for replacement. Fits 1983 XJ750 Seca models using the rotary steering damper. Each:
$ 7.95

HCP25909 Aftermarket steering stabilization damper unit O-RING, fits between the upper and lower housings. Unit must be dis-assembled for replacement. Fits 1983 XJ750 Seca models using the rotary steering damper. Each:
$ 14.95



HCP322 OEM steering stabilization damper oil fill/air bleed SCREW, panhead phillips drive, bright zinc-plated alloy steel. Fits into the upper housing. Use 2 per damper assembly on 1983 XJ750 Seca models using the rotary steering damper. Each:
$ 6.95

HCP918 Aftermarket steering stabilization damper oil fill/air bleed SCREW, panhead phillips drive, bright zinc-plated alloy steel. Fits into the upper housing. Use 2 per damper assembly on 1983 XJ750 Seca models using the rotary steering damper. Each:
$ 1.95

HCP25913 Aftermarket steering stabilization damper oil fill/air bleed SCREW, panhead phillips drive, bright zinc-plated alloy steel, JIS small-head design as original. Fits all 1978 and 1980 XS1100 Standard models. Each:
$ 3.95

HCP1355 Aftermarket steering stabilization damper oil fill/air bleed SCREW, panhead phillips drive, bright 18-8 stainless-steel. Fits all 1978 and 1980 XS1100 Standard models. Each:
$ 2.95


HCP7111 OEM steering stabilization damper oil fill/air bleed screw GASKET, use one per screw. Fits 1983 XJ750 Seca models using the rotary steering damper. Each:
$ 8.95

HCP21320 Aftermarket steering stabilization damper oil fill/air bleed screw GASKET, use one per screw. Fits 1983 XJ750 Seca models using the rotary steering damper. Each:
$ 5.95



HCP1467 OEM steering stabilization damper upper-to-lower housing SCREW, alloy steel, zinc-plated, panhead phillips drive. Use 6 per damper unit on 1983 XJ750 Seca models using the rotary steering damper. Must be used with the HCP25925 internal-tooth lock washer below. Each:
$ 8.95

HCP2746 Aftermarket steering stabilization damper upper-to-lower housing SCREW, alloy steel, zinc-plated, panhead phillips drive. Use 6 per damper unit on 1983 XJ750 Seca models using the rotary steering damper. Must be used with the HCP25925 internal-tooth lock washer below. Each:
$ 2.95

HCP2747 Aftermarket steering stabilization damper upper-to-lower housing SCREW, bright 18-8 stainless steel, zinc-plated, panhead phillips drive. Use 6 per damper unit on 1983 XJ750 Seca models using the rotary steering damper. Must be used with the HCP25925 internal-tooth lock washer below. Each.
$ 3.95

HCP21431 Aftermarket steering stabilization damper upper-to-lower housing SCREW, bright polished 18-8 stainless steel, buttonhead, hex-drive fastener. Use 6 per damper unit on 1983 XJ750 Seca models using the rotary steering damper. Must be used with the HCP25925 internal-tooth lock washer below. Each:
$ 2.95

HCP21432 Aftermarket steering stabilization damper upper-to-lower housing SCREW, black-oxide coated alloy steel, socket head, hex-drive. Use 6 per damper unit on 1983 XJ750 Seca models using the rotary steering damper. Must be used with the HCP25925 internal-tooth lock washer below. Each.
$ 1.95



HCP25925 Aftermarket steering stabilization damper upper-to-lower housing screw LOCK WASHER, 18-8 stainless steel, internal-tooth. Use 6 per damper unit on 1983 XJ750 Seca models using the rotary steering damper. Each:
$ 1.95




LOWER (OUTER) FORK TUBE PARTS:

Dust Wiper Seals:

HCP1839 OEM lower fork tube DUST WIPER SEAL, fits either left or right tube on the following models: all 1981-83 XJ750 Seca and XJ750 Euro models. One seal does one tube. Each:
$ 27.95

HCP21560 Aftermarket lower fork tube DUST WIPER SEAL, fits either left or right tube on the following models: all 1981-83 XJ750 Seca and XJ750 Euro models. One seal does one tube. Each:
$ 21.95



HCP1822 OEM lower fork tube DUST WIPER SEAL, fits either left or right tube on the following models: 1984 XJ750RL Seca (44X Canadian models) and all XJ900RK, RL, F, N, and FN models. One seal does one tube. Each:
$ 22.95

HCP21561 Aftermarket lower fork tube DUST WIPER SEAL, fits either left or right tube on the following models: 1984 XJ750RL Seca (44X Canadian models) and all XJ900RK, RL, F, N, and FN models. One seal does one tube. Each:
$ 17.95



Oil Seals:

NOTE: when installing oil seals, make sure that the area where the seal will fit into is clean, free of any nicks and burrs, and that the lower tube metal slide bushing is fully seated. Oil seals install with the large opening facing down, into the tube, and on most seals, the small cast lettering and numbering on the seal faces upwards.

Seals are designed to be installed with a seal driver of some type, although a properly sized piece of hard plastic tubing, perhaps with a proper sized metal washer on top of the seal to "spread the load", works as well. Always make sure that oil seals are fully seated and not damaged or installed in a crooked or cocked manner.


NOTE: all of the following oil seals are 11mm tall, and their use eliminates the need for both the upper (HCP12948) and the lower (HCP3092) spacer washers as originally used on these models. The original oil seals were 7mm tall, and this required the use of the spacer washers to “shim-up” the original seal to the proper height.

HCP1818 OEM lower fork tube OIL SEALS, fits either left or right tube on the following models: all 1981-83 XJ750 Seca and XJ750 Euro models. These seals are a double-spring design, making them less susceptible to leaking and giving them a longer life. Also fits the following non-XJ models: 1987-2000 XV535 Virago, all 1977-79 XS750 models, 1980-81 XS850 Standards, and 1982 XV920J Virago models. One seal does one tube. Each:
$ 26.95

HCP20648 Aftermarket standard quality lower fork tube OIL SEALS, fits all of the following models: all 1981-83 XJ750 Seca and XJ750 Euro models. Comes packaged as a pair of seals, enough to do both forks. Also fits the following non-XJ models: 1987-2000 XV535 Virago, all 1977-79 XS750 models, 1980-81 XS850 Standards, and 1982 XV920J Virago models
$ 39.95

HCP1720 Aftermarket oem-quality lower fork tube OIL SEALS, fits all of the following models: all 1981-83 XJ750 Seca and XJ750 Euro models. Comes packaged as a pair of seals, enough to do both forks. Also fits the following non-XJ models: 1987-2000 XV535 Virago, all 1977-79 XS750 models, 1980-81 XS850 Standards, and 1982 XV920J Virago models
$ 47.95



HCP1816 OEM lower fork tube OIL SEAL, fits either left or right tube on the following models: 1983 XJ650 Turbo, 1984 XJ750RL Seca (44X Canadian model), XJ750-D, XJ750P (37H model), all XJ900RK, RL, N/FN, and F models, and all XS1100 Standard models. Also fits 1981 XV920RH and 1982 XV920RJ Virago models. One seal does one tube. Each:
$ 33.95

HCP20646 Aftermarket standard quality lower fork tube OIL SEALS, fits all of the following models: 1983 XJ650 Turbo, 1984 XJ750RL (44X Canadian model), XJ750-D, XJ750P (37H model), all XJ900RK, RL, N/FN, and F models, and all XS1100 Standard models. Also fits 1981 XV920RH and 1982 XV920RJ Virago models. Comes packaged as a pair of seals, enough to do both forks.
$ 49.95

HCP1718 Aftermarket premium quality lower fork tube OIL SEALS, fits all of the following models: 1983 XJ650 Turbo, 1984 XJ750RL (44X Canadian model), XJ750-D, XJ750P (37H model), all XJ900RK, RL, N/FN, and F models, and all XS1100 Standard models. Also fits 1981 XV920RH and 1982 XV920RJ Virago models. Comes packaged as a pair of seals, enough to do both forks.
$ 54.95




Oil Seal & Dust Seal Kits:

HCP1723 Aftermarket premium quality lower fork tube BLACK OIL SEALS & DUST WIPER SEALS KIT, fits the following models: 1984 XJ750RL Seca (44X Canadian models) and all XJ900RK, RL, F, N, and FN models. Comes with one pair of both the oil and dust seals, enough to do both forks.
$ 64.95



Oil Seal Retaining Clips:

HCP1829 OEM lower fork tube OIL SEAL RETAINING CLIP, fits either left or right tube on the following models: all 1981-83 XJ750 Seca, XJ750 Euro, and all XS1100 Special and Midnight Special models. One clip does one tube. Highly recommended that these be replaced when replacing your oil seals! NOTE: this replacement clip is a thin-wire design, as opposed to the heavy stamped metal clip used originally, but it will fit and operate properly. Each:
$ 9.95

HCP20718 Aftermarket lower fork tube OIL SEAL RETAINING CLIP, fits either left or right tube on the following models: all 1981-83 XJ750 Seca, XJ750 Euro, and all XS1100 Special and Midnight Special models. One clip does one tube. Highly recommended that these be replaced when replacing your oil seals! NOTE: this replacement clip is a thin-wire design, as opposed to the heavy stamped metal clip used originally, but it will fit and operate properly. Each:
$ 6.95



HCP1828 OEM lower fork tube OIL SEAL RETAINING CLIP, fits either left or right tube on the following models: 1992-98 XJ600 Seca II, 1983 XJ650 Turbo, all XJ700, XJ750-X, XJ750RL (44X Canadian model), XJ750-D, XJ750-P (37H model), all XJ900RK, RL, N/FN, and F models, and 1980-81 XS1100 Standard models. One clip does one tube. Highly recommended that these be replaced when replacing your oil seals! Each:
$ 8.95

HCP20717 Aftermarket lower fork tube OIL SEAL RETAINING CLIP, fits either left or right tube on the following models: 1992-98 XJ600 Seca II, 1983 XJ650 Turbo, all XJ700, XJ750-X, XJ750RL (44X Canadian model), XJ750-D, XJ750-P (37H model), all XJ900RK, RL, N/FN, and F models, and 1980-81 XS1100 Standard models. One clip does one tube. Highly recommended that these be replaced when replacing your oil seals! Each:
$ 6.95



Oil Seal Spacer Washer:

NOTE: both the upper and lower spacer washers are needed when using the original 7mm thick oil seals but are not needed (and should not be used) when using our replacement HCP1818, HCP20648, or HCP1720 oil seals.

