XJ4Ever.com
PO Box 98393
Atlanta, GA 30359-8393
Info@xj4ever.com


Home - Catalog - How-To's - XJBikes.com Forum

SECTION F:

EXHAUST:

--Hardware.


EXHAUST SYSTEM HARDWARE:

eh5) Original and aftermarket EXHAUST SYSTEM HARDWARE perfectly replaces the stripped, damaged, rusted or missing originals. It is always a great idea to replace these hardware items whenever you have your system apart. And as usual, ALWAYS use anti-seize compound on the threads of any exhaust system fastener during assembly!

Exhaust system hardware is listed below BY MODEL. Within each model listing, the hardware products list starts at the "beginning" of the exhaust system---meaning where the header pipes attach to the cylinder head exhaust port----and then proceed from there, more-or-less in the following order (some models vary slightly in their layout and orientation):

* the cylinder head THREADED STUDS, their special FLANGED NUTS, and the large finned, cast aluminum RING NUT---which of course really isn't a nut at all! By the way, I can't stress just how great an idea it is to replace the flange nuts whenever you remove your originals, for whatever reason.

* the header pipe exhaust gas analysis test port BOLT and its WASHER.

* the joint where the header pipe outlet fits into the collector box inlet. On most models, the pinch clamp at this joint is permanently attached to the collector box inlet, and the only replaceable items are the pinch clamp BOLT and WASHER. The XJ1100 models are the only ones that use a replaceable PINCH CLAMP.

Please note that we do offer replacement, chrome-plated single-bolt PINCH CLAMPS that can be used to replace damaged or rusty originals on most other models; however, since the original pinch clamps are spot-welded onto the collector inlet pipes, you will have to carefully cut away or break the spot weld in order to replace them. The replacement clamps will fit and seal like the originals, but do not have the outer edge flanges as original clamps did (but this will not affect their ability to seal properly). Each replacement pinch clamp come complete with a bolt, washer, and nut.

* the collector box attaching hardware needed to secure the collector box---and by design, to also support the weight of almost the entire exhaust system----to the frame. Varies by model, but usually consists of a Bolt that goes through the collector box, which is then insulated by a rubber INSULATOR, and which attaches via a COLLAR to a "u"-shaped metal BRACKET. This Bracket is then attached to the bike frame via two BOLTS and WASHERS.

It should be noted that worn insulators (dampers) in this part of your exhaust system can lead to excessive vibration (buzzing) in the system, and it is recommended that you periodically inspect them for integrity and the mounting hardware in this critical area for security and correct tightness.

Also, note that XJ650 Maxim and Midnight Maxim models, as well as XJ1100 models, do not use a "collector box" and thus there is no associated exhaust system-to-frame mounting hardware, brackets, etc. on those models.

* the joint where the collector box outlet (or equivalent) fits into the muffler inlet stub pipe. On most models, the PINCH CLAMP at this joint is permanently attached to the muffler inlet stub pipe, and the only replaceable items are the pinch clamp BOLT and WASHER. XJ1100 models are the only ones that use replaceable PINCH CLAMPS, in addition to the fasteners.

Please note that we do offer replacement, chrome-plated single-bolt PINCH CLAMPS that can be used to replace damaged or rusty originals on most other models; however, since the original pinch clamps are spot-welded onto the collector outlet (or muffler inlet) pipes, you will have to carefully cut away or break the spot weld in order to replace them. The replacement clamps will fit and seal like the originals, but do not have the outer edge flanges as original clamps did (but this will not affect their ability to seal properly). Each replacement pinch clamp come complete with a bolt, washer, and nut.

* finally, our tour ends at the muffler bracket-to-footrest bracket (or frame) mounting BOLT, WASHER, and NUTS, as well as the rubber BUMPER that is mounted on the left muffler can to cushion against the centerstand while it is in the "up" position.


NOTE: the torque specification is 7.5 foot-pounds for the exhaust header pipe-to-cylinder head stud flange nut.

NOTE: for all XJ550 and XJ650 models, the HCP577 exhaust header pipe Ring Nut is a bright, semi-polished natural aluminum, while the HCP578 Ring Nut is black-plated. Since both ring nuts share all the same critical dimensions, the black HCP578 ring nut can be used in place of the natural-finish HCP577 ring nut on all engines for a more aggressive appearance.

NOTE: all of the hardware listed in this section are verified to only fit stock, factory original exhaust systems only! We have no knowledge or experience with any of these items fitting any aftermarket exhaust systems.


NOTE: if the threaded holes in the exhaust system clamps or pipes have minor damage or rust damage, they can usually be easily salvaged with a thread-chaser/tap:

HCP2399 THREAD CHASER AND CLEAN-UP TAP, made from a high-speed titanium nitride coated steel. For the following holes: all XJ550 - XJ900 models cylinder head exhaust port stud holes, and header pipe test port holes. Any of the turbocharger threaded holes which are an M6 size will also use this size tap.
$ 12.95

HCP11028 THREAD CHASER AND CLEAN-UP TAP, made from a high-speed titanium nitride coated steel. For the following holes: all XJ1100 and XS1100 models cylinder head exhaust port stud holes and most collector inlet and outlet cinch clamp threaded holes. Any of the turbocharger threaded holes which are an M8 size will also use this size tap.
$ 12.95

HCP26760 THREAD CHASER AND CLEAN-UP TAP, made from a high-speed titanium nitride coated steel. For the following holes: all XJ and XS1100 models exhaust hanger bolt holes..
$ 17.95


HCP28170 Aftermarket thread tap or EZ-out extractor TAP HANDLE, featuring offset tap handles and fully adjustable head for all m3-m12 size taps and size 0 to ½” extractors. This is the proper way to hold a tap or extractor to insure that the force is directed straight down and doesn’t “wobble” as you are cutting, reaming, or extracting. Much better than using pliers or vise-grips to hold the tool……..
$ 17.95



NOTE: always use a proper thread-cutting oil or lubricant before using thread taps! Thin motor oils work fine when merely doing a "clean-up" thread chase; a real cutting fluid should be obtained if a threaded bore needs to be truly cut:

NOTE: the following product(s) can only be shipped via ground transport (which thus eliminates the Priority Mail level of service for this item) and cannot (and will not----don't even ask!) be shipped outside of the continental USA. Therefore it may have to be shipped in a separate package from the remainder of your order, and will thus incur additional shipping charges.

HCP2402 Aftermarket machinist-grade professional THREAD CUTTING FLUID, for use when cutting into aluminum or other soft metal. 4-ounce non-aerosol can.
$ 8.95

HCP2403 Aftermarket machinist-grade professional THREAD CUTTING FLUID, for use when cutting into steel or other ferrous metals. 4-ounce non-aerosol can.
$ 8.95



XJ550 all models:

HCP2941 OEM cylinder head exhaust port THREADED STUD, use 2 per header pipe, for on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models. Each:
$ 3.95

HCP2941SET8 OEM cylinder head exhaust port THREADED STUDS, set of 8:
$ 24.95


HCP19160 Aftermarket cylinder head exhaust port THREADED STUD, use 2 per header pipe, for on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models. Each:
$ 2.95

HCP19160SET8 Aftermarket cylinder head exhaust port THREADED STUDS, set of 8:
$ 17.95



HCP581 OEM header pipe to above stud SPECIAL TALL FLANGED NUT with the 6mm allen-key drive. Use 2 per header pipe on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models. NOTE: original nuts featured a bright finish, these are now supplied with a dark finish. Each:
$ 3.95

HCP581SET8 OEM header pipe to above stud SPECIAL TALL FLANGED NUT, set of 8:
$ 27.95


HCP26769 Aftermarket header pipe to above stud FLANGED NUT, made from alloy steel with a bright zinc-plated finish. A more affordable option than the factory nuts, but note that these aftermarket nuts are regular-height, and do not feature the hex-drive opening (so you’ll need to use a deep 10mm socket to install them). Use 2 per header pipe on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models, each:
$ 1.95

HCP26769SET8 Aftermarket header pipe to above stud FLANGED NUT, set of 8:
$ 11.95


HCP24409 Aftermarket header pipe to above stud FLANGED NUT, made from super-corrosion resistant 316 stainless steel. Note that these aftermarket nuts are regular-height, and do not feature the hex-drive opening (so you’ll need to use a deep 10mm socket to install them). Use 2 per header pipe on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models, each:
$ 2.95

HCP24409SET8 Aftermarket header pipe to above stud FLANGED NUT, set of 8:
$ 19.95



HCP24431 OEM header pipe INSTALLATION KIT, contains all 8 threaded studs (HCP2941) and special tall flanged nuts (HCP581), do it all at once and get it over with! Use on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models.
$ 49.95

HCP24432 Aftermarket header pipe INSTALLATION KIT, contains all 8 threaded studs (HCP19160) and stainless steel nuts (HCP24409), do it all at once and get it over with! Use on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models.
$ 34.95



HCP577 OEM header pipe large finned, cast aluminum RING NUT, natural finish, use 1 per pipe, for all XJ550 models, each:
$ discontinued



HCP2182 OEM header pipe gas analysis test port BOLT, 6-point hex head alloy steel fastener with a bright finish, use 1 per pipe, for all XJ550 models, each:
$ 2.95

HCP22180 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head alloy steel fastener with a dark finish, use 1 per pipe, for all XJ550 models, each:
$ 1.25

HCP22182 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head 18/8 stainless steel fastener with a bright finish, use 1 per pipe, for all XJ550 models, each:
$ 1.75

HCP22183 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head 316 stainless steel fastener with a bright finish, use 1 per pipe, for all XJ550 models, each:
$ 1.95

HCP22181 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head alloy steel fastener has a serrated flange (which eliminates the need for using a lockwasher) and features a dark finish, use 1 per pipe, for all XJ550 models, each:
$ 1.95



HCP2173 OEM header pipe gas analysis test port bolt FLAT WASHER, use 1 per pipe, for all XJ550 models, original bright finish, each:
$ 1.95

HCP6642 Aftermarket starter motor-to-engine case mounting bolt FLAT WASHER, required for use with any of the aftermarket mounting bolts listed above. Zinc-plated steel. Use 1 per long or short aftermarket bolts. Each:
$ 0.95

HCP6643 Aftermarket starter motor-to-engine case mounting bolt FLAT WASHER, required for use with any of the aftermarket mounting bolts listed above. 18-8 stainless steel with a bright finish. Use 1 per long or short aftermarket bolts. Each:
$ 1.25

HCP25756 Aftermarket starter motor-to-engine case mounting bolt FLAT WASHER, required for use with any of the aftermarket mounting bolts listed above. 316 stainless steel with a natural finish. Use 1 per long or short aftermarket bolts. Each:
$ 1.95

HCP14285 Aftermarket starter motor-to-engine case mounting bolt FLAT WASHER, required for use with any of the aftermarket mounting bolts listed above. Black-oxide coated 18-8 stainless steel. Use 1 per long or short aftermarket bolts. Each:
$ 1.95

HCP14284 Aftermarket starter motor-to-engine case mounting bolt FLAT WASHER, required for use with any of the aftermarket mounting bolts listed above. Black-oxide coated hardened alloy steel. Use 1 per long or short aftermarket bolts. Each:
$ 2.95



HCP2181 OEM header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel with a satin finish (original was bright polished), hex-head bolt, use 1 per pipe, for all XJ550 models, each:
$ 1.95

HCP17123 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 18/8 stainless steel with a bright finish, hex-head bolt, use 1 per pipe, for all XJ550 models, each:
$ 1.95

HCP22191 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 316 stainless steel with a bright finish, hex-head bolt, use 1 per pipe, for all XJ550 models, each:
$2.25

HCP22189 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel with a yellow zinc-plated finish, hex-head bolt, use 1 per pipe, for all XJ550 models, each:
$ 1.25

HCP17122 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel with a black finish, hex-head bolt, use 1 per pipe, for all XJ550 models, each:
$ 1.50


HCP2537 OEM header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per pipe, for all XJ550 models, each:
$ 1.95

HCP26192 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per pipe, for all XJ550 models, each:
$ 0.95

HCP26193 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 1 per pipe, for all XJ550 models, each:
$ 1.25

HCP17110 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, 316 stainless steel, dull finish, use 1 per pipe, for all XJ550 models, each:
$ 1.95

HCP26189 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, black finish, use 1 per pipe, for all XJ550 models, each:
$ 2.95


HCP10714 Aftermarket chrome-plated header pipe outlet-to-collector inlet PINCH CLAMP, complete with attaching hardware, use 1 per pipe, for all XJ550, XJ650RJ Seca, XJ650 Turbo, and all 1981-84 XJ750 air-cooled models. NOTE: original clamps are spot-welded onto pipe; spot weld must be broken to remove original clamps! Each:
$ 16.95



