XJ4Ever.com
PO Box 98393
Atlanta, GA 30359-8393
Info@xj4ever.com


Home - Catalog - How-To's - XJBikes.com Forum

SECTION H:

CLUTCH/TRANSMISSION/DRIVETRAIN:

DRIVELINE TOOLS:

Driveline Service Tools:

NOTE: SOME OF THE FOLLOWING TOOLS ARE AVAILABLE FOR RENTAL!!: some tools are a one-time or infrequent use tool, so it may be more economical for you to rent them from us, rather than to purchase outright. Please see the “rental” section within the THE TOOLBOX section of our catalog at:

http://xjbikes.com/forums/index.php?threads/xj-parts-catalog-section-p-the-toolbox.44630

and review the availability and procedures in the TOOL RENTAL section.


HCP9214 Aftermarket driveshaft REMOVER TOOL. Designed to be used with a slide hammer, this special "gear puller jaws" tool is designed to precisely fit around the large gear on the back end of the driveshaft and is used to "yank" and break the driveshaft free of the cross-joint splines, thus allowing the drive shaft to be removed through the rear of the swingarm. For all shaft-drive XJ-series bikes.
$ 79.95


HCP9211 Aftermarket middle drive gear SHAFT NUT REMOVAL SOCKET. Special thin, large diameter recessed hub socket needed to remove the bearing retaining nut on the middle drive gear. For use with all shaft-drive XJ-series except XJ1100 models.
$ 119.95

HCP9210 Aftermarket middle drive gear GEAR LASH MEASURING TOOL. For all XJ1100 models. This tool is designed to be used in conjunction with a dial indicator gauge.
$ 29.95



HCP9213 Aftermarket final drive input pinion gear PINION GEAR REMOVER ADAPTER TOOL. Designed to be used with a slide hammer, this special adapter screws onto the input gear shaft and then you can "bang" it out with a slide hammer tool. For all shaft-drive XJ-series bikes.
$ 59.95

HCP9291 Aftermarket final drive input pinion gear BEARING RETAINER WRENCH. The input shaft bearing is retained by a special retaining ring that requires this pegged drive socket to remove. For all shaft-drive XJ models except XJ1100 models.
$ 89.95

HCP9212 Aftermarket final drive input pinion gear coupler GEAR HOLDER TOOL, necessary for measuring and setting the gear lash correctly or for removing the final drive input shaft. For all XJ-series shaft-drive models.
$ 159.95



HCP9209 Aftermarket final drive output ring gear COLLAR, OIL SEAL, and ROLLER BEARING INSTALLATION AND REMOVAL TOOL SET, necessary for proper removal and installation of these parts. Set of two tools, one for removal and the other for installation. For all XJ-series shaft-drive models.
$ 129.95



Super-Penetrant Fluids and Lubricants:

Sometimes, the toughest part of working on a vehicle is battling the effects of time: seized fasteners, caused by rust, corrosion, and other factors, turns what should be a 5-minute effort into a 50-minute (or more) chore, complete with rounded-off, ruined, or snapped fasteners, e-z outs, heli-coil inserts, and more.........and that's just not right.

While the proper use of our various Anti-Seize products will prevent these nightmares from occurring in the future, you're stuck in the here-and-now, and the best way to handle these obstacles is to have the proper tools at the stand-by; and in the case of fastener seizure, the proper "tool" is a can or two of our SUPER PENETRATING LUBRICANTS at the ready; a couple of squirts, a little bit of time-----perhaps some heat for those really nasty situations----and you're on your way again, hopefully not too much worse for the experience.....

Great for use on all fasteners, fork tube cap bolts, intake and exhaust manifolds bolts, studs, and nuts, lock cylinder tumblers, or anywhere an un-cooperative fastener can be found. Can even be used to help un-seize frozen engines!

Be aware that these products are not your typical, garden-variety, run-of-the-mill "retail" type products; these are designed an used as industrial- and military-strength products, meaning they have special formulations that include a dollop more of the "good stuff" within them to solve the toughest seizure problems imaginable (the "good stuff" ingredients cost more, and it is those compounds that are left out of or reduced in concentration in "retail" level consumer products).

NOTE: the following product(s) can only be shipped via ground transport (which thus eliminates the Priority Mail level of service for this item) and cannot (and will not----don't even ask!) be shipped outside of the continental USA. Therefore it may have to be shipped in a separate package from the remainder of your order, and will thus incur additional shipping charges.