HCP12948 Aftermarket lower fork tube OIL SEAL SPACER WASHER, fits either left or right tube on the following models: all 1981-83 XJ750 Seca, XJ750 Euro, and 1980-81 XS1100 Special and Midnight Special models. One washer does one tube. This washer goes above the oil seal. Each:
$ 11.95

HCP12948SET2 Aftermarket lower fork tube OIL SEAL SPACER WASHERS, one pair does both forks.
$ 19.95


HCP3092 OEM lower fork tube OIL SEAL SPACER WASHER, fits either left or right tube on the following models: all 1981-83 XJ750 Seca and XJ750 Euro models. One washer does one tube. This washer goes below the oil seal, and above the metal slider bushing! NOTE: original spacer washers were "cupped" at the outer edges; these replacements are flat, but fit and perform as original. Each:
$ 13.95

HCP3092SET2 OEM lower fork tube OIL SEAL SPACER WASHERS, one pair does both forks.
$ 26.95



HCP3094 OEM lower fork tube OIL SEAL SPACER WASHER, fits either left or right tube on the following models: XJ750RL (44X Canadian model), XJ900RK, RL, N/FN, and F models. One washer does one tube. This washer goes below the oil seal, and above the metal slider bushing! Each:
$ discontinued



Lower Tube Metal Slider Bushings:

NOTE: the following items (for XJ750 Seca/Euro models) are part #24 in the Haynes 650/750 manual, called an “upper bush”, and are fitted at the upper end of the lower (outer) fork tube.


HCP3089 OEM lower fork tube METAL SLIDE BUSHING, fits either left or right lower tube on the following models: all 1981-83 XJ750 Seca and XJ750 Euro models. One slider does one tube. Each:
$ 79.95

HCP3089SET2 Aftermarket lower fork tube METAL SLIDE BUSHINGS, set of 2:
$ 149.95


HCP10711 Aftermarket lower fork tube METAL SLIDE BUSHING, fits either left or right lower tube on the following models: all 1981-83 XJ750 Seca and XJ750 Euro models. One slider does one tube. Each:
$ 49.95

HCP10711SET2 Aftermarket lower fork tube METAL SLIDE BUSHINGS, set of 2:
$ 89.95



HCP4259 OEM lower fork tube METAL SLIDE BUSHING, fits either left or right lower tube on the following models: all XJ750RL (45T Australian model), XJ750P (37H models), all XJ900RK, RL, N/FN, and F models, and all XS1100 Standard models. One slider does one tube. Each:
$ 39.95

HCP4259SET2 OEM lower fork tube METAL SLIDE BUSHINGS, set of 2:
$ 69.95


HCP10709 Aftermarket lower fork tube METAL SLIDE BUSHING, fits either left or right lower tube on the following models: all XJ750RL (45T Australian model), XJ750P (37H model), all XJ900RK, RL, N/FN, and F models, and all XS1100 Standard models. One slider does one tube. Each:
$ 37.95

HCP10709SET2 Aftermarket lower fork tube METAL SLIDE BUSHINGS, set of 2:
$ 59.95



HCP19996 OEM lower fork tube METAL SLIDE BUSHING, fits either left or right lower tube on the following models: all XJ550 Maxim, 1984-85 FJ600, XJ650RJ Seca, 1982 XJ650 Turbo, XJ750P (24L models), XJ750RL (44X Canadian model), and 1983 XJ750 Maxim and Midnight Maxim models. One slider does one tube. Each:
$ 34.95

HCP19996SET2 OEM lower fork tube METAL SLIDE BUSHINGS, set of 2:
$ 64.95


HCP10706 Aftermarket lower fork tube METAL SLIDE BUSHING, fits either left or right lower tube on the following models: all XJ550 Maxim, 1984-85 FJ600, XJ650RJ Seca, 1982 XJ650 Turbo, XJ750P (24L models), XJ750RL (44X Canadian model), and 1983 XJ750 Maxim and Midnight Maxim models. One slider does one tube. Each:
$ 29.95

HCP10706SET2 Aftermarket lower fork tube METAL SLIDE BUSHINGS, set of 2:
$ 57.95



Lower Tube Anti-Dive Unit Parts:

The front fork ANTI-DIVE SYSTEM on these models are almost always in need of a complete, thorough cleaning and rebuild. While many people claim that the anti-dive system is a "useless" feature, the real reason may be that the system is so internally fouled and seized that it simply is not operating, at all!

Anti-dive control units are divided into an "upper" (or "top") section, which is the brake plunger assembly....this upper section is where the brake hose, from the brake caliper, attaches. The brake fluid BLEEDER SCREW and the fluid DRAIN SCREW are located in this upper section, as well as the brake plunger piston unit. The O-RING on the plunger should be replaced during a rebuild procedure, as well as a thorough cleaning and polishing of the piston bore. Additionally, there is a snap-ring that retains the damper plunger piston unit into the housing which should be replaced if it is rusty o deformed. HINT: if this piston unit is seized, the use of the HCP12230 Piston Popper fitting will easily free it up.


The "lower" (or "main") section of the anti-dive unit is the larger damper piston assembly (which is bolted to the fork tube), and which contains the damper piston spring and piston. Under hard braking, the brake fluid pressure forces the brake plunger (in the top "brake plunger assembly" section) to push down on the damper piston and its spring, restricting the flow of fork oil in the fork tubes, thus "stiffening" the fork system temporarily----and reducing the amount of front end "dive" during hard braking. The O-RING on the plunger should be replaced during a rebuild procedure, as well as a thorough cleaning and polishing of the piston bore. And the housing-to-fork tube O-RINGS should also be renewed. The small fluid DRAIN SCREW and it COPPER GASKET is typically replaced, and finally, the lower spring seat O-RING at the very bottom of the lower housing, should be replaced to prevent any leaks.

A great picture of the entire XJ750 Seca or XJ750 Euro anti-dive unit can be seen at:

http://xjbikes.com/forums/index.php?threads/1860


And here's one of the components of the lower damper piston assembly on the XJ750-D, XJ750P Police (37H model), and XJ900RK and RL models anti-dive unit can be seen at:

http://xjbikes.com/forums/index.php?threads/44997


NOTE: if you want to disable your anti-dive system, you will need to remove the hose from the caliper to the anti-dive unit (and replace the caliper end double-depth union bolt with the single-depth union bolt used at the anti-dive unit end of the hose) and block-off the anti-dive fluid port with this plug:

HCP12991 Aftermarket brake system fluid port BLOCK-OFF PLUG, correct size hex-drive set-screw is used to replace a brake hose union bolt when not in use. Use 1 per anti-dive unit.
$ 6.95

or an even more stylish alternative is to use these custom-made BLOCK-OFF PLATES that completely replace the upper section of the anti-dive unit:

HCP22861 Aftermarket anti-dive upper housing BLOCK-OFF PLATE, beautiful machined aluminum cover plates completely replace the upper portion of your anti-dive units, fully disabling their function. Black-anondized covers come complete with mounting screws. Sold in a matched LH/RH set. Fits all XJ750 Seca and XJ750 Euro models using anti-dive forks.
$ 79.95



Anti-Dive Rebuild Kits:

No need to guess what parts you’re going to need…..our complete ANTI-DIVE REBUILD KITS take all the guesswork out by supplying you with all of the parts necessary. Kits contain all of the rubber and plastic seals, boots, o-rings, circlips, washers, standard bleeder screws, drain screws, and hardware need to do a complete and thorough rebuild of these units. Experience how your anti-dive units should actually perform by rebuilding them correctly!