HCP3931 OEM collector rear support FLANGE BOLT, alloy steel, bright finish, use 1 per bike, for all XJ550 models, each:
$ 2.95

HCP26191 Aftermarket collector rear support FLANGE BOLT, alloy steel, bright finish, use 1 per bike, for all XJ550 models, each:
$ 2.25


HCP3946 OEM collector rear support bolt FLAT WASHER, alloy steel, bright finish, use 1 per bike, for all XJ550 models, each:
$ 3.95

HCP26196 Aftermarket collector rear support bolt FLAT WASHER, alloy steel, bright finish, use 1 per bike, for all XJ550 models, each:
$ 1.95

HCP26197 Aftermarket collector rear support bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 1 per bike, for all XJ550 models, each:
$ 2.95

HCP26198 Aftermarket collector rear support bolt FLAT WASHER, 316 stainless steel, dull finish, use 1 per bike, for all XJ550 models, each:
$ 3.95


HCP2637 OEM collector rear support RUBBER INSULATOR (damper), use 2 per bike, for all XJ550 models, each:
$ 19.95

HCP2634 OEM collector rear support insulator COLLAR, use 1 per bike, for all XJ550 models, each:
$ 17.95



HCP3925 OEM collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel hex-head bolt with a bright finish, use 1 per muffler, for all XJ550 models, each:
$ 2.95

HCP17143 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel hex-head bolt with a bright silver-zinc finish, use 1 per muffler, for all XJ550 models, each:
$ 1.25

HCP22195 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel hex-head bolt with a bright yellow-zinc finish, use 1 per muffler, for all XJ550 models, each:
$ 1.50

HCP17144 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel hex-head bolt with a black finish, use 1 per muffler, for all XJ550 models, each:
$ 1.95

HCP17145 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 18/8 stainless steel hex-head bolt with a bright finish, use 1 per muffler, for all XJ550 models, each:
$ 1.75

HCP22198 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 316 stainless steel hex-head bolt with a bright finish, use 1 per muffler, for all XJ550 models, each:
$ 1.95

HCP22200 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, high-strength alloy steel socket head (hex-key) bolt with a black finish, use 1 per muffler, for all XJ550 models, each:
$ 3.95

HCP22201 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel socket head (hex-key) bolt with a bright finish, use 1 per muffler, for all XJ550 models, each:
$ 3.95

HCP22202 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 18/8 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per muffler, for all XJ550 models, each:
$ 3.95

HCP24125 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 316 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per muffler, for all XJ550 models, each:
$ 4.95


HCP2537 OEM collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per muffler, for all XJ550 models, each:
$ 1.95

HCP26192 Aftermarket collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per muffler, for all XJ550 models, each:
$ 0.95

HCP26193 Aftermarket collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 1 per muffler, for all XJ550 models, each:
$ 1.25

HCP17110 Aftermarket collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, 316 stainless steel, bright finish, use 1 per muffler, for all XJ550 models, each:
$ 1.95

HCP26189 Aftermarket collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, alloy steel, black finish, use 1 per muffler, for all XJ550 models, each:
$ 2.95


HCP9713 Aftermarket chrome-plated collector-outlet-to-muffler inlet PINCH CLAMP, complete with attaching hardware, use 1 per pipe, for all XJ550 models. NOTE: original clamps are spot-welded onto pipe; spot weld must be broken to remove original clamps! Each:
$ 11.95



HCP3930 OEM muffler-to-rear footpeg bracket mounting FLANGE BOLT, alloy steel, bright finish, use 1 per side, for all XJ550 models, each:
$ 6.95

HCP26190 Aftermarket muffler-to-rear footpeg bracket mounting FLANGE BOLT, alloy steel, bright finish, use 1 per side, for all XJ550 models, each:
$ 3.95



HCP3942 OEM muffler mounting bracket bolt OVAL NUT, use 1 per side, for all XJ550 models, each:
$ 19.95

HCP26217 Aftermarket muffler mounting bracket bolt OVAL NUT, use 1 per side, for all XJ550 models, each:
$ 11.95



HCP2640 OEM left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used, for all XJ550 models, each:
$ 7.95

HCP26234 Aftermarket left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used, for all XJ550 models, each:
$ 5.95




1984-85 FJ600 models:

HCP2941 OEM cylinder head exhaust port THREADED STUD, use 2 per header pipe, for on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models. Each:
$ 3.95

HCP2941SET8 OEM cylinder head exhaust port THREADED STUDS, set of 8:
$ 24.95


HCP19160 Aftermarket cylinder head exhaust port THREADED STUD, use 2 per header pipe, for on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models. Each:
$ 2.95

HCP19160SET8 Aftermarket cylinder head exhaust port THREADED STUDS, set of 8:
$ 17.95



HCP581 OEM header pipe to above stud SPECIAL TALL FLANGED NUT with the 6mm allen-key drive. Use 2 per header pipe on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models. NOTE: original nuts featured a bright finish, these are now supplied with a dark finish. Each:
$ 3.95

HCP581SET8 OEM header pipe to above stud SPECIAL TALL FLANGED NUT, set of 8:
$ 27.95


HCP26769 Aftermarket header pipe to above stud FLANGED NUT, made from alloy steel with a bright zinc-plated finish. A more affordable option than the factory nuts, but note that these aftermarket nuts are regular-height, and do not feature the hex-drive opening (so you’ll need to use a deep 10mm socket to install them). Use 2 per header pipe on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models, each:
$ 1.95

HCP26769SET8 Aftermarket header pipe to above stud FLANGED NUT, set of 8:
$ 11.95


HCP24409 Aftermarket header pipe to above stud FLANGED NUT, made from super-corrosion resistant 316 stainless steel. Note that these aftermarket nuts are regular-height, and do not feature the hex-drive opening (so you’ll need to use a deep 10mm socket to install them). Use 2 per header pipe on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models, each:
$ 2.95

HCP24409SET8 Aftermarket header pipe to above stud FLANGED NUT, set of 8:
$ 19.95



HCP24431 OEM header pipe INSTALLATION KIT, contains all 8 threaded studs (HCP2941) and special tall flanged nuts (HCP581), do it all at once and get it over with! Use on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models.
$ 49.95

HCP24432 Aftermarket header pipe INSTALLATION KIT, contains all 8 threaded studs (HCP19160) and stainless steel nuts (HCP24409), do it all at once and get it over with! Use on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models.
$ 34.95



HCP19938 OEM header pipe large finned, cast aluminum RING NUT, use 1 per pipe, for all 1984-85 FJ600 models, each:
$ discontinued



HCP3572 OEM header pipe gas analysis test port BOLT, black finish, 6-point hex-head style, use 1 per pipe, for all 1984-85 FJ600 models, each:
$ 2.95

HCP22159 Aftermarket header pipe gas analysis test port BOLT, zinc-plated alloy steel, 6-point hex-head style, use 1 per pipe, for all 1984-85 FJ600 models, each:
$ 1.00

HCP22160 Aftermarket header pipe gas analysis test port BOLT, 18/8 stainless steel, 6-point hex-head style, use 1 per pipe, for all 1984-85 FJ600 models, each:
$ 1.95

HCP21964 Aftermarket header pipe gas analysis test port BOLT, black-oxide coated alloy steel, socket head (hex-key) style fastener, use 1 per pipe, for all 1984-85 FJ600 models, each:
$ 1.95



HCP1869 OEM header pipe gas analysis test port bolt FLAT WASHER, use 1 per pipe, for all 1984-85 FJ600 models, black-oxide finish, each:
$ 1.95

HCP6642 Aftermarket zinc-plated alloy steel with a natural finish, header pipe gas analysis test port bolt FLAT WASHER, use 1 per pipe, for all 1984-85 FJ600 models, each:
$ 0.95

HCP6643 Aftermarket 18-8 stainless steel header pipe gas analysis test port bolt FLAT WASHER, use 1 per pipe, for all 1984-85 FJ600 models, each:
$ 1.25

HCP25756 Aftermarket 316 stainless steel header pipe gas analysis test port bolt FLAT WASHER, use 1 per pipe, for all 1984-85 FJ600 models, each:
$ 1.95

HCP14285 Aftermarket black oxide-coated 18-8 stainless steel header pipe gas analysis test port bolt FLAT WASHER, use 1 per pipe, for all 1984-85 FJ600 models, each:
$ 1.95



HCP3927 OEM header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel with a black finish, hex-head bolt, use 1 per pipe on the #2 and #3 cylinders, for all 1984-85 FJ600 models, each:
$ 2.95

HCP17123 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 18/8 stainless steel with a bright finish, hex-head bolt, use 1 per pipe on the #2 and #3 cylinders, for all 1984-85 FJ600 models, each:
$ 1.95

HCP22191 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 316 stainless steel with a bright finish, hex-head bolt, use 1 per pipe on the #2 and #3 cylinders, for all 1984-85 FJ600 models, each:
$2.25

HCP22189 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel with a yellow zinc-plated finish, hex-head bolt, use 1 per pipe on the #2 and #3 cylinders, for all 1984-85 FJ600 models, each:
$ 1.25

HCP17122 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel with a black finish, hex-head bolt, use 1 per pipe on the #2 and #3 cylinders, for all 1984-85 FJ600 models, each:
$ 1.50



HCP3945 OEM header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, black finish, use 1 per pipe on the #2 and #3 cylinders, for all 1984-85 FJ600 models, each:
$ 1.95

HCP26192 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per pipe on the #2 and #3 cylinders, for all 1984-85 FJ600 models, each:
$ 0.95

HCP26193 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 1 per pipe on the #2 and #3 cylinders, for all 1984-85 FJ600 models, each:
$ 1.25

HCP17110 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, 316 stainless steel, bright finish, use 1 per pipe on the #2 and #3 cylinders, for all 1984-85 FJ600 models, each:
$ 1.95

HCP26189 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, black finish, use 1 per pipe on the #2 and #3 cylinders, for all 1984-85 FJ600 models, each:
$ 2.95



HCP3928 OEM front crossover pipe pinch clamp BOLT, alloy steel hex-head bolt with a black finish, use 2 per system, for all 1984-85 FJ600 models, each:
$ 2.95

HCP17143 Aftermarket front crossover pipe pinch clamp BOLT, steel hex-head bolt with a bright silver-zinc finish, use 2 per system, for all 1984-85 FJ600 models, each:
$ 1.25

HCP22195 Aftermarket front crossover pipe pinch clamp BOLT, alloy steel hex-head bolt with a bright yellow-zinc finish, use 2 per system, for all 1984-85 FJ600 models, each:
$ 1.50

HCP17144 Aftermarket front crossover pipe pinch clamp BOLT, alloy steel hex-head bolt with a black finish, use 2 per system, for all 1984-85 FJ600 models, each:
$ 1.95

HCP17145 Aftermarket front crossover pipe pinch clamp BOLT, 18/8 stainless steel hex-head bolt with a bright finish, use 2 per system, for all 1984-85 FJ600 models, each:
$ 1.75

HCP22198 Aftermarket front crossover pipe pinch clamp BOLT, 316 stainless steel hex-head bolt with a bright finish, use 2 per system, for all 1984-85 FJ600 models, each:
$ 1.95

HCP22200 Aftermarket front crossover pipe pinch clamp BOLT, high-strength alloy steel socket head (hex-key) bolt with a black finish, use 2 per system, for all 1984-85 FJ600 models, each:
$ 3.95

HCP22201 Aftermarket front crossover pipe pinch clamp BOLT, alloy steel socket head (hex-key) bolt with a bright finish, use 2 per system, for all 1984-85 FJ600 models, each:
$ 3.95

HCP22202 Aftermarket front crossover pipe pinch clamp BOLT, 18/8 stainless steel socket head (hex-key) bolt with a bright finish, use 2 per system, for all 1984-85 FJ600 models, each:
$ 3.95

HCP24125 Aftermarket front crossover pipe pinch clamp BOLT, 316 stainless steel socket head (hex-key) bolt with a bright finish, use 2 per system, for all 1984-85 FJ600 models, each:
$ 4.95



HCP3927 OEM rear crossover pipe pinch clamp BOLT, alloy steel with a black finish, hex-head bolt, use 1 per system, for all 1984-85 FJ600 models, each:
$ 2.95

HCP17123 Aftermarket rear crossover pipe pinch clamp BOLT, 18/8 stainless steel with a bright finish, hex-head bolt, use 1 per system, for all 1984-85 FJ600 models, each:
$ 1.95