HCP10331 Aftermarket standard-duty PENETRATING LUBRICANT, in a generous 16-ounce aerosol can. Oil-based lubricant penetrates down into spaces of one-millionth of an inch to handle the most reluctant seizures. Actually dissolves the rust and corrosion that causes the seizure; lubricates and displaces moisture to prevent rust re-formation. This product is what we use and recommend for freeing stuck fork tube cap bolts and other such challenging fasteners.
$ 24.95

HCP11974 Aftermarket super-duty PENETRATING LUBRICANT, in a generous 13-ounce aerosol can. Same as our standard-duty formula above, but also includes graphite to not only enhance and speed up the penetrant action, but also gets down into the pores of the metal for the greatest possible lubrication possible. The cat's-meow of penetrating fluids, can even be used to un-seize frozen engines or as an engine assembly lube! This fluid is also a great choice for use as a drive cable lubricant.
$ 26.95

HCP10333 Aftermarket extreme-duty PENETRATING LUBRICANT, in a generous 16-ounce aerosol can. Same as our standard-duty formula above, but also includes liquid silicone to enhance and speed up the penetrant action. This product is also an exceptional choice for use as a control-cable lubricant.
$ 27.95




Assembly Fluids and Lubricants:

NOTE: the following product(s) can only be shipped via ground transport (which thus eliminates the Priority Mail level of service for this item) and cannot (and will not----don't even ask!) be shipped outside of the continental USA. Therefore it may have to be shipped in a separate package from the remainder of your order, and will thus incur additional shipping charges.

HCP20860 Aftermarket industrial-strength ASSEMBLY LUBE, in a standard 12-ounce aerosol can. Heavy-duty formula includes graphite to not only enhance and speed up the penetrant action, but also gets down into the pores of the metal for the greatest possible lubrication possible. Won't wash away, protect against rust and corrosion, stable from 0-degrees up to 250-F. This fluid is also a great choice for use as a drive cable lubricant.
$ 21.95

HCP20862 Aftermarket super-duty ASSEMBLY LUBE, in a generous 10-ounce aerosol can. The cat's-meow of lubricants, infused with pure moly disulfide, it goes on wet and then dries in 1-2 hours to a super-slick, high-pressure, hi-temp, bearing-like finish which provides the ultimate level of protection. Prevents rust and corrosion, won't wash off, throw off, and won't attract dust or dirt. Surfaces must be clean and dry of previous oils, etc. before application. Can even be used as an engine, tranny, and drivetrain assembly lube!
$ 24.95

HCP20863 Aftermarket super-duty GRAPHITE LUBE, in a generous 10-ounce aerosol can. The 800-pound gorilla of lubricants, it's infused with pure graphite, goes on wet, and then dries in 10 minutes to a super-slick, high-pressure, bearing-like finish which provides the ultimate level of protection. Prevents rust, won't wash off, throw off, and won't attract dust or dirt. Surfaces must be clean and dry of previous oils, etc. before application. Can be used as an engine assembly lube, bearing or bushing pre-lube, great for lock cylinders, and all metallic sliding surfaces. Use where dusty or dirty conditions render oil-based lubricants ineffective or undesirable.
$ 21.95



Final Drive Gear Oil:

As with other high-stress, high-heat mechanical area, your final drive system needs a top-quality lubricant and regular oil changes to maintain its performance and insure the longest life of the components. All shaft-drive XJ models should have their rear fluid changed every 5,000 miles (all XJ650, 1981-84 XJ750 except XJ750RL, and XJ1100 models) or every 16,000 miles (all XJ700, XJ750RL, and XJ900 models), and use SAE 80W or SAE 80W/90 Type GL-4 Hypoid Gear Oil. The final drive holds 0.2 liters of fluid (about 1/2 of a pint).

Our PETROLEUM-BASED GEAR OIL easily meets all original specifications, is an excellent value, and comes in a 1 quart container, enough for 2 oil changes.

Our "SHOCK-PROOF" SYNTHETIC GEAR OIL is the finest product you can purchase for the use in your final drive system and far exceeds the OEM specifications. Sold in a 1 quart container, enough for 2 oil changes.


NOTE: the following product(s) can only be shipped via ground transport (which thus eliminates the Priority Mail level of service for this item) and cannot (and will not----don't even ask!) be shipped outside of the continental USA. Therefore it may have to be shipped in a separate package from the remainder of your order, and will thus incur additional shipping charges.

HCP10374 Aftermarket petroleum-based 85-90W FINAL DRIVE GEAR OIL, 1 quart bottle.
$ 13.95

HCP9844 Aftermarket synthetic "shock-proof" 80W FINAL DRIVE GEAR OIL, 1 quart bottle.
$ 24.95



Gear Assembly Grease:

HCP8608 Aftermarket gear and bearing synthetic RED MOLY GREASE. High temperature, water resistant, extreme pressure and high-load strength synthetic organic moly grease is far superior to black moly disulfide (petroleum-based) products. Use on steering neck bearings, wheel bearings, starter motor gears, driveshaft splines, swingarm and final drive bearings. 14 oz. tube.
$ 24.95
Return to Top of Page