HCP22001 Aftermarket complete ANTI-DIVE REBUILD KIT, contains all of the rebuild items needed to overhaul an anti-dive unit used on XJ750 Seca and XJ750 Euro models. One kit services one anti-dive unit. Each:
$ 99.95

HCP22001SET2 Aftermarket complete ANTI-DIVE REBUILD KITS, two complete rebuild kits, enough to service one bike:
$ 189.95



Anti-Dive Individual Rebuild Components:

All of the following items are part of the Brake Piston Assembly (the smaller top cap section of the entire anti-dive unit). Items are listed “in order of appearance” as you would observe as you take the component pieces apart.:

HCP1775 OEM anti-dive brake piston assembly FLUID BLEEDER SCREW, bright finish, fits all 1981-83 XJ750 Seca, XJ750 Euro, XJ750RL, XJ750P (37H model), and XJ900RK and RL models. Each screw comes with the protective rubber cap. Each:
$ 27.95

HCP1775SET2 OEM anti-dive brake piston assembly FLUID BLEEDER SCREWS, set of 2:
$ 49.95


HCP11783 Aftermarket anti-dive brake piston assembly FLUID BLEEDER SCREW, dark finish, fits all 1981-83 XJ750 Seca, XJ750 Euro, XJ750RL, XJ750P (37H model), and XJ900RK and RL models. Protective rubber cap is not included and must be ordered separate. Each:
$ 19.95

HCP11783SET2 Aftermarket anti-dive brake piston assembly FLUID BLEEDER SCREWS, set of 2:
$ 34.95


HCP24097 Aftermarket anti-dive brake piston assembly FLUID BLEEDER SCREW, bright finish, fits all 1981-83 XJ750 Seca, XJ750 Euro, XJ750RL, XJ750P (37H model), and XJ900RK and RL models. Protective rubber cap is not included and must be ordered separate. Each:
$ 19.95

HCP24097SET2 Aftermarket anti-dive brake piston assembly FLUID BLEEDER SCREWS, set of 2:
$ 34.95



HCP7115 OEM anti-dive brake piston assembly air bleeder valve RUBBER CAP, use 1 per housing on all 1981-83 XJ750 Seca, XJ750 Euro, XJ750RL, XJ750P (37H model), and XJ900RK and RL models, each:
$ discontinued

HCP17790 Aftermarket bleeder screw protective rubber DUST CAP, black, dome-shaped head, no retaining strap, each:
$ 1.95

HCP1640 Aftermarket bleeder screw protective rubber DUST CAP, black, dome-shaped head, with retaining strap, no more losing your caps! Each
$ 2.95



HCP6852 Aftermarket anti-dive brake piston assembly SPEED-BLEEDER SCREW, fits all 1981-83 XJ750 Seca, XJ750 Euro, XJ750RL, XJ750P (37H model), and XJ900RK and RL models. These screws are 1mm longer (on the nipple end) than the original screw, and are made from standard alloy steel. Each screw comes with the protective rubber cap. NOTE: speed bleeder screws require the use of a thread sealant product to perform properly......otherwise, air can and will get sucked in thru the threads when the bleeder screw is loosened during the bleeding process. We recommend the use of our HCP13492, and you use it very sparingly. Do not use teflon tape; brake fluid will degrade it, and then the melted goo will be sucked into the speed bleeder valve and clog it.....game over! Each:
$ 8.95

HCP6852SET2 Aftermarket anti-dive brake piston assembly SPEED-BLEEDER SCREWS, set of 2:
$ 16.95



HCP6853 Aftermarket anti-dive brake piston assembly SPEED-BLEEDER SCREW, fits all 1981-83 XJ750 Seca, XJ750 Euro, XJ750RL, XJ750P (37H model), and XJ900RK and RL models. These screws are 6mm longer (on the nipple end) than the original screw, and are made from stainless steel. Each screw comes with the protective rubber cap. NOTE: speed bleeder screws require the use of a thread sealant product to perform properly......otherwise, air can and will get sucked in thru the threads when the bleeder screw is loosened during the bleeding process. We recommend the use of our HCP13492, and you use it very sparingly. Do not use teflon tape; brake fluid will degrade it, and then the melted goo will be sucked into the speed bleeder valve and clog it.....game over! Each:
$ 15.95

HCP6853SET2 Aftermarket anti-dive brake piston assembly SPEED-BLEEDER SCREWS, set of 2:
$ 29.95

NOTE: speed-bleeders should NEVER be used when first re-filling a "dry" brake system----one where the lines, calipers, or master cylinder has been rebuilt or changed, for example----as the air in the system will compress, and the speed-bleeder valve will prevent fluid from flowing through the system. Always bleed dry systems using standard bleeder screws first, and only then install the speed-bleeders, and re-bleed!


HCP13492 Aftermarket anti-dive brake plunger assembly bleeder screw THREAD SEALANT PASTE, designed to fill and seal the thread cavities and prevent air or fluid leaks. 6ml squeeze tube is enough to do a whole bunch of fittings!
$ 7.95



HCP10555 Aftermarket anti-dive brake piston assembly housing-to-damper assembly housing attaching BOLT, correct black-oxide coated, alloy steel socket head cap screw is used to attach the upper and lower housing to each other. Uses 2 per anti-dive unit on all XJ750 Seca and XJ750 Euro models. Each:
$ 1.25

HCP10555SET2 Aftermarket anti-dive brake piston assembly housing-to-damper assembly housing attaching BOLTS, set of 2:
$ 2.00

HCP10555SET4 Aftermarket anti-dive brake piston assembly housing-to-damper assembly housing attaching BOLTS, set of 4:
$ 3.95



HCP10554 Aftermarket anti-dive brake piston assembly housing-to-damper assembly housing attaching BOLT, bright stainless-steel socket head cap screw is used to attach the upper and lower housing to each other. Uses 2 per anti-dive unit on all XJ750 Seca and XJ750 Euro models. Each:
$ 1.75

HCP10554SET2 Aftermarket anti-dive brake piston assembly housing-to-damper assembly housing attaching BOLTS, set of 2:
$ 2.95

HCP10554SET4 Aftermarket anti-dive brake piston assembly housing-to-damper assembly housing attaching BOLTS, set of 4:
$ 5.00



HCP15904 Aftermarket anti-dive brake piston assembly plunger shaft SHIM WASHER, fits around the plunger shaft and is retained by the HCP15905 circlip. Use 1 per housing on all XJ750 Seca and XJ750 Euro models:
$ 17.95

HCP15904SET2 Aftermarket anti-dive brake piston assembly plunger shaft SHIM WASHERS, set of 2:
$ 29.95



HCP15905 Aftermarket anti-dive brake piston assembly piston shaft SNAP RING, use 1 per housing on all 1981-83 XJ750 Seca and XJ750 Euro models. Each:
$ 4.95

HCP15905SET2 Aftermarket anti-dive brake piston assembly piston shaft SNAP RINGS, set of 2:
$ 7.95



HCP15894 Aftermarket anti-dive brake piston assembly piston shaft O-RING, use 1 per shaft on all 1981-83 XJ750 Seca amd XJ750 Euro models. Each:
$ 4.95

HCP15894SET2 Aftermarket anti-dive brake piston assembly piston shaft O-RINGS, set of 2:
$ 7.95



HCP21322 Aftermarket anti-dive brake piston assembly PLUNGER CAP, molded flexible cap that fits in-between the (upper) brake plunger shaft and the (lower) damper piston shaft. Use 1 per unit on all XJ750 Seca and XJ750 Euro models:
$ 24.95

HCP21322SET2 Aftermarket anti-dive brake piston assembly PLUNGER CAPS, set of 2:
$ 44.95



HCP15902 Aftermarket anti-dive brake piston assembly AIR BLEED SCREW, fits all 1981-83 XJ750 Seca and XJ750 Euro models. Use 1 per unit, black-oxide coated hex-drive set screw as original. Each:
$ 4.95

HCP15902SET2 Aftermarket anti-dive brake piston assembly AIR BLEED SCREWS, set of 2:
$ 7.95



All of the following items are part of the Damper Piston Assembly (the larger section of the entire anti-dive unit). Items are listed “in order of appearance” as you would observe them as you take the component pieces apart, from top to bottom.:

HCP15910 Aftermarket anti-dive damper piston assembly plunger shaft SHIM WASHER, fits around the plunger shaft and is retained by the HCP2909 e-clip. Use 1 per side on all XJ750 Seca and XJ750 Euro models:
$ 14.95

HCP15910SET2 Aftermarket anti-dive damper piston assembly plunger shaft SHIM WASHERS, set of 2:
$ 27.95


HCP905 anti-dive damper piston assembly piston shaft retaining E-CLIP,black-phosphate coated spring steel as original, use 1 per side on all 1981-83 XJ750 Seca and XJ750 Euro models. Each:
$ 4.95

HCP905SET2 Aftermarket Hitachi throttle shaft end retaining E-CLIPS, set of 2:
$ 8.95


HCP2909 Aftermarket anti-dive damper piston assembly piston shaft retaining E-CLIP, type 420 stainless spring steel, use 1 per side on all 1981-83 XJ750 Seca and XJ750 Euro models. Each:
$ 6.95

HCP2909SET2 Aftermarket anti-dive damper piston assembly piston shaft retaining E-CLIPS, set of 2:
$ 12.95




HCP15919 Aftermarket anti-dive damper piston assembly piston shaft O-RING, use 1 per shaft on all 1981-83 XJ750 Seca and XJ750 Euro models. Each:
$ 4.95

HCP15919SET2 Aftermarket anti-dive damper piston assembly piston shaft O-RINGS, set of 2:
$ 8.95



HCP21447 Aftermarket anti-dive damper piston assembly plunger shaft (lower end)-to-piston cup-opening polyurethane (hard plastic) OIL SEAL, used at the lower end of the piston shaft (held onto the shaft via a special shouldered torx-drive screw and a metal collar). Durable polyurethane material as original. Use 1 per housing on all 1981-83 XJ750 Seca and XJ750 Euro models. Each:
$ 22.95

HCP21447SET2 Aftermarket anti-dive damper piston assembly plunger shaft (lower end)-to-piston cup-opening polyurethane (hard plastic) OIL SEALS, set of 2:
$ 41.95



HCP21522 Aftermarket anti-dive damper piston assembly piston spring RETAINING WIRE CLIP, retains the large spring in the lower section of the housing, use 1 per side on all 1981-83 XJ750 Seca and XJ750 Euro models. Each:
$ 12.95

HCP21522SET2 Aftermarket anti-dive damper piston assembly piston spring RETAINING WIRE CLIPS, set of 2:
$ 22.95