HCP22191 Aftermarket rear crossover pipe pinch clamp BOLT, 316 stainless steel with a bright finish, hex-head bolt, use 1 per system, for all 1984-85 FJ600 models, each:
$2.25

HCP22189 Aftermarket rear crossover pipe pinch clamp BOLT, alloy steel with a yellow zinc-plated finish, hex-head bolt, use 1 per system, for all 1984-85 FJ600 models, each:
$ 1.25

HCP17122 Aftermarket rear crossover pipe pinch clamp BOLT, alloy steel with a black finish, hex-head bolt, use 1 per system, for all 1984-85 FJ600 models, each:
$ 1.50


HCP3945 OEM front and rear crossover pipe pinch clamp bolt FLAT WASHER, alloy steel, black finish, use 3 per system, for all 1984-85 FJ600 models, each:
$ 1.95

HCP26192 Aftermarket front and rear crossover pipe pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 3 per system, for all 1984-85 FJ600 models, each:
$ 0.95

HCP26193 Aftermarket front and rear crossover pipe pinch clamp bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 3 per system, for all 1984-85 FJ600 models, each:
$ 1.25

HCP17110 Aftermarket front and rear crossover pipe pinch clamp bolt FLAT WASHER, 316 stainless steel, bright finish, use 3 per system, for all 1984-85 FJ600 models, each:
$ 1.95

HCP26189 Aftermarket front and rear crossover pipe pinch clamp bolt FLAT WASHER, alloy steel, black finish, use 3 per system, for all 1984-85 FJ600 models, each:
$ 2.95



HCP22819 OEM muffler mounting RUBBER DAMPER, helps prevents vibration and a “squeaky” exhaust system. Use 1 per side, this round hard rubber bushing presses into the rear footrest bracket. For all 1984-85 FJ600, 1992-98 XJ600 Seca II, 1982 XJ750 Maxim, and all 1978-80 XS1100 Standard models. Each:
$ 7.95

HCP22820 OEM muffler mounting bolt rubber damper metal SLEEVE. Use 1 per footrest. For all 1984-85 FJ600, 1992-98 XJ600 Seca II, 1982 XJ750 Maxim and 1978-80 XS1100 Standard models. Each:
$ 8.95


HCP19940 OEM muffler mounting FLANGE BOLT, use 1 per side, for all 1984-85 FJ600 models. This bolt goes thru the rubber damper and sleeve. Each:
$ discontinued


HCP3946 OEM muffler mounting bolt FLAT WASHER, alloy steel, bright finish, use 1 per side, for all 1984-85 FJ600 models, each:
$ 3.95

HCP26196 Aftermarket muffler mounting bolt FLAT WASHER, alloy steel, bright finish, use 1 per side, for all 1984-85 FJ600 models, each:
$ 1.95

HCP26197 Aftermarket muffler mounting bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 1 per side, for all 1984-85 FJ600 models, each:
$ 2.95

HCP26198 Aftermarket muffler mounting bolt FLAT WASHER, 316 stainless steel, dull finish, use 1 per side, for all 1984-85 FJ600 models, each:
$ 3.95


HCP3942 OEM muffler mounting bracket bolt OVAL NUT, use 1 per side, for all 1984-85 FJ600 models, each:
$ 19.95

HCP26217 Aftermarket muffler mounting bracket bolt OVAL NUT, use 1 per side, for all 1984-85 FJ600 models, each:
$ 11.95



HCP2640 OEM left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used, for all 1984-85 FJ600 models, each:
$ 7.95

HCP26234 Aftermarket left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used, for all 1984-85 FJ600 models, each:
$ 5.95



1992-98 XJ600 Seca II models:

HCP12321 OEM cylinder head exhaust port THREADED STUD, use 2 per header pipe, for all 1992-98 XJ600 Seca II models, each:
$ 2.95
$ 21.95 per set of 8

HCP22633 OEM header pipe to above stud NUT, use 2 per header pipe, for all 1992-98 XJ600 Seca II models, each:
$ 3.95
$ 24.95 per set of 8



HCP3572 OEM header pipe gas analysis test port BOLT, black finish, use 1 per pipe, for all 1992-98 XJ600 Seca II models, each:
$ 2.95

HCP22159 Aftermarket header pipe gas analysis test port BOLT, zinc-plated alloy steel, 6-point hex-head style, use 1 per pipe, for all 1992-98 XJ600 Seca II models, each:
$ 1.00

HCP22160 Aftermarket header pipe gas analysis test port BOLT, 18/8 stainless steel, 6-point hex-head style, use 1 per pipe, for all 1992-98 XJ600 Seca II models, each:
$ 1.95

HCP21964 Aftermarket header pipe gas analysis test port BOLT, black-oxide coated alloy steel, socket head (hex-key) style fastener, use 1 per pipe, for all 1992-98 XJ600 Seca II models, each:
$ 1.95



HCP1869 OEM header pipe gas analysis test port bolt FLAT WASHER, use 1 per pipe on all for all 1992-98 XJ600 Seca II models, black-oxide finish, each:
$ 1.95

HCP6642 Aftermarket zinc-plated alloy steel with a natural finish, header pipe gas analysis test port bolt FLAT WASHER, use 1 per pipe on all for all 1992-98 XJ600 Seca II models, each:
$ 0.95

HCP6643 Aftermarket 18-8 stainless steel header pipe gas analysis test port bolt FLAT WASHER, use 1 per pipe on all for all 1992-98 XJ600 Seca II models, each:
$ 1.25

HCP25756 Aftermarket 316 stainless steel header pipe gas analysis test port bolt FLAT WASHER, use 1 per pipe on all for all 1992-98 XJ600 Seca II models, each:
$ 1.95

HCP14285 Aftermarket black oxide-coated 18-8 stainless steel header pipe gas analysis test port bolt FLAT WASHER, use 1 per pipe on all for all 1992-98 XJ600 Seca II models, each:
$ 1.95



HCP4623 OEM collector outlet-to-muffler inlet pinch clamp BOLT, use 1 per muffler, for all 1992-98 XJ600 Seca II models, each:
$ 4.95



HCP22819 OEM muffler mounting RUBBER DAMPER, helps prevents vibration and a “squeaky” exhaust system. Use 1 per side, this round hard rubber bushing presses into the rear footrest bracket. For all 1984-85 FJ600, 1992-98 XJ600 Seca II, 1982 XJ750 Maxim, and all 1978-80 XS1100 Standard models. Each:
$ 7.95

HCP22820 OEM muffler mounting bolt rubber damper metal SLEEVE. Use 1 per footrest. For all 1984-85 FJ600, 1992-98 XJ600 Seca II, 1982 XJ750 Maxim and 1978-80 XS1100 Standard models. Each:
$ 8.95



HCP3931 OEM muffler mounting FLANGE BOLT, alloy steel, bright finish, for all 1992-98 XJ600 Seca II models, use 1 per side. This bolt goes thru the muffler mounting rubber damper and sleeve. Each:
$ 2.95

HCP26191 Aftermarket collector (rear) to frame mounting FLANGE BOLT, alloy steel, bright finish, for all 1992-98 XJ600 Seca II models, use 1 per side. This bolt goes thru the muffler mounting rubber damper and sleeve. Each:
$ 2.25



HCP3946 OEM muffler mounting bolt FLAT WASHER, alloy steel, bright finish, 1992-94 XJ600 Seca II models, use 1 per side, each:
$ 3.95

HCP26196 Aftermarket muffler mounting bolt FLAT WASHER, alloy steel, bright finish, 1992-94 XJ600 Seca II models, use 1 per side, each:
$ 1.95

HCP26197 Aftermarket muffler mounting bolt FLAT WASHER, 18/8 stainless steel, bright finish, 1992-94 XJ600 Seca II models, use 1 per side, each:
$ 2.95

HCP26198 Aftermarket muffler mounting bolt FLAT WASHER, 316 stainless steel, dull finish, 1992-94 XJ600 Seca II models, use 1 per side, each:
$ 3.95


HCP4034 OEM muffler mounting bolt FLANGED NUT. Bright finish. Use 1 per bolt. For all 1992-94 XJ600 Seca II models. Each:
$ 5.95

HCP4120 OEM muffler mounting bolt FLANGED NUT. Dark finish. Use 1 per bolt. For all 1995-98 XJ600 Seca II models. Each:
$ 1.25

HCP16245 Aftermarket muffler mounting bolt FLANGED NUT. Bright finish. Use 1 per bolt. For all 1992-98 XJ600 Seca II models. Each:
$ 2.95

HCP16247 Aftermarket muffler mounting bolt FLANGED NUT. Dark finish. Use 1 per bolt. For all 1992-98 XJ600 Seca II models. Each:
$ 3.95




XJ650 all Maxim and Midnight Maxim models:

HCP2941 OEM cylinder head exhaust port THREADED STUD, use 2 per header pipe, for on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models. Each:
$ 3.95

HCP2941SET8 OEM cylinder head exhaust port THREADED STUDS, set of 8:
$ 24.95


HCP19160 Aftermarket cylinder head exhaust port THREADED STUD, use 2 per header pipe, for on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models. Each:
$ 2.95

HCP19160SET8 Aftermarket cylinder head exhaust port THREADED STUDS, set of 8:
$ 17.95



HCP581 OEM header pipe to above stud SPECIAL TALL FLANGED NUT with the 6mm allen-key drive. Use 2 per header pipe on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models. NOTE: original nuts featured a bright finish, these are now supplied with a dark finish. Each:
$ 3.95

HCP581SET8 OEM header pipe to above stud SPECIAL TALL FLANGED NUT, set of 8:
$ 27.95


HCP26769 Aftermarket header pipe to above stud FLANGED NUT, made from alloy steel with a bright zinc-plated finish. A more affordable option than the factory nuts, but note that these aftermarket nuts are regular-height, and do not feature the hex-drive opening (so you’ll need to use a deep 10mm socket to install them). Use 2 per header pipe on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models, each:
$ 1.95

HCP26769SET8 Aftermarket header pipe to above stud FLANGED NUT, set of 8:
$ 11.95


HCP24409 Aftermarket header pipe to above stud FLANGED NUT, made from super-corrosion resistant 316 stainless steel. Note that these aftermarket nuts are regular-height, and do not feature the hex-drive opening (so you’ll need to use a deep 10mm socket to install them). Use 2 per header pipe on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models, each:
$ 2.95

HCP24409SET8 Aftermarket header pipe to above stud FLANGED NUT, set of 8:
$ 19.95



HCP24431 OEM header pipe INSTALLATION KIT, contains all 8 threaded studs (HCP2941) and special tall flanged nuts (HCP581), do it all at once and get it over with! Use on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models.
$ 49.95

HCP24432 Aftermarket header pipe INSTALLATION KIT, contains all 8 threaded studs (HCP19160) and stainless steel nuts (HCP24409), do it all at once and get it over with! Use on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models.
$ 34.95


HCP577 OEM header pipe large finned, cast aluminum RING NUT, natural finish, use 1 per pipe, for all XJ650 Maxim models, each:
$ discontinued

HCP578 OEM header pipe large finned, cast aluminum RING NUT, black finish, use 1 per pipe, XJ650 Midnight Maxim models, each:
$ 49.95



HCP2182 OEM header pipe gas analysis test port BOLT, 6-point hex head alloy steel fastener with a bright finish, use 1 per pipe, for all XJ650 Maxim models, each:
$ 2.95

HCP22180 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head alloy steel fastener with a dark finish, use 1 per pipe, for all XJ650 Maxim models, each:
$ 1.25

HCP22182 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head 18/8 stainless steel fastener with a bright finish, use 1 per pipe, for all XJ650 Maxim models, each:
$ 1.75

HCP22183 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head 316 stainless steel fastener with a bright finish, use 1 per pipe, for all XJ650 Maxim models, each:
$ 1.95

HCP22181 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head alloy steel fastener has a serrated flange (which eliminates the need for using a lockwasher) and features a dark finish, use 1 per pipe, for all XJ650 Maxim models, each:
$ 1.95



HCP3933 OEM header pipe gas analysis test port BOLT, 6-point hex head alloy steel fastener with a dark finish, use 1 per pipe, XJ650 Midnight Maxim models, each:
$ 2.95

HCP22180 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head alloy steel fastener with a dark finish, use 1 per pipe, XJ650 Midnight Maxim models, each:
$ 1.25

HCP22182 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head 18/8 stainless steel fastener with a bright finish, use 1 per pipe, XJ650 Midnight Maxim models, each:
$ 1.75

HCP22183 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head 316 stainless steel fastener with a bright finish, use 1 per pipe, XJ650 Midnight Maxim models, each:
$ 1.95