HCP15882 OEM anti-dive damper piston assembly FLUID DRAIN SCREW, fits all 1981-83 XJ750 Seca and XJ750 Euro models. Use 1 per unit, phosphate-coated phillips-drive screw as original. Includes the copper gasket. Each:
$ 9.95

HCP6708 Aftermarket anti-dive damper piston assembly FLUID DRAIN SCREW, fits all 1981-83 XJ750 Seca and XJ750 Euro models. Use 1 per unit, panhead phillips-drive zinc-plated alloy steel. Each:
$ 1.95

HCP6709 Aftermarket anti-dive damper piston assembly FLUID DRAIN SCREW, fits all 1981-83 XJ750 Seca and XJ750 Euro models. Use 1 per unit, panhead phillips-drive 18-8 stainless steel, bright finish. Each:
$ 2.95

HCP6710 Aftermarket anti-dive damper piston assembly FLUID DRAIN SCREW, fits all 1981-83 XJ750 Seca and XJ750 Euro models. Use 1 per unit, panhead phillips-drive 18-8 stainless steel, black-oxide coated finish. Each:
$ 1.95

HCP6712 Aftermarket anti-dive damper piston assembly FLUID DRAIN SCREW, fits all 1981-83 XJ750 Seca and XJ750 Euro models. Use 1 per unit, socket head cap screw, hex-drive, 18-8 stainless steel, bright finish. Each:
$ 2.95

HCP6711 Aftermarket anti-dive damper piston assembly FLUID DRAIN SCREW, fits all 1981-83 XJ750 Seca and XJ750 Euro models. Use 1 per unit, socket head cap screw, hex-drive, black-oxide coated finish. Each:
$ 1.95




HCP15891 Aftermarket anti-dive damper piston assembly fluid drain screw COPPER GASKET, fits all 1981-83 XJ750 Seca and XJ750 Euro models. Use 1 per unit, this is the copper gasket only. Each:
$ 4.95

HCP15891SET2 Aftermarket anti-dive damper piston assembly fluid drain screw COPPER GASKETS, set of 2:
$ 8.95


HCP10556 Aftermarket anti-dive damper piston assembly housing-to-fork tube attaching BOLT, correct black-oxide coated, alloy steel socket head cap screw is used to attach the main housing to the lower fork tube. Uses 4 per side on all 1981-83 XJ750 Seca and XJ750 Euro models. Each:
$ 2.95

HCP10556SET4 Aftermarket anti-dive damper piston assembly housing-to-fork tube attaching BOLTS, set of 4:
$ 10.95

HCP10556SET8 Aftermarket anti-dive damper piston assembly housing-to-fork tube attaching BOLTS, set of 8:
$ 17.95



HCP10558 Aftermarket anti-dive damper piston assembly housing-to-fork tube attaching O-RING, used where the main housing attaches to the lower fork tube. Uses 2 per housing on all 1981-83 XJ750 Seca and XJ750 Euro models. Each:
$ 4.95

HCP10558SET2 Aftermarket anti-dive damper piston assembly housing-to-fork tube attaching O-RINGS, set of 2:
$ 8.95

HCP10558SET4 Aftermarket anti-dive damper piston assembly housing-to-fork tube attaching O-RINGS, set of 4:
$ 17.95



HCP15890 Aftermarket anti-dive damper piston assembly lower spring seat (adjuster screw) housing O-RING, used where the adjuster screw assembly attaches to the very bottom damper piston assembly housing. Durable Buna-N material as original. Use 1 per housing on all 1981-83 XJ750 Seca and XJ750 Euro models. Each:
$ 5.95

HCP15890SET2 Aftermarket anti-dive damper piston assembly lower spring seat (adjuster screw) housing O-RINGS, set of 2:
$ 9.95



HCP15981 Aftermarket anti-dive damper piston assembly lower spring seat (adjuster screw) housing O-RING, used where the adjuster screw assembly attaches to the very bottom damper piston assembly housing. Premium Viton material is more durable than original. Use 1 per housing on all 1981-83 XJ750 Seca and XJ750 Euro models. Each:
$ 8.95

HCP15981SET2 Aftermarket anti-dive damper piston assembly lower spring seat (adjuster screw) housing O-RINGS, set of 2:
$ 16.95



HCP21326 Aftermarket anti-dive damper piston assembly adjuster screw RUBBER CAP, covers and protects the adjuster screw at the very bottom damper piston assembly housing. Use 1 per housing on all 1981-83 XJ750 Seca and XJ750 Euro models. Each:
$ 22.95

HCP21326SET2 Aftermarket anti-dive damper piston assembly adjuster screw RUBBER CAPS, set of 2:
$ 39.95



Lower Fork Tube Oil Drain Screw and Gasket:

HCP5187 OEM lower fork tube oil DRAIN SCREW, use one per tube. Panhead, phillips-drive, alloy steel with a black finish. Note that the black screw was used on models with black lower fork tubes (1982-83 XJ550 Seca, FJ600, 1995 XJ600 Seca II, XJ650 Midnight Maxim, XJ650 Turbo, XJ750 Midnight Maxim, 1981-83 XJ750 Seca and XJ750 Euro models, and some XJ750P models 37H). All other models with natural aluminum lower fork tubes used a screw with a bright finish. Fits all XJ-series bikes (except XJ1100 models), all XS1100 Standards, 1988-90 FZR400, and 1982-83 XZ550R Vision models. Each:
$ 4.95

HCP29817 Aftermarket lower fork tube oil DRAIN SCREW, use one per tube, panhead, phillips-drive, alloy steel with a black-oxide coated finish. Fits all XJ-series bikes (except XJ1100 models), all XS1100 Standards, 1988-90 FZR400, and 1982-83 XZ550R Vision models. Each:
$ 1.95

HCP29005 Aftermarket lower fork tube oil DRAIN SCREW, use one per tube, panhead phillips-drive zinc-plated alloy steel. Fits all XJ-series bikes (except XJ1100 models), all XS1100 Standards, 1988-90 FZR400, and 1982-83 XZ550R Vision models. Each:
$ 1.95

HCP29006 Aftermarket lower fork tube oil DRAIN SCREW, use one per tube, panhead phillips-drive 18-8 stainless steel, bright finish. Fits all XJ-series bikes (except XJ1100 models), all XS1100 Standards, 1988-90 FZR400, and 1982-83 XZ550R Vision models. Each:
$ 2.95

HCP6710 Aftermarket lower fork tube oil DRAIN SCREW, use one per tube, panhead phillips-drive 18-8 stainless steel, black-oxide coated finish. Fits all XJ-series bikes (except XJ1100 models), all XS1100 Standards, 1988-90 FZR400, and 1982-83 XZ550R Vision models. Each:
$ discontinued

HCP6712 Aftermarket lower fork tube oil DRAIN SCREW, use one per tube, socket head cap screw, hex-drive, 18-8 stainless steel, bright finish. Fits all XJ-series bikes (except XJ1100 models), all XS1100 Standards, 1988-90 FZR400, and 1982-83 XZ550R Vision models. Each:
$ 2.95

HCP6711 Aftermarket lower fork tube oil DRAIN SCREW, use one per tube, socket head cap screw, hex-drive, black-oxide coated finish. Fits all XJ-series bikes (except XJ1100 models), all XS1100 Standards, 1988-90 FZR400, and 1982-83 XZ550R Vision models. Each:
$ 1.95



HCP7111 OEM lower fork tube oil drain screw GASKET, use one per tube. Fits all XJ-series bikes (except XJ1100 models), all XS1100 Standards, 1988-90 FZR400, and 1982-83 XZ550R Vision models. Each:
$ 8.95

HCP7111SET2 OEM lower fork tube oil drain screw GASKET, use one per tube. Fits all XJ-series bikes (except XJ1100 models), all XS1100 Standards, 1988-90 FZR400, and 1982-83 XZ550R Vision models. Each. Per pair:
$ 16.95


HCP21320 Aftermarket lower fork tube oil drain screw GASKET, use one per tube. Fits all XJ-series bikes (except XJ1100 models), all XS1100 Standards, 1988-90 FZR400, and 1982-83 XZ550R Vision models. Each:
$ 5.95

HCP21320SET2 Aftermarket lower fork tube oil drain screw GASKET, use one per tube. Fits all XJ-series bikes (except XJ1100 models), all XS1100 Standards, 1988-90 FZR400, and 1982-83 XZ550R Vision models. Each. Per pair:
$ 10.95



Lower Fork Tube Damper Rod Retaining Bolt and Gasket:

HCP8233 OEM fork tube damper rod RETAINING SCREW. For all XJ550, 1984-85 FJ600, 1992-98 XJ600 Seca II, XJ650, XJ700, XJ750 (except 1981-83 XJ750 Seca or XJ750 Euro), XJ750RL, XJ900, all XS1100 Standards, 1988-90 FZR400, and 1982-83 XZ550R Vision models. Use 1 per tube. Each:
$ 9.95

HCP28069 Aftermarket fork tube damper rod RETAINING SCREW. For all XJ550, 1984-85 FJ600, 1992-98 XJ600 Seca II, XJ650, XJ700, XJ750 (except 1981-83 XJ750 Seca or XJ750 Euro), XJ750RL, XJ900, all XS1100 Standards, 1988-90 FZR400, and 1982-83 XZ550R Vision models. Use 1 per tube. Each:
$ 6.95


HCP8234 OEM fork tube damper rod retaining screw copper crush washer GASKET. For all XJ550, 1984-85 FJ600, 1992-98 XJ600 Seca II, XJ650, XJ700, XJ750 (except 1981-83 XJ750 Seca or XJ750 Euro), XJ750RL, XJ900, all XS1100 Standards, 1988-90 FZR400, and 1982-83 XZ550R Vision models. Use 1 per tube. Each:
$ 16.95

HCP12950 Aftermarket fork tube damper rod retaining screw copper crush washer GASKET. For all XJ550, 1984-85 FJ600, 1992-98 XJ600 Seca II, XJ650, XJ700, XJ750 (except 1981-83 XJ750 Seca or XJ750 Euro), XJ750RL, XJ900, all XS1100 Standards, 1988-90 FZR400, and 1982-83 XZ550R Vision models. Use 1 per tube. Each:
$ 10.95



HCP8281 OEM fork tube damper rod RETAINING SCREW. For all 1981-83 XJ750 Seca, XJ750 Euro, XJ1100, and all XS1100 Special and Midnight Special models. Use 1 per tube. Comes with the copper crush washer "gasket". Each:
$ 11.95

HCP22133 Aftermarket fork tube damper rod RETAINING SCREW. For all 1981-83 XJ750 Seca, XJ750 Euro, XJ1100, and all XS1100 Special and Midnight Special models. Use 1 per tube. Gasket is not included. Each:
$ 4.95

HCP10028 Aftermarket fork tube damper rod retaining screw copper crush washer GASKET. For all 1981-83 XJ750 Seca, XJ750 Euro, XJ1100, and all XS1100 Special and Midnight Special models. Use 1 per tube. Each:
$ 4.95



w) Lower Fork Tube DAMPER ROD RETAINING TOOL. This long aluminum tool, with proper sized nuts on each end, is used to retain the top of the fork damper rod (in the bottom of the chrome tube) when removing or installing the damper rod retaining screw. One end has a 19mm hex and the other end has a 22mm hex, so it will fit all styles of XJ-series bikes except XJ600 Seca II, 1981-83 XJ750 Seca, XJ1100, and all XS1100 Special and Midnight Special models. This tool will make the disassembly of your upper tube from the lower tube much easier! NOTE: this tool is available for short term rental, please see the “rental” section within the THE TOOLBOX section of our catalog at:

http://xjbikes.com/forums/index.php?threads/xj-parts-catalog-section-p-the-toolbox.44630

and review the availability and procedures in the TOOL RENTAL section.


NOTE: the HCP4402 tool does not work with certain forks (the XJ750 Seca being one of them) since the head of the damper rod does not have the internal fluting which the damper rod tool would catch onto (thus locking the damper rod in place, allowing the bolt to be removed). Instead, the damper rod is held via the insertion of a thin, round object (allen wrench of a phillips-drive screwdriver shaft) thru the lower hole in the lower fork tube where the anti-dive housings attach to the lower fork tube. This tool will go thru a drilled hole in the damper rod, thus locking it in place (preventing rotation).

You can see a good image of this about half-way down the page (during the re-assembly process, although, it will probably also be necessary during the dis-assembly process) on the following page:

https://www.xjbikes.com/forums/threads/doing-the-750-secas-forks-rebuild-now-a-how-to.18730


HCP4402 Aftermarket DAMPER ROD RETAINING TOOL, for use on 1984 XJ750RL models (without anti-dive system). Note that all XJ750 Seca models (and XJ750 Euro models) with anti-dive systems do not need nor use this tool.
$ 37.95




Lower Fork Tube Speedometer Cable Hardware:

HCP2182 OEM lower fork tube speedometer cable bracket mounting BOLT, 6-point hex head alloy steel fastener with a bright finish, on the left fork tube only, use 1 on all XJ550 Maxim, XJ650 Maxim, XJ750 Maxim, 1981 XJ750 Seca, XJ1100, and XS1100 Standard and Special models. Bright plating. Use with the HCP315, HCP916, or HCP319 lock washer below. Each:
$ 6.95

HCP22180 Aftermarket lower fork tube speedometer cable bracket mounting BOLT, 6-point hex head alloy steel fastener with a dark finish, on the left fork tube only, use 1 on all XJ550 Maxim, XJ650 Maxim, XJ750 Maxim, 1981 XJ750 Seca, XJ1100, and XS1100 Standard and Special models. Bright plating. Use with the HCP315, HCP916, or HCP319 lock washer below. Each:
$ 1.95

HCP22182 Aftermarket lower fork tube speedometer cable bracket mounting BOLT, 6-point hex head 18/8 stainless steel fastener with a bright finish, on the left fork tube only, use 1 on all XJ550 Maxim, XJ650 Maxim, XJ750 Maxim, 1981 XJ750 Seca, XJ1100, and XS1100 Standard and Special models. Bright plating. Use with the HCP315, HCP916, or HCP319 lock washer below. Each:
$ 2.95

HCP22183 Aftermarket lower fork tube speedometer cable bracket mounting BOLT, 6-point hex head 316 stainless steel fastener with a bright finish, on the left fork tube only, use 1 on all XJ550 Maxim, XJ650 Maxim, XJ750 Maxim, 1981 XJ750 Seca, XJ1100, and XS1100 Standard and Special models. Bright plating. Use with the HCP315, HCP916, or HCP319 lock washer below. Each:
$ 3.95

HCP22181 Aftermarket lower fork tube speedometer cable bracket mounting BOLT, 6-point hex head alloy steel fastener has a serrated flange (which eliminates the need for using a lockwasher) and features a dark finish, on the left fork tube only, use 1 on all XJ550 Maxim, XJ650 Maxim, XJ750 Maxim, 1981 XJ750 Seca, XJ1100, and XS1100 Standard and Special models. Bright plating. Use with the HCP315, HCP916, or HCP319 lock washer below. Each:
$ 2.95


HCP3933 OEM lower fork tube speedometer cable bracket mounting BOLT, 6-point hex head alloy steel fastener with a dark finish, on the left fork tube only, use 1 on all XJ650 Midnight Maxim, XJ750 Midnight Maxim, 1982-83 XJ750 Seca, XJ750 Euro, and XS1100 Midnight Special models. Use with the HCP1902 or the HCP321 lock washer below. Each:
$ 3.95

HCP22180 Aftermarket lower fork tube speedometer cable bracket mounting BOLT, 6-point hex head alloy steel fastener with a dark finish, on the left fork tube only, use 1 on all XJ650 Midnight Maxim, XJ750 Midnight Maxim, 1982-83 XJ750 Seca, XJ750 Euro, and XS1100 Midnight Special models. Use with the HCP1902 or the HCP321 lock washer below. Each:
$ 1.95

HCP22182 Aftermarket lower fork tube speedometer cable bracket mounting BOLT, 6-point hex head 18/8 stainless steel fastener with a bright finish, on the left fork tube only, use 1 on all XJ650 Midnight Maxim, XJ750 Midnight Maxim, 1982-83 XJ750 Seca, XJ750 Euro, and XS1100 Midnight Special models. Use with the HCP1902 or the HCP321 lock washer below. Each:
$ 2.95

HCP22183 Aftermarket lower fork tube speedometer cable bracket mounting BOLT, 6-point hex head 316 stainless steel fastener with a bright finish, on the left fork tube only, use 1 on all XJ650 Midnight Maxim, XJ750 Midnight Maxim, 1982-83 XJ750 Seca, XJ750 Euro, and XS1100 Midnight Special models. Use with the HCP1902 or the HCP321 lock washer below. Each.
$ 3.95

HCP22181 Aftermarket lower fork tube speedometer cable bracket mounting BOLT, 6-point hex head alloy steel fastener has a serrated flange (which eliminates the need for using a lockwasher) and features a dark finish. Fitted on the left fork tube only, use 1 on all XJ650 Midnight Maxim, XJ750 Midnight Maxim, 1982-83 XJ750 Seca, XJ750 Euro, and XS1100 Midnight Special models. Use with the HCP1902 or the HCP321 lock washer below. Each.
$ 2.95



HCP315 OEM lower fork tube speedometer cable bracket mounting bolt LOCK WASHER, bright finish, use 1 per bike on the following models: all XJ550 Maxim models, all XJ650 Maxim and Midnight Maxim models, all XJ750 Maxim models, 1981 XJ750 Seca models, XJ1100, and XS1100 models.
$ 3.95

HCP1902 OEM lower fork tube speedometer cable bracket mounting bolt LOCK WASHER, black finish, use 1 per bike on the following models: XJ650 Midnight Maxim, 1982-83 XJ750 Seca, XJ750 Euro, XJ750 Midnight Maxim, and XS1100 Midnight Special models.
$ 6.95

HCP916 Aftermarket zinc-plated alloy steel with a natural finish, lower fork tube speedometer cable bracket mounting bolt LOCK WASHER, use 1 per bike on the following models: all XJ550 Maxim models, all XJ650 Maxim and Midnight Maxim models, all XJ750 Maxim models, 1981 XJ750 Seca models, XJ1100, and XS1100 models:
$ 1.95

HCP319 Aftermarket 18-8 stainless steel lower fork tube speedometer cable bracket mounting bolt LOCK WASHER, use 1 per bike on the following models: all XJ550 Maxim models, all XJ650 Maxim and Midnight Maxim models, all XJ750 Maxim models, 1981 XJ750 Seca models, XJ1100, and XS1100 models:
$ 2.95

HCP321 Aftermarket black oxide-coated alloy steel lower fork tube speedometer cable bracket mounting bolt LOCK WASHER, use 1 per bike on the following models: all XJ550 Maxim models, all XJ650 Maxim and Midnight Maxim models, all XJ750 Maxim models, 1981 XJ750 Seca models, XJ1100, and XS1100 models:
$ 1.95