HCP22181 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head alloy steel fastener has a serrated flange (which eliminates the need for using a lockwasher) and features a dark finish, use 1 per pipe, XJ650 Midnight Maxim models, each:
$ 1.95



HCP2173 OEM header pipe gas analysis test port bolt FLAT WASHER, original bright finish, use 1 per pipe, XJ650 Maxim models, each:
$ 1.95

HCP1869 OEM header pipe gas analysis test port bolt FLAT WASHER, black-oxide finish, use 1 per pipe on all XJ650 Midnight Maxim models, each:
$ 1.95

HCP6642 Aftermarket header pipe gas analysis test port bolt FLAT WASHER, zinc-plated alloy steel with a bright finish, use 1 per pipe on all XJ650 Maxim and Midnight Maxim models, each:
$ 0.95

HCP6643 Aftermarket header pipe gas analysis test port bolt FLAT WASHER, 18-8 stainless steel, use 1 per pipe on all XJ650 Maxim and Midnight Maxim models, each:
$ 1.25

HCP25756 Aftermarket header pipe gas analysis test port bolt FLAT WASHER, 316 stainless steel, use 1 per pipe on all XJ650 Maxim and Midnight Maxim models, each:
$ 1.95

HCP14285 Aftermarket header pipe gas analysis test port bolt FLAT WASHER, black oxide-coated 18-8 stainless steel, use 1 per pipe on all XJ650 Maxim and Midnight Maxim models, each:
$ 1.95



HCP3925 OEM header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel hex-head bolt with a bright finish, use 1 per pipe, XJ650 Maxim models, each:
$ 2.95

HCP17143 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, steel hex-head bolt with a bright silver-zinc finish, use 1 per pipe, XJ650 Maxim models, each:
$ 1.25

HCP22195 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel hex-head bolt with a bright yellow-zinc finish, use 1 per pipe, XJ650 Maxim models, each:
$ 1.50

HCP17144 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel hex-head bolt with a black finish, use 1 per pipe, XJ650 Maxim models, each:
$ 1.95

HCP17145 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 18/8 stainless steel hex-head bolt with a bright finish, use 1 per pipe, XJ650 Maxim models, each:
$ 1.75

HCP22198 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 316 stainless steel hex-head bolt with a bright finish, use 1 per pipe, XJ650 Maxim models, each:
$ 1.95

HCP22200 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, high-strength alloy steel socket head (hex-key) bolt with a black finish, use 1 per pipe, XJ650 Maxim models, each:
$ 3.95

HCP22201 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel socket head (hex-key) bolt with a bright finish, use 1 per pipe, XJ650 Maxim models, each:
$ 3.95

HCP22202 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 18/8 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per pipe, XJ650 Maxim models, each:
$ 3.95

HCP24125 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 316 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per pipe, XJ650 Maxim models, each:
$ 4.95



HCP3928 OEM header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel hex-head bolt with a black finish, use 1 per pipe, XJ650 Midnight Maxim models, each:
$ 2.95

HCP17143 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, steel hex-head bolt with a bright silver-zinc finish, use 1 per pipe, XJ650 Midnight Maxim models, each:
$ 1.25

HCP22195 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel hex-head bolt with a bright yellow-zinc finish, use 1 per pipe, XJ650 Midnight Maxim models, each:
$ 1.50

HCP17144 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel hex-head bolt with a black finish, use 1 per pipe, XJ650 Midnight Maxim models, each:
$ 1.95

HCP17145 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 18/8 stainless steel hex-head bolt with a bright finish, use 1 per pipe, XJ650 Midnight Maxim models, each:
$ 1.75

HCP22198 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 316 stainless steel hex-head bolt with a bright finish, use 1 per pipe, XJ650 Midnight Maxim models, each:
$ 1.95

HCP22200 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, high-strength alloy steel socket head (hex-key) bolt with a black finish, use 1 per pipe, XJ650 Midnight Maxim models, each:
$ 3.95

HCP22201 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel socket head (hex-key) bolt with a bright finish, use 1 per pipe, XJ650 Midnight Maxim models, each:
$ 3.95

HCP22202 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 18/8 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per pipe, XJ650 Midnight Maxim models, each:
$ 3.95

HCP24125 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 316 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per pipe, XJ650 Midnight Maxim models, each:
$ 4.95



HCP2537 OEM header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per pipe, XJ650 Maxim models, each:
$ 1.95

HCP3945 OEM header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, black finish, use 1 per pipe, XJ650 Midnight Maxim models, each:
$ 1.95

HCP26192 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per pipe, XJ650 Maxim or Midnight Maxim models, each:
$ 0.95

HCP26193 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 1 per pipe, XJ650 Maxim or Midnight Maxim models, each:
$ 1.25

HCP17110 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, 316 stainless steel, bright finish, use 1 per pipe, XJ650 Maxim or Midnight Maxim models, each:
$ 1.95

HCP26189 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, black finish, use 1 per pipe, XJ650 Maxim or Midnight Maxim models, each:
$ 2.95



HCP9711 Aftermarket chrome-plated header pipe outlet-to-collector inlet PINCH CLAMP, complete with attaching hardware, use 1 per pipe, for all XJ650 Maxim and Midnight Maxim models. NOTE: original clamps are spot-welded onto pipe; spot weld must be broken to remove original clamps! Each:
$ 11.95



HCP3925 OEM left-to-right crossover pipe pinch clamp BOLT, alloy steel hex-head bolt with a bright finish, use 1, for all XJ650 Maxim models, each:
$ 2.95

HCP17143 Aftermarket left-to-right crossover pipe pinch clamp BOLT, steel hex-head bolt with a bright silver-zinc finish, use 1, for all XJ650 Maxim models, each:
$ 1.25

HCP22195 Aftermarket left-to-right crossover pipe pinch clamp BOLT, alloy steel hex-head bolt with a bright yellow-zinc finish, use 1, for all XJ650 Maxim models, each:
$ 1.50

HCP17144 Aftermarket left-to-right crossover pipe pinch clamp BOLT, alloy steel hex-head bolt with a black finish, use 1, for all XJ650 Maxim models, each:
$ 1.95

HCP17145 Aftermarket left-to-right crossover pipe pinch clamp BOLT, 18/8 stainless steel hex-head bolt with a bright finish, use 1, for all XJ650 Maxim models, each:
$ 1.75

HCP22198 Aftermarket left-to-right crossover pipe pinch clamp BOLT, 316 stainless steel hex-head bolt with a bright finish, use 1, for all XJ650 Maxim models, each:
$ 1.95

HCP22200 Aftermarket left-to-right crossover pipe pinch clamp BOLT, high-strength alloy steel socket head (hex-key) bolt with a black finish, use 1, for all XJ650 Maxim models, each:
$ 3.95

HCP22201 Aftermarket left-to-right crossover pipe pinch clamp BOLT, alloy steel socket head (hex-key) bolt with a bright finish, use 1, for all XJ650 Maxim models, each:
$ 3.95

HCP22202 Aftermarket left-to-right crossover pipe pinch clamp BOLT, 18/8 stainless steel socket head (hex-key) bolt with a bright finish, use 1, for all XJ650 Maxim models, each:
$ 3.95

HCP24125 Aftermarket left-to-right crossover pipe pinch clamp BOLT, 316 stainless steel socket head (hex-key) bolt with a bright finish, use 1, for all XJ650 Maxim models, each:
$ 4.95



HCP3928 OEM left-to-right crossover pipe pinch clamp BOLT, alloy steel hex-head bolt with a black finish, use 1 per bike on all XJ650 Midnight Maxim models, each:
$ 2.95

HCP17143 Aftermarket left-to-right crossover pipe pinch clamp BOLT, steel hex-head bolt with a bright silver-zinc finish, use 1 per bike on all XJ650 Midnight Maxim models, each:
$ 1.25

HCP22195 Aftermarket left-to-right crossover pipe pinch clamp BOLT, alloy steel hex-head bolt with a bright yellow-zinc finish, use 1 per bike on all XJ650 Midnight Maxim models, each:
$ 1.50

HCP17144 Aftermarket left-to-right crossover pipe pinch clamp BOLT, alloy steel hex-head bolt with a black finish, use 1 per bike on all XJ650 Midnight Maxim models, each:
$ 1.95

HCP17145 Aftermarket left-to-right crossover pipe pinch clamp BOLT, 18/8 stainless steel hex-head bolt with a bright finish, use 1 per bike on all XJ650 Midnight Maxim models, each:
$ 1.75

HCP22198 Aftermarket left-to-right crossover pipe pinch clamp BOLT, 316 stainless steel hex-head bolt with a bright finish, use 1 per bike on all XJ650 Midnight Maxim models, each:
$ 1.95

HCP22200 Aftermarket left-to-right crossover pipe pinch clamp BOLT, high-strength alloy steel socket head (hex-key) bolt with a black finish, use 1 per bike on all XJ650 Midnight Maxim models, each:
$ 3.95

HCP22201 Aftermarket left-to-right crossover pipe pinch clamp BOLT, alloy steel socket head (hex-key) bolt with a bright finish, use 1 per bike on all XJ650 Midnight Maxim models, each:
$ 3.95

HCP22202 Aftermarket left-to-right crossover pipe pinch clamp BOLT, 18/8 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per bike on all XJ650 Midnight Maxim models, each:
$ 3.95

HCP24125 Aftermarket left-to-right crossover pipe pinch clamp BOLT, 316 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per bike on all XJ650 Midnight Maxim models, each:
$ 4.95



HCP2537 OEM left-to-right crossover pipe pinch clamp bolt FLAT WASHER, alloy steel, bright finish, XJ650 Maxim models, use 1, each:
$ 1.95

HCP3945 OEM left-to-right crossover pipe pinch clamp bolt FLAT WASHER, alloy steel, black finish, XJ650 Midnight Maxim models, use 1, each:
$ 1.95

HCP26192 Aftermarket left-to-right crossover pipe pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1, XJ650 Maxim or Midnight Maxim models, each:
$ 0.95

HCP26193 Aftermarket left-to-right crossover pipe pinch clamp bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 1, XJ650 Maxim or Midnight Maxim models, each:
$ 1.25

HCP17110 Aftermarket left-to-right crossover pipe pinch clamp bolt FLAT WASHER, 316 stainless steel, bright finish, use 1, XJ650 Maxim or Midnight Maxim models, each:
$ 1.95

HCP26189 Aftermarket left-to-right crossover pipe pinch clamp bolt FLAT WASHER, alloy steel, black finish, use 1, XJ650 Maxim or Midnight Maxim models, each:
$ 2.95



HCP10714 Aftermarket chrome-plated crossover pipe PINCH CLAMP, complete with attaching hardware, use 1 per pipe, for all XJ650 Maxim and Midnight Maxim models. NOTE: original clamp is spot-welded onto the pipe; spot weld must be broken to remove original clamp! Each:
$ 16.95




HCP3926 OEM #1 and #4 header pipe outlet-to-collector inlet pinch clamp SCREW, alloy steel, panhead, phillips-drive, black finish, for all XJ650 Maxim and Midnight Maxim models, use 1 per side, each:
$ 2.95

HCP3114 Aftermarket #1 and #4 header pipe outlet-to-collector inlet pinch clamp SCREW, alloy steel, panhead, phillips-drive, bright finish, for all XJ650 Maxim and Midnight Maxim models, use 1 per side, each:
$ 2.25

HCP3115 Aftermarket #1 and #4 header pipe outlet-to-collector inlet pinch clamp SCREW, 18/8 stainless steel, panhead, phillips-drive, bright finish, for all XJ650 Maxim and Midnight Maxim models, use 1 per side, each:
$ 1.95

HCP26189 Aftermarket #1 and #4 header pipe outlet-to-collector inlet pinch clamp SCREW, 316 stainless steel, panhead, phillips-drive, black finish, for all XJ650 Maxim and Midnight Maxim models, use 1 per side, each:
$ 2.95



HCP2173 OEM #1 and #4 header pipe outlet-to-collector inlet pinch clamp screw FLAT WASHER, original bright finish, use 1 per side on all XJ650 Maxim models, each:
$ 1.95

HCP1869 OEM #1 and #4 header pipe outlet-to-collector inlet pinch clamp screw FLAT WASHER, black-oxide finish, use 1 per side on all XJ650 Midnight Maxim models, use 1 per side, each:
$ 1.95

HCP6642 Aftermarket #1 and #4 header pipe outlet-to-collector inlet pinch clamp screw FLAT WASHER, zinc-plated alloy steel with a bright finish, use 1 per side on all XJ650 Maxim and Midnight Maxim models, use 1 per side, each:
$ 0.95

HCP6643 Aftermarket #1 and #4 header pipe outlet-to-collector inlet pinch clamp screw FLAT WASHER, 18-8 stainless steel, use 1 per side on all XJ650 Maxim and Midnight Maxim models, use 1 per side, each:
$ 1.25

HCP25756 Aftermarket #1 and #4 header pipe outlet-to-collector inlet pinch clamp screw FLAT WASHER, 316 stainless steel, use 1 per side on all XJ650 Maxim and Midnight Maxim models, use 1 per side, each:
$ 1.95

HCP14285 Aftermarket #1 and #4 header pipe outlet-to-collector inlet pinch clamp screw FLAT WASHER, black oxide-coated 18-8 stainless steel, use 1 per side on all XJ650 Maxim and Midnight Maxim models, use 1 per side, each:
$ 1.95



HCP24633 Aftermarket muffler mounting RUBBER DAMPER, helps prevents vibration and a “squeaky” exhaust system. Use 1 per side, this round hard rubber grommet presses into the rear footrest bracket. For all XJ650 Maxim and Midnight Maxim, XJ1100, all 1979-81 XS1100 Special and Midnight Special, and all 1981 XS1100 Standard models,. Each:
$ 21.95



HCP3931 OEM muffler mounting FLANGE BOLT, alloy steel, bright finish, for all XJ650 Maxim and Midnight Maxim models, use 1 per side. This bolt passes thru the muffler hanger flange and the rubber damper. Each:
$ 2.95

HCP26191 Aftermarket muffler mounting FLANGE BOLT, alloy steel, bright finish, for all XJ650 Maxim and Midnight Maxim models, use 1 per side. This bolt passes thru the muffler hanger flange and the rubber damper. Each:
$ 2.25



HCP3946 OEM muffler mounting bolt FLAT WASHER, alloy steel, bright finish, use 1 per side, for all XJ650 Maxim and Midnight Maxim models, each:
$ 3.95

HCP26196 Aftermarket muffler mounting bolt FLAT WASHER, alloy steel, bright finish, use 1 per side, for all XJ650 Maxim and Midnight Maxim models, each:
$ 1.95

HCP26197 Aftermarket muffler mounting bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 1 per side, for all XJ650 Maxim and Midnight Maxim models, each:
$ 2.95

HCP26198 Aftermarket muffler mounting bolt FLAT WASHER, 316 stainless steel, dull finish, use 1 per side, for all XJ650 Maxim and Midnight Maxim models, each:
$ 3.95



HCP3942 OEM muffler mounting bracket bolt OVAL NUT, use 1 per side, for all XJ650 Maxim and Midnight Maxim models, each:
$ 19.95

HCP26217 Aftermarket muffler mounting bracket bolt OVAL NUT, use 1 per side, for all XJ650 Maxim and Midnight Maxim models, each:
$ 11.95



HCP2639 OEM left side muffler rubber BUMPER, for where the centerstand and kickstand contacts the left muffler when not being used. Use 2 of these per bike, for all XJ650 Maxim and Midnight Maxim models, each:
$ 12.95

HCP2640 OEM left side muffler rubber BUMPER, for where the centerstand and kickstand contacts the left muffler when not being used. NOTE: this bumper is approximately 3mm shorter than the original HCP2639 bumper, but will still fit and function properly (and is about 1/2 the price of the correct bumper). Use 2 of these per bike, for all XJ650 Maxim and Midnight Maxim models, each:
$ 7.95

HCP26234 Aftermarket left side muffler rubber BUMPER, for where the centerstand and kickstand contacts the left muffler when not being used. NOTE: this bumper is approximately 3mm shorter than the original HCP2639 bumper, but will still fit and function properly (and is about 1/2 the price of the correct bumper). Use 2 of these per bike, for all XJ650 Maxim and Midnight Maxim models, each:
$ 5.95



XJ650RJ/RJC Seca models:

NOTE: for all XJ550 and XJ650 models, the HCP577 exhaust header pipe Ring Nut is a bright, semi-polished natural aluminum, while the HCP578 Ring Nut is black-plated. Since both ring nuts share all the same critical dimensions, the black HCP578 ring nut can be used in place of the natural-finish HCP577 ring nut on all engines for a more aggressive appearance.

HCP2941 OEM cylinder head exhaust port THREADED STUD, use 2 per header pipe, for on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models. Each:
$ 3.95

HCP2941SET8 OEM cylinder head exhaust port THREADED STUDS, set of 8:
$ 24.95


HCP19160 Aftermarket cylinder head exhaust port THREADED STUD, use 2 per header pipe, for on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models. Each:
$ 2.95

HCP19160SET8 Aftermarket cylinder head exhaust port THREADED STUDS, set of 8:
$ 17.95



HCP581 OEM header pipe to above stud SPECIAL TALL FLANGED NUT with the 6mm allen-key drive. Use 2 per header pipe on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models. NOTE: original nuts featured a bright finish, these are now supplied with a dark finish. Each:
$ 3.95

HCP581SET8 OEM header pipe to above stud SPECIAL TALL FLANGED NUT, set of 8:
$ 27.95


HCP26769 Aftermarket header pipe to above stud FLANGED NUT, made from alloy steel with a bright zinc-plated finish. A more affordable option than the factory nuts, but note that these aftermarket nuts are regular-height, and do not feature the hex-drive opening (so you’ll need to use a deep 10mm socket to install them). Use 2 per header pipe on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models, each:
$ 1.95

HCP26769SET8 Aftermarket header pipe to above stud FLANGED NUT, set of 8:
$ 11.95


HCP24409 Aftermarket header pipe to above stud FLANGED NUT, made from super-corrosion resistant 316 stainless steel. Note that these aftermarket nuts are regular-height, and do not feature the hex-drive opening (so you’ll need to use a deep 10mm socket to install them). Use 2 per header pipe on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models, each:
$ 2.95

HCP24409SET8 Aftermarket header pipe to above stud FLANGED NUT, set of 8:
$ 19.95



HCP24431 OEM header pipe INSTALLATION KIT, contains all 8 threaded studs (HCP2941) and special tall flanged nuts (HCP581), do it all at once and get it over with! Use on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models.
$ 49.95

HCP24432 Aftermarket header pipe INSTALLATION KIT, contains all 8 threaded studs (HCP19160) and stainless steel nuts (HCP24409), do it all at once and get it over with! Use on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models.
$ 34.95


HCP577 OEM header pipe large finned, cast aluminum RING NUT, natural finish, use 1 per pipe, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ discontinued


HCP2182 OEM header pipe gas analysis test port BOLT, 6-point hex head alloy steel fastener with a bright finish, use 1 per pipe, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 2.95

HCP22180 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head alloy steel fastener with a dark finish, use 1 per pipe, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.25

HCP22182 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head 18/8 stainless steel fastener with a bright finish, use 1 per pipe, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.75

HCP22183 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head 316 stainless steel fastener with a bright finish, use 1 per pipe, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.95

HCP22181 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head alloy steel fastener has a serrated flange (which eliminates the need for using a lockwasher) and features a dark finish, use 1 per pipe, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.95



HCP2173 OEM header pipe gas analysis test port bolt FLAT WASHER, original bright finish, use 1 per pipe, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.95

HCP6642 Aftermarket header pipe gas analysis test port bolt FLAT WASHER, zinc-plated alloy steel with a bright finish, use 1 per pipe an all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 0.95

HCP6643 Aftermarket header pipe gas analysis test port bolt FLAT WASHER, 18-8 stainless steel, use 1 per pipe an all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.25

HCP25756 Aftermarket header pipe gas analysis test port bolt FLAT WASHER, 316 stainless steel, use 1 per pipe an all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.95

HCP14285 Aftermarket header pipe gas analysis test port bolt FLAT WASHER, black oxide-coated, 18-8 stainless steel, use 1 per pipe an all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.95



HCP2181 OEM header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel with a satin finish (original was bright polished), hex-head bolt, use 1 per pipe, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.95

HCP17123 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 18/8 stainless steel with a bright finish, hex-head bolt, use 1 per pipe, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.95

HCP22191 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 316 stainless steel with a bright finish, hex-head bolt, use 1 per pipe, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$2.25

HCP22189 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel with a yellow zinc-plated finish, hex-head bolt, use 1 per pipe, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.25

HCP17122 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel with a black finish, hex-head bolt, use 1 per pipe, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.50



HCP2537 OEM header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per pipe, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.95

HCP26192 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per pipe, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 0.95

HCP26193 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 1 per pipe, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.25

HCP17110 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, 316 stainless steel, bright finish, use 1 per pipe, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.95

HCP26189 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, black finish, use 1 per pipe, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 2.95



HCP10714 Aftermarket chrome-plated header pipe outlet-to-collector inlet PINCH CLAMP, complete with attaching hardware, use 1 per pipe, for all XJ550, XJ650RJ Seca, XJ650 Turbo, and all 1981-84 XJ750 air-cooled models. NOTE: original clamps are spot-welded onto pipe; spot weld must be broken to remove original clamps! Each:
$ 16.95



HCP3931 OEM collector rear support BOLT, alloy steel, bright finish, use 1 per bike, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 2.95

HCP26191 Aftermarket collector rear support BOLT, alloy steel, bright finish, use 1 per bike, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 2.25


HCP2637 OEM collector rear support RUBBER INSULATOR (damper), use 2 per bike, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 19.95

HCP2632 OEM collector rear SUPPORT BRACKET, use 1 per bike, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 49.95

HCP2635 OEM collector rear support bracket insulator COLLAR, use 1 per bike, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 27.95



HCP3925 OEM collector rear support bracket-to-frame mounting BOLT, alloy steel hex-head bolt with a bright finish, use 2 per bike, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 2.95

HCP17143 Aftermarket collector rear support bracket-to-frame mounting BOLT, steel hex-head bolt with a bright silver-zinc finish, use 2 per bike, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.25

HCP22195 Aftermarket collector rear support bracket-to-frame mounting BOLT, alloy steel hex-head bolt with a bright yellow-zinc finish, use 2 per bike, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.50

HCP17144 Aftermarket collector rear support bracket-to-frame mounting BOLT, alloy steel hex-head bolt with a black finish, use 2 per bike, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.95

HCP17145 Aftermarket collector rear support bracket-to-frame mounting BOLT, 18/8 stainless steel hex-head bolt with a bright finish, use 2 per bike, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.75

HCP22198 Aftermarket collector rear support bracket-to-frame mounting BOLT, 316 stainless steel hex-head bolt with a bright finish, use 2 per bike, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.95

HCP22200 Aftermarket collector rear support bracket-to-frame mounting BOLT, high-strength alloy steel socket head (hex-key) bolt with a black finish, use 2 per bike, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 3.95

HCP22201 Aftermarket collector rear support bracket-to-frame mounting BOLT, alloy steel socket head (hex-key) bolt with a bright finish, use 2 per bike, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 3.95

HCP22202 Aftermarket collector rear support bracket-to-frame mounting BOLT, 18/8 stainless steel socket head (hex-key) bolt with a bright finish, use 2 per bike, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 3.95

HCP24125 Aftermarket collector rear support bracket-to-frame mounting BOLT, 316 stainless steel socket head (hex-key) bolt with a bright finish, use 2 per bike, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 4.95



HCP2537 OEM collector rear support bracket-to-frame mounting bolt FLAT WASHER, alloy steel, bright finish, use 2 per bike, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.95

HCP26192 Aftermarket collector rear support bracket-to-frame mounting bolt FLAT WASHER, alloy steel, bright finish, use 2 per bike, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 0.95

HCP26193 Aftermarket collector rear support bracket-to-frame mounting bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 2 per bike, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.25

HCP17110 Aftermarket collector rear support bracket-to-frame mounting bolt FLAT WASHER, 316 stainless steel, bright finish, use 2 per bike, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.95

HCP26189 Aftermarket collector rear support bracket-to-frame mounting bolt FLAT WASHER, alloy steel, black finish, use 2 per bike, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 2.95



HCP3925 OEM collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel hex-head bolt with a bright finish, use 1 per muffler, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 2.95

HCP17143 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, steel hex-head bolt with a bright silver-zinc finish, use 1 per muffler, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.25

HCP22195 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel hex-head bolt with a bright yellow-zinc finish, use 1 per muffler, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.50

HCP17144 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel hex-head bolt with a black finish, use 1 per muffler, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.95

HCP17145 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 18/8 stainless steel hex-head bolt with a bright finish, use 1 per muffler, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.75

HCP22198 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 316 stainless steel hex-head bolt with a bright finish, use 1 per muffler, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.95

HCP22200 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, high-strength alloy steel socket head (hex-key) bolt with a black finish, use 1 per muffler, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 3.95