Fork Tube Brace and Hardware:

HCP8480 OEM lower fork tube brace RETAINING BOLT, use 2 per tube (4 per bike) on both the left and right side lower fork tube. Bright finish, alloy steel socket head, allen-drive. For all FJ600, XJ750RL, and XJ900RK, RL, N/FN, and F models. Each:
$ 2.95

HCP2424 Aftermarket lower fork tube brace RETAINING BOLT, use 2 per tube (4 per bike) on both the left and right side lower fork tube. Black oxide coated alloy steel socket head, allen-drive. For all FJ600, XJ750RL, and XJ900RK, RL, N/FN, and F models. Each:
$ 1.95

HCP80 Aftermarket lower fork tube brace RETAINING BOLT, use 2 per tube (4 per bike) on both the left and right side lower fork tube. Black oxide coated alloy steel socket head, allen-drive. Features a small nylon thread patch, making this a self-locking bolt. For all FJ600, XJ750RL, and XJ900RK, RL, N/FN, and F models. Each:
$ 2.95

HCP2423 Aftermarket lower fork tube brace RETAINING BOLT, use 2 per tube (4 per bike) on both the left and right side lower fork tube. Bright 18-8 stainless steel socket head, allen-drive. For all FJ600, XJ750RL, and XJ900RK, RL, N/FN, and F models. Each:
$ 2.95



Lower Fork Tube Axle Retaining Hardware:

HCP4828 OEM front axle shaft-to-lower tube RETAINING BOLT, use 1 per tube (2 per bike) on both the left and right side lower fork tube. For all XJ550 Seca, 1984-85 FJ600, all XJ650 Euro models, XJ650RJ Seca and XJ650 Turbo models, XJ750RL, XJ750P (37H model), and XJ900RK, RL, N/FN, and F models. Each:
$ 8.95

HCP4824 OEM front axle shaft-to-lower tube retaining bolt LOCK WASHER, use 1 per bike on the following models: all 1981-83 XJ750 Seca and XJ750 Euro models. Each:
$ 9.95

HCP16102 Aftermarket front axle shaft-to-lower tube retaining bolt LOCK WASHER, black-oxide coated finish, use 1 per bike on the following models: all 1981-83 XJ750 Seca and XJ750 Euro models. Each:
$ 3.95


HCP3494 OEM front axle shaft-to-lower tube retaining bolt NUT, use 1 per bike on the following models: all XJ550 Maxim models, all XJ650 (except Midnight Maxim) models, all XJ700 non-X models, all 1982-83 XJ750 Maxim, XJ750-D, and XJ1100 models. Use 2 per bike on the following models: all XJ550 Seca, 1984-85 FJ600, all XJ650 Euro models, XJ750RL, all XJ900RK, RL, N/FN, and F models, and 1979 XS1100 Special models. Each:
$ 3.95

HCP24037 Aftermarket front axle shaft-to-lower tube retaining bolt NUT, made from 18/8 stainless steel, use 1 per bike on the following models: all XJ550 Maxim models, all XJ650 (except Midnight Maxim) models, all XJ700 non-X models, all 1982-83 XJ750 Maxim, XJ750-D, and XJ1100 models. Use 2 per bike on the following models: all XJ550 Seca, 1984-85 FJ600, all XJ650 Euro models, XJ750RL, all XJ900RK, RL, N/FN, and F models, and 1979 XS1100 Special models. Each:
$ 2.95



Lower Tube ID Decals:

HCP15136 Aftermarket AIR SUSPENSION WARNING DECAL, this rectangular decal has a black background with silver lettering and border. Correct for all 1981-83 XJ750 Seca and XJ750 Euro models. It mounts on the left lower fork tube almost directly in line with the caliper mounting bosses, and faces “outward”.
$ 12.95



FORK SYSTEM SERVICE TOOLS:

Assembly and Dis-assembly Tools:

NOTE: many of these tools are available for short term rental, please see the “rental” section within the THE TOOLBOX section of our catalog at:

http://xjbikes.com/forums/index.php?threads/xj-parts-catalog-section-p-the-toolbox.44630

and review the availability and procedures in the TOOL RENTAL section.


HCP4402 Aftermarket DAMPER ROD RETAINING TOOL, for use on 1984 XJ750RL models (without anti-dive system). Note that all XJ750 Seca models (and XJ750 Euro models) with anti-dive systems do not need nor use this tool.
$ 37.95


HCP26093 Aftermarket lower fork tube OIL SEAL DRIVER. split “clamshell” heavy duty design allows it to be used properly and safely install the lower tube oil seals and (where applicable) lower tube dust seals on all 35-36mm fork tubes (XJ550 Seca, FJ600, XJ600 Euro, all XJ650 (except 1983 Turbo), all XJ750 air-cooled (except XJ750P (37H Police) and X750-D models), and XJ900 N/FN models).
$ 39.95



Super-Penetrant Fluids and Lubricants:

Sometimes, the toughest part of working on a vehicle is battling the effects of time: seized fasteners, caused by rust, corrosion, and other factors, turns what should be a 5-minute effort into a 50-minute (or more) chore, complete with rounded-off, ruined, or snapped fasteners, e-z outs, heli-coil inserts, and more.........and that's just not right.

While the proper use of our various Anti-Seize products will prevent these nightmares from occurring in the future, you're stuck in the here-and-now, and the best way to handle these obstacles is to have the proper tools at the stand-by; and in the case of fastener seizure, the proper "tool" is a can or two of our SUPER PENETRATING LUBRICANTS at the ready; a couple of squirts, a little bit of time-----perhaps some heat for those really nasty situations----and you're on your way again, hopefully not too much worse for the experience.....

Great for use on all fasteners, fork tube cap bolts, intake and exhaust manifolds bolts, studs, and nuts, lock cylinder tumblers, or anywhere an un-cooperative fastener can be found. Can even be used to help un-seize frozen engines!

Be aware that these products are not your typical, garden-variety, run-of-the-mill "retail" type products; these are designed an used as industrial- and military-strength products, meaning they have special formulations that include a dollop more of the "good stuff" within them to solve the toughest seizure problems imaginable (the "good stuff" ingredients cost more, and it is those compounds that are left out of or reduced in concentration in "retail" level consumer products).

NOTE: the following product(s) can only be shipped via ground transport (which thus eliminates the postal Priority Mail, postal Express Mail, or private carrier Expedited levels of service for this item) and cannot (and will not----don't even ask!) be shipped outside of the continental USA. Additionally, there may be a per-package weight or quantity restriction, and thus multiple-unit orders of this product may have to be shipped in separate packages and will incur additional shipping charges.

HCP10331 Aftermarket standard-duty PENETRATING LUBRICANT, in a generous 16-ounce aerosol can. Oil-based lubricant penetrates down into spaces of one-millionth of an inch to handle the most reluctant seizures. Actually dissolves the rust and corrosion that causes the seizure; lubricates and displaces moisture to prevent rust re-formation. This product is what we use and recommend for freeing stuck fork tube cap bolts and other such challenging fasteners.
$ 44.95

HCP11974 Aftermarket super-duty PENETRATING LUBRICANT, in a generous 13-ounce aerosol can. Same as our standard-duty formula above, but also includes graphite to not only enhance and speed up the penetrant action, but also gets down into the pores of the metal for the greatest possible lubrication possible. The cat's-meow of penetrating fluids, can even be used to un-seize frozen engines or as an engine assembly lube! This fluid is also a great choice for use as a drive cable lubricant.
$ 46.95

HCP10333 Aftermarket extreme-duty PENETRATING LUBRICANT, in a generous 16-ounce aerosol can. Same as our standard-duty formula above, but also includes liquid silicone to enhance and speed up the penetrant action. This product is also an exceptional choice for use as a control-cable lubricant.
$ 47.95



Assembly Fluids and Lubricants:

Anti-Seize Paste:

xx1) Fastener ANTI-SEIZE PASTE. Yeah, it's smelly and makes a slippery mess on your fingers, but this stuff is a life-saver for any true wrencher, because it prevents problems down the road. Use it on any metal fastener that does not require a "loctite" thread-locker material to be used. This means on just about every fastener that is carb, engine case, or suspension-related! (except for carb upper and lower rack-mount screws and butterfly valve screws, which do require the use of a thread-lock fluid). If you think that it might, sometime, in the future, need to come off: use anti-seize compound! NOTE: the "base" metal material used in the different anti-seize pastes below do not determine what type of fastener to use such pastes on; it merely signifies what base material is used to create the anti-seize paste. You can use any "base-metal" anti-seize paste on any type of fastener and metal.