HCP22201 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel socket head (hex-key) bolt with a bright finish, use 1 per muffler, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 3.95

HCP22202 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 18/8 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per muffler, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 3.95

HCP24125 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 316 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per muffler, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 4.95



HCP2537 OEM collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per muffler, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.95

HCP26192 Aftermarket collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per muffler, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 0.95

HCP26193 Aftermarket collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 1 per muffler, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.25

HCP17110 Aftermarket collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, 316 stainless steel, bright finish, use 1 per muffler, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.95

HCP26189 Aftermarket collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, alloy steel, black finish, use 1 per muffler, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 2.95



HCP9713 Aftermarket chrome-plated header pipe outlet-to-collector inlet PINCH CLAMP, complete with attaching hardware, use 1 per pipe, for all XJ650RJ/RJC Seca and XJ650 Euro models. NOTE: original clamps are spot-welded onto pipe; spot weld must be broken to remove original clamps! Each:
$ 11.95



HCP3936 OEM muffler-to-rear footpeg bracket mounting FLANGE BOLT, use 1 per side, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 3.95


HCP3946 OEM muffler mounting bracket bolt FLAT WASHER, alloy steel, bright finish, use 1 per side, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 3.95

HCP26196 Aftermarket muffler mounting bracket bolt FLAT WASHER, alloy steel, bright finish, use 1 per side, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 1.95

HCP26197 Aftermarket muffler mounting bracket bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 1 per side, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 2.95

HCP26198 Aftermarket muffler mounting bracket bolt FLAT WASHER, 316 stainless steel, dull finish, use 1 per side, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 3.95


HCP3942 OEM muffler mounting bracket bolt OVAL NUT, use 1 per side, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 19.95

HCP26217 Aftermarket muffler mounting bracket bolt OVAL NUT, use 1 per side, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 11.95



HCP2639 OEM left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used, for all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 12.95

HCP2640 OEM left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used. NOTE: this bumper is approximately 3mm shorter than the original HCP2639 bumper, but will still fit and function properly (and is about 1/2 the price of the correct bumper). Fits all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 7.95

HCP26234 Aftermarket left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used. NOTE: this bumper is approximately 3mm shorter than the original HCP2639 bumper, but will still fit and function properly (and is about 1/2 the price of the correct bumper). Fits all XJ650RJ/RJC Seca and XJ650 Euro models, each:
$ 5.95



XJ650 Turbo models:

HCP2941 OEM cylinder head exhaust port THREADED STUD, use 2 per header pipe, for on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models. Each:
$ 3.95

HCP2941SET8 OEM cylinder head exhaust port THREADED STUDS, set of 8:
$ 24.95


HCP19160 Aftermarket cylinder head exhaust port THREADED STUD, use 2 per header pipe, for on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models. Each:
$ 2.95

HCP19160SET8 Aftermarket cylinder head exhaust port THREADED STUDS, set of 8:
$ 17.95



HCP581 OEM header pipe to above stud SPECIAL TALL FLANGED NUT with the 6mm allen-key drive. Use 2 per header pipe on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models. NOTE: original nuts featured a bright finish, these are now supplied with a dark finish. Each:
$ 3.95

HCP581SET8 OEM header pipe to above stud SPECIAL TALL FLANGED NUT, set of 8:
$ 27.95


HCP26769 Aftermarket header pipe to above stud FLANGED NUT, made from alloy steel with a bright zinc-plated finish. A more affordable option than the factory nuts, but note that these aftermarket nuts are regular-height, and do not feature the hex-drive opening (so you’ll need to use a deep 10mm socket to install them). Use 2 per header pipe on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models, each:
$ 1.95

HCP26769SET8 Aftermarket header pipe to above stud FLANGED NUT, set of 8:
$ 11.95


HCP24409 Aftermarket header pipe to above stud FLANGED NUT, made from super-corrosion resistant 316 stainless steel. Note that these aftermarket nuts are regular-height, and do not feature the hex-drive opening (so you’ll need to use a deep 10mm socket to install them). Use 2 per header pipe on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models, each:
$ 2.95

HCP24409SET8 Aftermarket header pipe to above stud FLANGED NUT, set of 8:
$ 19.95



HCP24431 OEM header pipe INSTALLATION KIT, contains all 8 threaded studs (HCP2941) and special tall flanged nuts (HCP581), do it all at once and get it over with! Use on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models.
$ 49.95

HCP24432 Aftermarket header pipe INSTALLATION KIT, contains all 8 threaded studs (HCP19160) and stainless steel nuts (HCP24409), do it all at once and get it over with! Use on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models.
$ 34.95


HCP578 OEM header pipe large finned, cast aluminum RING NUT, black finish, use 1 per pipe, for all XJ650 Turbo models, each:
$ 49.95



HCP3933 OEM header pipe gas analysis test port BOLT, 6-point hex head alloy steel fastener with a dark finish, use 1 per pipe, 1982 XJ650 Turbo models, each:
$ 2.95

HCP22180 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head alloy steel fastener with a dark finish, use 1 per pipe, 1982 XJ650 Turbo models, each:
$ 1.25

HCP22182 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head 18/8 stainless steel fastener with a bright finish, use 1 per pipe, 1982 XJ650 Turbo models, each:
$ 1.75

HCP22183 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head 316 stainless steel fastener with a bright finish, use 1 per pipe, 1982 XJ650 Turbo models, each:
$ 1.95

HCP22181 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head alloy steel fastener has a serrated flange (which eliminates the need for using a lockwasher) and features a dark finish, use 1 per pipe, 1982 XJ650 Turbo models, each:
$ 1.95


HCP3935 OEM header pipe gas analysis test port BOLT, black finish, 6-point hex-head style, use 1 per pipe on all 1983 XJ650 Turbo models, each:
$ 2.95

HCP22159 Aftermarket header pipe gas analysis test port BOLT, zinc-plated alloy steel, 6-point hex-head style, use 1 per pipe on all 1983 XJ650 Turbo models, each:
$ 1.00

HCP22160 Aftermarket header pipe gas analysis test port BOLT, 18/8 stainless steel, 6-point hex-head style, use 1 per pipe on all 1983 XJ650 Turbo models, each:
$ 1.95

HCP21964 Aftermarket header pipe gas analysis test port BOLT, black-oxide coated alloy steel, socket head (hex-key) style fastener, use 1 per pipe on all 1983 XJ650 Turbo models, each:
$ 1.95



HCP2173 OEM header pipe gas analysis test port bolt FLAT WASHER, original bright finish, use 1 per pipe on all 1982 XJ650 Turbo models, each:
$ 1.95

HCP6642 Aftermarket header pipe gas analysis test port bolt FLAT WASHER, zinc-plated alloy steel with a bright finish, use 1 per pipe on all 1982 XJ650 Turbo models, each:
$ 0.95

HCP6643 Aftermarket header pipe gas analysis test port bolt FLAT WASHER, 18-8 stainless steel, use 1 per pipe on all 1982 XJ650 Turbo models, each:
$ 1.25

HCP25756 Aftermarket header pipe gas analysis test port bolt FLAT WASHER, 316 stainless steel, use 1 per pipe on all 1982 XJ650 Turbo models, each:
$ 1.95

HCP14285 Aftermarket header pipe gas analysis test port bolt FLAT WASHER, black oxide-coated 18-8 stainless steel, use 1 per pipe on all 1982 XJ650 Turbo models, each:
$ 1.95



HCP4108 OEM header pipe gas analysis test port bolt FLAT WASHER, use 1 per pipe, 1983 XJ650 Turbo models, each:
$ 1.00



HCP2181 OEM header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel with a satin finish (original was bright polished), hex-head bolt, use 1 per pipe, for all XJ650 Turbo models, each:
$ 1.95

HCP17123 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 18/8 stainless steel with a bright finish, hex-head bolt, use 1 per pipe, for all XJ650 Turbo models, each:
$ 1.95

HCP22191 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 316 stainless steel with a bright finish, hex-head bolt, use 1 per pipe, for all XJ650 Turbo models, each:
$2.25

HCP22189 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel with a yellow zinc-plated finish, hex-head bolt, use 1 per pipe, for all XJ650 Turbo models, each:
$ 1.25

HCP17122 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel with a black finish, hex-head bolt, use 1 per pipe, for all XJ650 Turbo models, each:
$ 1.50



HCP2537 OEM header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per pipe, for all XJ650 Turbo models, each:
$ 1.95

HCP26192 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per muffler, for all XJ650 Turbo models, each:
$ 0.95

HCP26193 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 1 per muffler, for all XJ650 Turbo models, each:
$ 1.25

HCP17110 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, 316 stainless steel, bright finish, use 1 per muffler, for all XJ650 Turbo models, each:
$ 1.95

HCP26189 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, black finish, use 1 per muffler, for all XJ650 Turbo models, each:
$ 2.95



HCP10714 Aftermarket chrome-plated header pipe outlet-to-collector inlet PINCH CLAMP, complete with attaching hardware, use 1 per pipe, for all XJ550, XJ650RJ Seca, XJ650 Turbo, and all 1981-84 XJ750 air-cooled models. NOTE: original clamps are spot-welded onto pipe; spot weld must be broken to remove original clamps! Each:
$ 16.95



HCP3931 OEM collector rear support BOLT, alloy steel, bright finish, use 1 per bike, for all XJ650 Turbo models, each:
$ 2.95

HCP26191 Aftermarket collector rear support BOLT, alloy steel, bright finish, use 1 per bike, for all XJ650 Turbo models, each:
$ 2.25


HCP2637 OEM collector rear support RUBBER INSULATOR (damper), use 2 per bike, for all XJ650 Turbo models, each:
$ 19.95

HCP2632 OEM collector rear SUPPORT BRACKET, use 1 per bike, for all XJ650 Turbo models, each:
$ 49.95

HCP2635 OEM collector rear support bracket insulator COLLAR, use 1 per bike, for all XJ650 Turbo models, each:
$ 27.95


HCP3925 OEM collector rear support bracket-to-frame mounting BOLT, alloy steel hex-head bolt with a bright finish, use 2 per bike, for all XJ650 Turbo models, each:
$ 2.95

HCP17143 Aftermarket collector rear support bracket-to-frame mounting BOLT, steel hex-head bolt with a bright silver-zinc finish, use 2 per bike, for all XJ650 Turbo models, each:
$ 1.25

HCP22195 Aftermarket collector rear support bracket-to-frame mounting BOLT, alloy steel hex-head bolt with a bright yellow-zinc finish, use 2 per bike, for all XJ650 Turbo models, each:
$ 1.50

HCP17144 Aftermarket collector rear support bracket-to-frame mounting BOLT, alloy steel hex-head bolt with a black finish, use 2 per bike, for all XJ650 Turbo models, each:
$ 1.95

HCP17145 Aftermarket collector rear support bracket-to-frame mounting BOLT, 18/8 stainless steel hex-head bolt with a bright finish, use 2 per bike, for all XJ650 Turbo models, each:
$ 1.75

HCP22198 Aftermarket collector rear support bracket-to-frame mounting BOLT, 316 stainless steel hex-head bolt with a bright finish, use 2 per bike, for all XJ650 Turbo models, each:
$ 1.95

HCP22200 Aftermarket collector rear support bracket-to-frame mounting BOLT, high-strength alloy steel socket head (hex-key) bolt with a black finish, use 2 per bike, for all XJ650 Turbo models, each:
$ 3.95

HCP22201 Aftermarket collector rear support bracket-to-frame mounting BOLT, alloy steel socket head (hex-key) bolt with a bright finish, use 2 per bike, for all XJ650 Turbo models, each:
$ 3.95

HCP22202 Aftermarket collector rear support bracket-to-frame mounting BOLT, 18/8 stainless steel socket head (hex-key) bolt with a bright finish, use 2 per bike, for all XJ650 Turbo models, each:
$ 3.95

HCP24125 Aftermarket collector rear support bracket-to-frame mounting BOLT, 316 stainless steel socket head (hex-key) bolt with a bright finish, use 2 per bike, for all XJ650 Turbo models, each:
$ 4.95


HCP2537 OEM collector rear support bracket-to-frame mounting bolt FLAT WASHER, alloy steel, bright finish, use 2 per bike, for all XJ650 Turbo models, each:
$ 1.95

HCP26192 Aftermarket collector rear support bracket-to-frame mounting bolt FLAT WASHER, alloy steel, bright finish, use 2 per bike, for all XJ650 Turbo models, each:
$ 0.95

HCP26193 Aftermarket collector rear support bracket-to-frame mounting bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 2 per bike, for all XJ650 Turbo models, each:
$ 1.25

HCP17110 Aftermarket collector rear support bracket-to-frame mounting bolt FLAT WASHER, 316 stainless steel, bright finish, use 2 per bike, for all XJ650 Turbo models, each:
$ 1.95

HCP26189 Aftermarket collector rear support bracket-to-frame mounting bolt FLAT WASHER, alloy steel, black finish, use 2 per bike, for all XJ650 Turbo models, each:
$ 2.95



HCP24364 Aftermarket turbocharger MOUNTING HARDWARE KIT, for all XJ650 Turbo models, mounts the turbocharger to the frame. NOTE: the original nuts were 5mm longer than the nuts supplied in this kit, but a pair of 5mm thick spacers are provided to allow proper fitment. This kit contains two each of the special hex-drive chrome-plated "barrel nuts" and a set of spacers.
$ 21.95



HCP6264 OEM exhaust collector outlet-to-turbocharger inlet stud(s) FLANGED NUT, use 2 per bike, for all XJ650 Turbo models, each:
$ 3.95



HCP2942 OEM turbocharger exhaust port(s) THREADED STUD, dark finish, alloy steel. Use in all of the following positions:
- use 2 at the exhaust collector input to the turbo housing
- use 2 for the turbo mounting to the frame
- use 2 for the mounting of the left muffler to the turbo housing exhaust port
For use on all XJ650 Turbo models. Each:
$ 5.95
$ 33.95 per set of 6

HCP25811 Aftermarket turbocharger exhaust port(s) THREADED STUD, dark finish, alloy steel. Use in all of the following positions:
- use 2 at the exhaust collector input to the turbo housing
- use 2 for the turbo mounting to the frame
- use 2 for the mounting of the left muffler to the turbo housing exhaust port
For use on all XJ650 Turbo models. Each:
$ 3.95
$ 22.95 per set of 6

HCP25812 Aftermarket turbocharger exhaust port(s) THREADED STUD, bright finish, 18-8 stainless steel. Use in all of the following positions:
- use 2 at the exhaust collector input to the turbo housing
- use 2 for the turbo mounting to the frame
- use 2 for the mounting of the left muffler to the turbo housing exhaust port
For use on all XJ650 Turbo models. Each:
$ 4.95
$ 28.95 per set of 6



HCP3934 OEM left muffler inlet flange-to-turbo outlet BOLT, alloy steel socket head cap screw with a bright finish, use 1 per bike, for all XJ650 Turbo models. This bolt is used in the forward lower position. Each:
$ 1.95

HCP22192 Aftermarket left muffler inlet flange-to-turbo outlet BOLT, alloy steel socket head cap screw with a bright finish, use 1 per bike, for all XJ650 Turbo models. This bolt is used in the forward lower position. Each:
$ 1.50

HCP22193 Aftermarket left muffler inlet flange-to-turbo outlet BOLT, alloy steel socket head cap screw with a black finish, use 1 per bike, for all XJ650 Turbo models. This bolt is used in the forward lower position. Each:
$ 1.50

HCP23280 Aftermarket left muffler inlet flange-to-turbo outlet BOLT, 18-8 stainless steel socket head cap screw with a bright finish, use 1 per bike, for all XJ650 Turbo models. This bolt is used in the forward lower position. Each:
$ 4.95

HCP22194 Aftermarket left muffler inlet flange-to-turbo outlet BOLT, 316 stainless steel socket head cap screw with a bright finish, use 1 per bike, for all XJ650 Turbo models. This bolt is used in the forward lower position. Each:
$ 4.95

HCP23281 Aftermarket left muffler inlet flange-to-turbo outlet BOLT, magni-coated (dull aluminum finish, ultra-corrosion resistance) alloy steel, socket head cap screw, use 1 per bike, for all XJ650 Turbo models. This bolt is used in the forward lower position. Each:
$ 4.95



HCP2617 OEM left muffler inlet flange-to-turbo outlet housing studs CHROME BARREL NUT. For use with any of the above bolts. Use 2 per bike, for all 1982 XJ650 Turbo models. These nuts are used on the studs in the center (upper) and the lower rear positions. Each:
$ 5.95

HCP3943 OEM left muffler inlet flange-to-turbo outlet housing studs CHROME BARREL NUT. For use with any of the above bolts. Use 2 per bike, for all 1983 XJ650 Turbo models. These nuts are used on the studs in the center (upper) and the lower rear positions. Each:
$ 5.95



HCP7107 OEM right muffler joint pipe-to-turbo housing outlet short BOLT, socket head (hex-key drive) alloy steel fastener with a bright zinc-plated finish. This fastener goes thru the forward hole in the "protector" plate, thru the lower forward hole in the joint pipe’s triangular flange, and then threads into the turbo housing. Use 1 per bike, for all XJ650 Turbo models, each:
$ 1.95

HCP6639 Aftermarket right muffler joint pipe-to-turbo housing outlet short BOLT, socket head (hex-key drive) 18/8 stainless steel fastener with a bright finish. Use 1 per bike, for all XJ650 Turbo models, each:
$ 1.95

HCP24075 Aftermarket right muffler joint pipe-to-turbo housing outlet short BOLT, socket head (hex-key drive) 18/8 stainless steel fastener with a bright finish. Use 1 per bike, for all XJ650 Turbo models, each:
$ 2.25

HCP6640 Aftermarket right muffler joint pipe-to-turbo housing outlet short BOLT, socket head (hex-key drive) black oxide-coated alloy steel fastener. Use 1 per bike, for all XJ650 Turbo models, each:
$ 1.95




HCP8351 OEM right muffler connecting pipe flange-to-turbo outlet housing long BOLT, alloy steel with a black finish, hex-key drive. These bolts go thru the turbo housing; one fits to the upper threaded hole in the joint pipe’s triangular flange, and the other goes thru the joint pipe flange and threads into the (rear) threaded hole in the sheetmetal "protector" plate. Use 2 per bike, for all XJ650 Turbo models, each:
$ 2.95

HCP22185 Aftermarket right muffler connecting pipe flange-to-turbo outlet housing long BOLT, 18/8 stainless steel, hex-key drive, use 1 per bike, for all XJ650 Turbo models, each:
$ 1.25

HCP22186 Aftermarket right muffler connecting pipe flange-to-turbo outlet housing long BOLT, 316 stainless steel, hex-key drive, use 1 per bike, for all XJ650 Turbo models, each:
$ 1.95

HCP22187 Aftermarket right muffler connecting pipe flange-to-turbo outlet housing long BOLT, alloy steel, black finish, hex-key drive, use 1 per bike, for all XJ650 Turbo models, each:
$ 1.95




HCP3925 OEM right muffler joint pipe-to-muffler inlet clamp CINCH BOLT, alloy steel hex-head bolt with a bright finish, use 1 per bike, for all XJ650 Turbo models, each:
$ 2.95

HCP17143 Aftermarket right muffler joint pipe-to-muffler inlet clamp CINCH BOLT, steel hex-head bolt with a bright silver-zinc finish, use 1 per bike, for all XJ650 Turbo models, each:
$ 1.25

HCP22195 Aftermarket right muffler joint pipe-to-muffler inlet clamp CINCH BOLT, alloy steel hex-head bolt with a bright yellow-zinc finish, use 1 per bike, for all XJ650 Turbo models, each:
$ 1.50

HCP17144 Aftermarket right muffler joint pipe-to-muffler inlet clamp CINCH BOLT, alloy steel hex-head bolt with a black finish, use 1 per bike, for all XJ650 Turbo models, each:
$ 1.95

HCP17145 Aftermarket right muffler joint pipe-to-muffler inlet clamp CINCH BOLT, 18/8 stainless steel hex-head bolt with a bright finish, use 1 per bike, for all XJ650 Turbo models, each:
$ 1.75

HCP22198 Aftermarket right muffler joint pipe-to-muffler inlet clamp CINCH BOLT, 316 stainless steel hex-head bolt with a bright finish, use 1 per bike, for all XJ650 Turbo models, each:
$ 1.95

HCP22200 Aftermarket right muffler joint pipe-to-muffler inlet clamp CINCH BOLT, high-strength alloy steel socket head (hex-key) bolt with a black finish, use 1 per bike, for all XJ650 Turbo models, each:
$ 3.95

HCP22201 Aftermarket right muffler joint pipe-to-muffler inlet clamp CINCH BOLT, alloy steel socket head (hex-key) bolt with a bright finish, use 1 per bike, for all XJ650 Turbo models, each:
$ 3.95

HCP22202 Aftermarket right muffler joint pipe-to-muffler inlet clamp CINCH BOLT, 18/8 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per bike, for all XJ650 Turbo models, each:
$ 3.95

HCP24125 Aftermarket right muffler joint pipe-to-muffler inlet clamp CINCH BOLT, 316 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per bike, for all XJ650 Turbo models, each:
$ 4.95


HCP2537 OEM right muffler joint pipe-to-muffler inlet clamp cinch bolt FLAT WASHER, alloy steel, bright finish, for use with any of the above bolts. Use 1 per bike, for all XJ650 Turbo models, each:
$ 1.95

HCP26192 Aftermarket right muffler joint pipe-to-muffler inlet clamp cinch bolt FLAT WASHER, alloy steel, bright finish, for use with any of the above bolts. Use 1 per bike, for all XJ650 Turbo models, each:
$ 0.95

HCP26193 Aftermarket right muffler joint pipe-to-muffler inlet clamp cinch bolt FLAT WASHER, 18/8 stainless steel, bright finish, for use with any of the above bolts. Use 1 per bike, for all XJ650 Turbo models, each:
$ 1.25

HCP17110 Aftermarket right muffler joint pipe-to-muffler inlet clamp cinch bolt FLAT WASHER, 316 stainless steel, bright finish, for use with any of the above bolts. Use 1 per bike, for all XJ650 Turbo models, each:
$ 1.95

HCP26189 Aftermarket right muffler joint pipe-to-muffler inlet clamp cinch bolt FLAT WASHER, alloy steel, black finish, for use with any of the above bolts. Use 1 per bike, for all XJ650 Turbo models, each:
$ 2.95



HCP4956 OEM right muffler, forward position mounting BOLT, alloy steel, socket head cap screw with a bright finish. Mounts the right muffler hanger bracket to the “triangle-shaped” footrest mounting bracket on all XJ650 Turbo models (use 1, on the right side muffler only, forward position). Each:
$ 4.95

HCP21942 Aftermarket right muffler, forward position mounting BOLT, BOLT, alloy steel socket head cap screw with a bright finish. Mounts the right muffler hanger bracket to the “triangle-shaped” footrest mounting bracket on all XJ650 Turbo models (use 1, on the right side muffler only, forward position). Each:
$ 1.75

HCP23282 Aftermarket right muffler, forward position mounting BOLT, 18/8 stainless steel socket head cap screw with a bright finish. Mounts the right muffler hanger bracket to the “triangle-shaped” footrest mounting bracket on all XJ650 Turbo models (use 1, on the right side muffler only, forward position). Each:
$ 2.95

HCP22203 Aftermarket right muffler, forward position mounting BOLT, 316 stainless steel socket head cap screw with a bright finish. Mounts the right muffler hanger bracket to the “triangle-shaped” footrest mounting bracket on all XJ650 Turbo models (use 1, on the right side muffler only, forward position). Each:
$ 3.95

HCP23283 Aftermarket right muffler, forward position mounting BOLT, magni-coated (dull aluminum finish, ultra-corrosion resistance) alloy steel. Mounts the right muffler hanger bracket to the “triangle-shaped” footrest mounting bracket on all XJ650 Turbo models (use 1, on the right side muffler only, forward position). Each:
$ 2.95

HCP21944 Aftermarket right muffler, forward position mounting BOLT, alloy steel socket head cap screw with a black finish. Mounts the right muffler hanger bracket to the “triangle-shaped” footrest mounting bracket on all XJ650 Turbo models (use 1, on the right side muffler only, forward position). Each:
$ 1.95


HCP6264 OEM right muffler, forward position mounting bolt FLANGED NUT, bright finish. Fits XJ650 Turbo models (use 1, on the right side muffler only, forward position). Each:
$ 3.95

HCP16244 Aftermarket right muffler, forward position mounting bolt FLANGED NUT, bright finish. Fits XJ650 Turbo models (use 1, on the right side muffler only, forward position). Each:
$ 3.95




HCP4049 OEM rear footpeg and muffler mounting FLANGED BOLT, use 1 per side, for all XJ650 Turbo models. This bolt secures both the rear footpeg assembly and the muffler to the “triangle-shaped” footrest mounting bracket. Each:
$ 3.95