NOTE: the use of anti-seize compounds will result in a TORQUE-MULTIPLYING EFFECT……..the result of a reduction in friction between the threaded contact points……and thus fasteners treated with anti-seize compound should have their torque values reduced by at least 10-15% when installed into steel material, and up to 25% into aluminum materials or other “soft” metals” (such as spark plugs into cylinder heads, or almost any other type of fastener into the engine) …… note that this rule applies only to service manual torque specifications on fasteners that are not indicated to be treated with anti-seize fluid by the factory …. if the factory manual specifies the use of an anti-seize coating, then the specified torque value for that fitting already takes into account the “reduced torque” necessary.

http://raskcycle.com/techtip/webdoc14.html

http://www.cncexpo.com/MetricBoltTorqueNm.aspx

http://www.bmwmotorcycletech.info/sparkplugs.htm

http://www.antiseize.com/pdf/torque_specifications.pdf


HCP1264 Aftermarket fastener ANTI-SEIZE PASTE, standard grade aluminum-based in a 1-ounce squeeze tube, for smaller jobs.
$ 8.95

HCP29921 Aftermarket fastener ANTI-SEIZE PASTE, standard grade aluminum-based in a 4-gram pillow pack, for individual jobs (enough for a single carb rack, or front-end rebuild, brake system rebuild, etc.)
$ 3.95

HCP1265 Aftermarket fastener ANTI-SEIZE PASTE, standard grade aluminum-based formula in a 4-ounce tub with a brush-lid, for larger jobs.
$ 9.95

HCP9784 Aftermarket fastener ANTI-SEIZE PASTE, standard grade aluminum-based formula in an 8-ounce tub with a brush-lid, a lifetime supply for your motorcycle!
$ 13.95

HCP9763 Aftermarket fastener ANTI-SEIZE PASTE, standard-grade copper-based formula in an 8-ounce tub with a brush-lid, a lifetime supply for your motorcycle!
$ 13.95

HCP9764 Aftermarket fastener ANTI-SEIZE PASTE, premium-grade nickel-based formula in an 8-ounce tub with a brush-lid, a lifetime supply for your motorcycle!
$ 19.95



xx2) The next most important tool: fastener THREAD LOCKER FLUIDS. Use on any fastener that you don't normally ever remove, to make sure that it stays that way. Comes in a variety of formulas, each one designed for a specific use as explained below. NOTE: the damper rod retaining bolt (in the very bottom of the fork tube lower leg, screwing up into the bottom of the damper rod) requires the use of the HCP1267 / HCP27756 medium-strength or the HCP1268 high-strength thread-locking fluid. Yamaha recommend the high-strength fluid, but we’ve found that the medium-strength fluid works as well and makes future dis-assembly a bit easier.

HCP1266 Low Strength THREAD LOCKER FLUID, 6ml squeeze tube. This is a semi-permanent formula that provides moderate vibration-loosening resistance, while still allowing for easy disassembly of the fastener with hand tools. This formula is recommended for upper and lower carb rack mount screws and the butterfly valve-to-throttle shaft retaining screws. A little bit goes a long way.......
$ 11.95


HCP1267 Semi-Permanent THREAD LOCKER FLUID, 6ml squeeze tube. This is semi-permanent formula that provides good vibration-loosening resistance, while still allowing for easy disassembly of the fastener with hand tools. This formula is recommended for use with 6-20mm fasteners.
$ 11.95

HCP27756 Semi-Permanent THREAD LOCKER FLUID, 0.5ml squeeze tube. This is semi-permanent formula that provides good vibration-loosening resistance, while still allowing for easy disassembly of the fastener with hand tools. This formula is recommended for use with 6-20mm fasteners. Small single-use tube is great for, well, small jobs!
$ 4.95


HCP1268 Permanent THREAD LOCKER FLUID, 6ml squeeze tube. This is a high-strength formula that provides superior vibration-loosening resistance, and requires the use of heat or special tools to break loose the fastener for disassembly.
$ 11.95

HCP1269 Permanent THREAD LOCKER FLUID, 6ml squeeze tube. This is both a high-strength AND high-heat formula that provides superior vibration-loosening resistance, and requires the use of heat or special tools to break loose the fastener for disassembly.
$ 11.95



NOTE: the following product(s) can only be shipped via ground transport (which thus eliminates the postal Priority Mail, postal Express Mail, or private carrier Expedited levels of service for this item) and cannot (and will not----don't even ask!) be shipped outside of the continental USA. Additionally, there may be a per-package weight or quantity restriction, and thus multiple-unit orders of this product may have to be shipped in separate packages and will incur additional shipping charges.

HCP20860 Aftermarket industrial-strength ASSEMBLY LUBE, in a standard 12-ounce aerosol can. Heavy-duty formula includes graphite to not only enhance and speed up the penetrant action, but also gets down into the pores of the metal for the greatest possible lubrication possible. Won't wash away, protect against rust and corrosion, stable from 0-degrees up to 250-F. This fluid is also a great choice for use as a drive cable lubricant.
$ 41.95

HCP20862 Aftermarket super-duty ASSEMBLY LUBE, in a generous 10-ounce aerosol can. The cat's-meow of lubricants, infused with pure moly disulfide, it goes on wet and then dries in 1-2 hours to a super-slick, high-pressure, hi-temp, bearing-like finish which provides the ultimate level of protection. Prevents rust and corrosion, won't wash off, throw off, and won't attract dust or dirt. Surfaces must be clean and dry of previous oils, etc. before application. Can even be used as an engine, tranny, and drivetrain assembly lube!
$ 44.95

HCP20863 Aftermarket super-duty GRAPHITE LUBE, in a generous 10-ounce aerosol can. The 800-pound gorilla of lubricants, it's infused with pure graphite, goes on wet, and then dries in 10 minutes to a super-slick, high-pressure, bearing-like finish which provides the ultimate level of protection. Prevents rust, won't wash off, throw off, and won't attract dust or dirt. Surfaces must be clean and dry of previous oils, etc. before application. Can be used as an engine assembly lube, bearing or bushing pre-lube, great for lock cylinders, and all metallic sliding surfaces. Use where dusty or dirty conditions render oil-based lubricants ineffective or undesirable.
$ 42.95



Fork Tube Cleaning and Polishing:

HCP28489 Fork Tubes DEEP REACH CLEANING BRUSH. This 36" long brush features polyester bristles that will reach deep inside the forks tubes to clean away grit and oil sludge residue that cannot otherwise be reached or disturbed. Has a comfortable easy-grip plastic handle and flexible twisted-wire shaft. .Use with your favorite cleaning solvents to get the insides of the fork tubes free of contaminants.
$ 39.99



ft4) These stainless-steel, bristle-wire DE-BURRING BRUSHES will work wonders on the upper cap bolt area on both the threaded and the non-threaded style of fork tubes. Tubes that use threaded cap bolt (all XJ650 Turbo, all XJ700 models, XJ750-X models, XJ750 Maxim and Midnight Maxim, XJ900RK, and XJ1100 models) should use the HCP10223 butterfly brush; non-threaded tubes can use either the HCP10222 spiral brush or the HCP10223 butterfly brush. Both style brushes have stems that are designed to be used in a standard power drill, and should be used at 850 rpm's or less. These brushes will make quick and meaningful work of the cleaning and polishing of this critical area on your upper fork tubes.

HCP10222 Aftermarket stainless-steel double-density spiral DE-BURRING BRUSH, for use on fork tubes without a threaded cap bolt.
$ 11.95

HCP10223 Aftermarket stainless-steel high-density "butterfly-wings" DE-BURRING BRUSH, for use on fork tubes with or without threaded cap bolts.
$ 11.95



FORK OIL:

Unlike motor oil or gear oil, fork oil's major purpose is not lubrication.....rather, it acts as part of the suspension system, providing both damping and rebound control functions. The different "weight" or viscosity of fork oils allows you to modify the ride and handling characteristics of your bike in a fairly simple way.

And yes, it IS a lubricant also!

Although many people----including, unbelievably, Yamaha itself----recommends the use of engine motor oil as a substitute for fork oil, this is not a very good idea. Engine oils (or any multi-viscosity oil) uses additives and detergents that, while wonderful in for their intended purposes inside an engine block, tranny case, or rear drive unit, are not such a good idea inside forks. Forks operate at a much lower temperature and temperature RANGE than engine and drivetrains do, and thus do not need all those additives. And fork oil also tends to contain higher percentages of molybdenum disulfide and anti-foaming agents than engine or gear oil, both of which are very important to proper fork operation.

As a small example.......most motor oils are of a multi-viscosity nature (such as 10W30) which change their viscosity in relation to their temperature (thin when cool, thicker as they warm). A very necessary and useful feature for an engine, where you do not want your oil thinning out as the engine warms up. Not such a good idea for your suspension----unless for some reason you WANT your handling characteristics to change (get stiffer) as the forks heat up!


Proper fork oil levels and scheduled change intervals are important for fork performance and fork part longevity.....water contamination, as well as particulate wear will accumulate in fork oil, and since there is no oil filtering mechanism within your forks, the only way to get the grit and gunk out (before it chews up your oil seals and slider bearings!) is to change your fork fluid regularly. Yamaha recommends a fork fluid change every 10,000 miles or 24 months (all models except XJ700's), or every 16,000 miles or 24 months (all XJ700 and XJ750-X models). If you just bought a used bike, we recommend you do a fluid change as soon as possible, because just like other routine maintenance tasks (besides engine oil changes), this is one that has very likely been ignored for the last 10-12 years!

HINT: there’s a puddle of fluid under your wheel, in the area of the brake caliper. Unless the source of the leak is fully obvious, how can you tell if it’s brake fluid of fork oil? Try to mix a few drops of water into the fluid; fork oil (or engine/gear oil) won’t mix and the water will “ball up”; brake fluid will integrate with water and absorb the water.


Fork oil capacities and recommended weights are as follows. The amounts listed are per fork tube:


XJ550 Maxim: 272cc or 9.20 fluid ounces. 10W fork oil.

XJ550 Seca: 230cc or 7.78 fluid ounces. 10W fork oil.

1980-81 XJ650 Maxim and Midnight Maxim: 262cc or 8.86 fluid ounces. 10W fork oil.

1982-84 XJ650 Maxim: 278cc or 9.40 fluid ounces. 10W fork oil.

1982 XJ650RJ Seca: 236cc or 7.98 fluid ounces. 10W fork oil. Fork oil level is specified as 400mm (15.75") below the top of the tube without the spring installed, forks fully collapsed.

1982 XJ650LJ Turbo: 238cc or 8.04 fluid ounces. 10W fork oil. Fork oil level is specified as 180mm (7.09") below the top of the tube without the spring installed, forks fully collapsed.

1983 XJ650LK Turbo: unknown.

1985-86 XJ700 non-X: 383cc or 12.96 fluid ounces. 10W fork oil.

1985-86 XJ700-X: 389cc or 13.16 fluid ounces. 10W fork oil.

1982 XJ750 Maxim: 257cc or 8.69 fluid ounces. 10W fork oil.

1983 XJ750 Maxim and Midnight Maxim: 257cc or 8.69 fluid ounces. 10W fork oil. NOTE: owner's manual states that the fork oil capacity is 278cc (9.40 fluid ounces). It is unknown which measurement is correct.

1981-83 XJ750 Seca: 309cc or 10.45 fluid ounces. 20W fork oil.

1983 XJ750 E-II Seca or 1984 XJ750RL Seca: 286cc or 9.67 fluid ounces. 5W fork oil. Fork oil level is specified as 168mm (6.61") below the top of the tube without the spring installed, forks fully collapsed.

1983 XJ900RK Seca: 286cc or 9.67 fluid ounces. 5W fork oil. Fork oil level is specified as 164mm (6.46") below the top of the tube without the spring installed, forks fully collapsed.

1982-84 XJ1100 Maxim and Midnight Maxim: 210cc or 7.10 fluid ounces. 10W fork oil. Fork oil level is specified as 210mm (8.27") below the top of the tube without the spring installed, forks fully collapsed.


IMPORTANT NOTE: the above fork oil VOLUMES are for use only when using the stock fork springs. The use of aftermarket performance front fork coil springs will change those volumes, since aftermarket springs are thicker than stock----and thus displace more oil. Using the stock oil fluid VOLUME with aftermarket fork springs is a sure way to OVERFILL your forks, with the very real possibility of blowing out fork seals.


Unlike with your engine oil, where a bit too much or too little oil volume in the crankcase is not really a significant concern, with fork oil, too much or too little can cause real problems (too much oil can result in blown oil seals and a stiff, harsh ride, while too little oil volume results in excessive foaming, a soft mushy ride with possible bottoming, and erratic fork performance and lots of front end "dive" upon braking).

A better way to determine the amount of fork oil that is needed and necessary is via the measurement of the fork oil LEVEL within the tubes.....sort of like measuring the oil level with a dipstick. Yamaha does not specify this level for all models; and in any case, if using aftermarket springs, the factory oil level recommendation is not always useful. The maximum oil level should be 5-1/2" (140mm) below the top of the inner fork tube, measured with all internal fork tube components installed EXCEPT FOR THE SPRINGS, and with the inner fork tube fully collapsed into the lower (outer) tube.

In order to be as accurate as possible, we recommend the use of a suitable measuring device, such as the HCP1728 oil level syringe listed further below.

And finally, the fork oil viscosity can be changed from the factory recommendations to give a softer or firmer ride.......the lower the viscosity, the thinner the oil, and the softer the ride (i.e. 5W oil is thinner than 10W which is thinner than 20W, etc.) In this regard, you would certainly be correct in thinking of fork oil as a suspension "tuning tool"! Note that a thicker oil viscosity will have much more effect on the fork "rebound" characteristics than it will on the fork compression dampening function.

A great primer on "tuning" your forks via adjusting the oil levels can be seen at:

http://www.thumpertalk.com/forum/archive/index.php/t-89918.html

while the theory and science and practical applications of tuning your suspension via using differing viscosities of fork oil can is revealed at:

http://www.peterverdone.com/archive/lowspeed.htm


NOTE: the following product(s) can only be shipped via ground transport (which thus eliminates the postal Priority Mail, postal Express Mail, or private carrier Expedited levels of service for this item) and cannot (and will not----don't even ask!) be shipped outside of the continental USA. Additionally, there may be a per-package weight or quantity restriction, and thus multiple-unit orders of this product may have to be shipped in separate packages and will incur additional shipping charges.


ffo3) Red Line Oil products line of SYNTHETIC FORK OILS are some of the best, highest-performance fork oils developed specifically for this purpose. They provide exceptional shear lubrication, are highly resistant to any viscosity changes, and provide excellent seal lubrication as well as very high anti-foaming properties. All of these oils are completely compatible with each other, which means that different weights can safely be mixed with each other to create "custom-weights" of fork oil for the utmost in suspension tuning flexibility. NOTE: oils, if mixed for a different viscosity, should be done in a large enough batch to provide enough oil for both front forks. You do NOT want to be running different oil viscosity's in the left and right fork tubes!

Also, do not mix different brands, styles, or types of oils........you can only safely mix forks oils together from one manufacturer!


HCP1563 Red Line high-performance SYNTHETIC FORK OILS 0W (zero weight, "like water"), 16 ounce bottle (473cc), clear. Each bottle:
$ 22.95

HCP1564 Red Line high-performance SYNTHETIC FORK OIL 2.5W, 16 ounce bottle (473cc), blue. Each bottle:
$ 22.95

HCP1258 Red Line high-performance SYNTHETIC FORK OIL 5W, 16 ounce bottle (473cc), amber. Each bottle:
$ 22.95

HCP1259 Red Line high-performance SYNTHETIC FORK OIL 10W, 16 ounce bottle (473cc), red. Each bottle:
$ 22.95

HCP1263 Red Line high-performance SYNTHETIC FORK OIL 30W, 16 ounce bottle (473cc), orange. NOTE: this oil is similar in viscosity to what most other oil manufacturers call "20W" oil. Each bottle:
$ 22.95



ffo4) PJ1 products line of TUNER FORK OILS are exceptional quality, value-priced fork oils developed specifically for motorcycle suspensions. All of these oils are completely compatible with each other, which means that different weights can safely be mixed with each other to create "custom-weights" of fork oil for the utmost in suspension tuning flexibility. NOTE: oils, if mixed for a different viscosity, should be done in a large enough batch to provide enough oil for both front forks. You do NOT want to be running different oil viscosity's in the left and right fork tubes!

Also, do not mix different brands, styles, or types of oils........you can only safely mix forks oils together from one manufacturer!


HCP10360 PJ1 products TUNER FORK OIL 2.5W, 16 ounce bottle (473cc). Each bottle:
$ 19.95

HCP10362 PJ1 products TUNER FORK OIL 5W, 16 ounce bottle (473cc). Each bottle:
$ 19.95

HCP10364 PJ1 products TUNER FORK OIL 7.5W, 16 ounce bottle (473cc). Each bottle:
$ 19.95

HCP10366 PJ1 products TUNER FORK OIL 10W, 16 ounce bottle (473cc). Each bottle:
$ 19.95

HCP10368 PJ1 products TUNER FORK OIL 15W, 16 ounce bottle (473cc). Each bottle:
$ 19.95

HCP10370 PJ1 products TUNER FORK OIL 20W, 16 ounce bottle (473cc). Each bottle:
$ 19.95

HCP10372 PJ1 products TUNER FORK OIL 30W, 16 ounce bottle (473cc). Each bottle:
$ 19.95



Fork Tube Oil Level Gauges:

HCP1728 Fork tube oil fluid level measurement GAUGE AND SYRINGE. This handy tool makes the measurement of the fork oil level easy and accurate. NOTE: the proper amount of fork oil is determined via the measurement of the fork oil LEVEL (distance below the very top of the inner tube) rather than a volume AMOUNT of oil specification. Too little oil will make the ride mushy, while too much oil makes the ride harsh (and can blow out the oil seals!)
$ 37.95




ffl4) Aftermarket fork oil measurement GRADUATED CYLINDERS. The best way to measure the precise amount of fork oil fluid is via the use of these lab-quality measurement cylinders. Available in either transparent (clear) or translucent (cloudy) durable plastic construction, they all have easy-to-read scale numerals (milliliters) and feature a "non-wetting" inner surface coating that prevents the concave "meniscus" from forming at the top of the fluid, thus insuring a much more accurate level reading. Large bases insure stability while large spouts make "the pour" easy and prevent messy drips. Very useful device to have for front fork oil changes.


HCP10741 Aftermarket fork oil GRADUATED CYLINDER, 250ml capacity, translucent (cloudy).
$ 16.95

HCP10744 Aftermarket fork oil GRADUATED CYLINDER, 250ml capacity, transparent (clear).
$ 27.95

HCP10742 Aftermarket fork oil GRADUATED CYLINDER, 500ml capacity, translucent (cloudy).
$ 19.95

HCP10745 Aftermarket fork oil GRADUATED CYLINDER, 500ml capacity, transparent (clear).
$ 39.95

HCP10743 Aftermarket fork oil GRADUATED CYLINDER, super-sized 1000ml capacity, translucent (cloudy), with convenient side handle to insure steady pouring.
$ 59.95



Fork Tube Air Pressure Tool and Gauge:

HCP9196 Aftermarket AIR VALVE STEM TOOL, handy 4-in-1 tool allows you to properly remove and insert the stem core, and also clean/chase/re-thread the internal and external stem threads.
$ 5.95

HCP9108 Aftermarket air-assisted forks LOW PRESSURE AIR GAUGE, heavy-duty 0-20 psi pencil (stick) pressure gauge marked in 1/2-psi increments, perfect for checking fork air pressures on models so equipped. Very high quality and much more accurate than standard tire pressure gauges, which is very important on the fork pressures as an imbalance between the fork pressure can lead to steering and stability issues, while too much pressure will blow out the lower tube oil seals!
$ 7.95
Return to Top of Page