HCP4034 OEM rear footpeg assembly and muffler mounting bolt FLANGED NUT, bright finish, use 1 per side, for all XJ650 Turbo models, each:
$ 5.95

HCP16245 Aftermarket rear footpeg assembly and muffler mounting bolt FLANGED NUT. Bright finish. Use 1 per side, for all XJ650 Turbo models, each:
$ 2.95

HCP16247 Aftermarket muffler mounting bolt FLANGED NUT. Dark finish. Use 1 per side, for all XJ650 Turbo models, each:
$ 3.95



HCP2639 OEM left side muffler rubber BUMPER, for where the centerstand contacts the muffler when not being used, for all XJ650 Turbo models, each:
$ 12.95

HCP2640 OEM left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used. NOTE: this bumper is approximately 3mm shorter than the original HCP2639 bumper, but will still fit and function properly (and is about 1/2 the price of the correct bumper). Fits all XJ650 Turbo models, each:
$ 7.95

HCP26234 Aftermarket left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used. NOTE: this bumper is approximately 3mm shorter than the original HCP2639 bumper, but will still fit and function properly (and is about 1/2 the price of the correct bumper). Fits all XJ650 Turbo models, each:
$ 5.95



HCP1272 Aftermarket muffler end cap SCREW, use 2 per end cap, alloy steel with black-oxide finish. For all XJ650 Turbo models, each:
$ 1.95

HCP1273 Aftermarket muffler end cap SCREW, use 2 per end cap, 18/8 stainless steel with bright finish. For all XJ650 Turbo models, each:
$ 2.95

HCP24052 Aftermarket muffler end cap SCREW, use 2 per end cap, made from ultra-rust resistant 316 stainless steel with bright finish. For all XJ650 Turbo models, each:
$ 3.95




XJ700 and XJ750-X models:

HCP2941 OEM cylinder head exhaust port THREADED STUD, use 2 per header pipe, for on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models. Each:
$ 3.95

HCP2941SET8 OEM cylinder head exhaust port THREADED STUDS, set of 8:
$ 24.95


HCP19160 Aftermarket cylinder head exhaust port THREADED STUD, use 2 per header pipe, for on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models. Each:
$ 2.95

HCP19160SET8 Aftermarket cylinder head exhaust port THREADED STUDS, set of 8:
$ 17.95



HCP581 OEM header pipe to above stud SPECIAL TALL FLANGED NUT with the 6mm allen-key drive. Use 2 per header pipe on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models. NOTE: original nuts featured a bright finish, these are now supplied with a dark finish. Each:
$ 3.95

HCP581SET8 OEM header pipe to above stud SPECIAL TALL FLANGED NUT, set of 8:
$ 27.95


HCP26769 Aftermarket header pipe to above stud FLANGED NUT, made from alloy steel with a bright zinc-plated finish. A more affordable option than the factory nuts, but note that these aftermarket nuts are regular-height, and do not feature the hex-drive opening (so you’ll need to use a deep 10mm socket to install them). Use 2 per header pipe on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models, each:
$ 1.95

HCP26769SET8 Aftermarket header pipe to above stud FLANGED NUT, set of 8:
$ 11.95


HCP24409 Aftermarket header pipe to above stud FLANGED NUT, made from super-corrosion resistant 316 stainless steel. Note that these aftermarket nuts are regular-height, and do not feature the hex-drive opening (so you’ll need to use a deep 10mm socket to install them). Use 2 per header pipe on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models, each:
$ 2.95

HCP24409SET8 Aftermarket header pipe to above stud FLANGED NUT, set of 8:
$ 19.95



HCP24431 OEM header pipe INSTALLATION KIT, contains all 8 threaded studs (HCP2941) and special tall flanged nuts (HCP581), do it all at once and get it over with! Use on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models.
$ 49.95

HCP24432 Aftermarket header pipe INSTALLATION KIT, contains all 8 threaded studs (HCP19160) and stainless steel nuts (HCP24409), do it all at once and get it over with! Use on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models.
$ 34.95


HCP579 OEM header pipe large finned, cast aluminum RING NUT, use 1 per pipe, all XJ700 air-cooled engines, each:
$ 59.95

HCP580 OEM header pipe large finned, cast aluminum RING NUT, use 1 per pipe, all XJ700-X and XJ750-X water-cooled engines, each:
$ discontinued



HCP3572 OEM header pipe gas analysis test port BOLT, black finish, 6-point hex-head style, use 1 per pipe, for all XJ700 and XJ750-X models, each:
$ 2.95

HCP22159 Aftermarket header pipe gas analysis test port BOLT, zinc-plated alloy steel, 6-point hex-head style, use 1 per pipe, for all XJ700 and XJ750-X models, each:
$ 1.00

HCP22160 Aftermarket header pipe gas analysis test port BOLT, 18/8 stainless steel, 6-point hex-head style, use 1 per pipe, for all XJ700 and XJ750-X models, each:
$ 1.95

HCP21964 Aftermarket header pipe gas analysis test port BOLT, black-oxide coated alloy steel, socket head (hex-key) style fastener, use 1 per pipe, for all XJ700 and XJ750-X models, each:
$ 1.95


HCP2173 OEM header pipe gas analysis test port bolt FLAT WASHER, u original bright finish, se 1 per pipe, for all XJ700 and XJ750-X models, each:
$ 1.95

HCP6642 Aftermarket header pipe gas analysis test port bolt FLAT WASHER, zinc-plated alloy steel with a bright finish, use 1 per pipe on all XJ700 and XJ750-X models, each:
$ 0.95

HCP6643 Aftermarket header pipe gas analysis test port bolt FLAT WASHER, 18-8 stainless steel, use 1 per pipe on all XJ700 and XJ750-X models, each:
$ 1.25

HCP25756 Aftermarket header pipe gas analysis test port bolt FLAT WASHER, 316 stainless steel, use 1 per pipe on all XJ700 and XJ750-X models, each:
$ 1.95

HCP14285 Aftermarket header pipe gas analysis test port bolt FLAT WASHER, black oxide-coated 18-8 stainless steel, use 1 per pipe on all XJ700 and XJ750-X models, each:
$ 1.95



HCP3928 OEM header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel hex-head bolt with a black finish, use 1 per pipe, for all XJ700 and XJ750-X models, each:
$ 2.95

HCP17143 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, steel hex-head bolt with a bright silver-zinc finish, use 1 per pipe, for all XJ700 and XJ750-X models, each:
$ 1.25

HCP22195 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel hex-head bolt with a bright yellow-zinc finish, use 1 per pipe, for all XJ700 and XJ750-X models, each:
$ 1.50

HCP17144 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel hex-head bolt with a black finish, use 1 per pipe, for all XJ700 and XJ750-X models, each:
$ 1.95

HCP17145 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 18/8 stainless steel hex-head bolt with a bright finish, use 1 per pipe, for all XJ700 and XJ750-X models, each:
$ 1.75

HCP22198 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 316 stainless steel hex-head bolt with a bright finish, use 1 per pipe, for all XJ700 and XJ750-X models, each:
$ 1.95

HCP22200 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, high-strength alloy steel socket head (hex-key) bolt with a black finish, use 1 per pipe, for all XJ700 and XJ750-X models, each:
$ 3.95

HCP22201 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel socket head (hex-key) bolt with a bright finish, use 1 per pipe, for all XJ700 and XJ750-X models, each:
$ 3.95

HCP22202 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 18/8 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per pipe, for all XJ700 and XJ750-X models, each:
$ 3.95

HCP24125 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 316 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per pipe, for all XJ700 and XJ750-X models, each:
$ 4.95



HCP3945 OEM header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, black finish, use 1 per pipe, for all XJ700 and XJ750-X models, each:
$ 1.95

HCP26192 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per pipe, for all XJ700 and XJ750-X models, each:
$ 0.95

HCP26193 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 1 per pipe, for all XJ700 and XJ750-X models, each:
$ 1.25

HCP17110 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, 316 stainless steel, bright finish, use 1 per pipe, for all XJ700 and XJ750-X models, each:
$ 1.95

HCP26189 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, black finish, use 1 per pipe, for all XJ700 and XJ750-X models, each:
$ 2.95



HCP9710 Aftermarket chrome-plated header pipe outlet-to-collector inlet PINCH CLAMP, complete with attaching hardware, use 1 per pipe, for all XJ700 and XJ750-X models. NOTE: original clamps are spot-welded onto pipe; spot weld must be broken to remove original clamps! Each:
$ 11.95



HCP3931 OEM collector rear support BOLT, alloy steel, bright finish, use 1 per bike, for all XJ700 and XJ750-X models, each:
$ 2.95

HCP26191 Aftermarket collector rear support BOLT, alloy steel, bright finish, use 1 per bike, for all XJ700 and XJ750-X models, each:
$ 2.25


HCP2637 OEM collector rear support RUBBER INSULATOR (damper), use 2 per bike, for all XJ700 and XJ750-X models, each:
$ 19.95

HCP3736 OEM collector rear SUPPORT BRACKET, use 1 per bike, for all XJ700 and XJ750-X models, each:
$ discontinued

HCP2635 OEM collector rear support insulator COLLAR, use 1 per bike, for all XJ700 and XJ750-X models, each:
$ 27.95



HCP3925 OEM collector rear support bracket-to-frame mounting BOLT, alloy steel hex-head bolt with a bright finish, use 2 per bike, for all XJ700 and XJ750-X models, each:
$ 2.95

HCP17143 Aftermarket collector rear support bracket-to-frame mounting BOLT, steel hex-head bolt with a bright silver-zinc finish, use 2 per bike, for all XJ700 and XJ750-X models, each:
$ 1.25

HCP22195 Aftermarket collector rear support bracket-to-frame mounting BOLT, alloy steel hex-head bolt with a bright yellow-zinc finish, use 2 per bike, for all XJ700 and XJ750-X models, each:
$ 1.50

HCP17144 Aftermarket collector rear support bracket-to-frame mounting BOLT, alloy steel hex-head bolt with a black finish, use 2 per bike, for all XJ700 and XJ750-X models, each:
$ 1.95

HCP17145 Aftermarket collector rear support bracket-to-frame mounting BOLT, 18/8 stainless steel hex-head bolt with a bright finish, use 2 per bike, for all XJ700 and XJ750-X models, each:
$ 1.75

HCP22198 Aftermarket collector rear support bracket-to-frame mounting BOLT, 316 stainless steel hex-head bolt with a bright finish, use 2 per bike, for all XJ700 and XJ750-X models, each:
$ 1.95

HCP22200 Aftermarket collector rear support bracket-to-frame mounting BOLT, high-strength alloy steel socket head (hex-key) bolt with a black finish, use 2 per bike, for all XJ700 and XJ750-X models, each:
$ 3.95

HCP22201 Aftermarket collector rear support bracket-to-frame mounting BOLT, alloy steel socket head (hex-key) bolt with a bright finish, use 2 per bike for all XJ700 and XJ750-X models, each:
$ 3.95

HCP22202 Aftermarket collector rear support bracket-to-frame mounting BOLT, 18/8 stainless steel socket head (hex-key) bolt with a bright finish, use 2 per bike, for all XJ700 and XJ750-X models, each:
$ 3.95

HCP24125 Aftermarket collector rear support bracket-to-frame mounting BOLT, 316 stainless steel socket head (hex-key) bolt with a bright finish, use 2 per bike, for all XJ700 and XJ750-X models, each:
$ 4.95



HCP2537 OEM collector rear support bracket-to-frame mounting bolt FLAT WASHER, alloy steel, bright finish, use 2 per bike, for all XJ700 and XJ750-X models, each:
$ 1.95

HCP26192 Aftermarket collector rear support bracket-to-frame mounting bolt FLAT WASHER, alloy steel, bright finish, use 2 per bike, for all XJ700 and XJ750-X models, each:
$ 0.95

HCP26193 Aftermarket collector rear support bracket-to-frame mounting bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 2 per bike, for all XJ700 and XJ750-X models, each:
$ 1.25

HCP17110 Aftermarket collector rear support bracket-to-frame mounting bolt FLAT WASHER, 316 stainless steel, bright finish, use 2 per bike, for all XJ700 and XJ750-X models, each:
$ 1.95

HCP26189 Aftermarket collector rear support bracket-to-frame mounting bolt FLAT WASHER, alloy steel, black finish, use 2 per bike, for all XJ700 and XJ750-X models, each:
$ 2.95




HCP3925 OEM collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel hex-head bolt with a bright finish, use 1 per muffler, for all XJ700 and XJ750-X models, each:
$ 2.95

HCP17143 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, steel hex-head bolt with a bright silver-zinc finish, use 1 per muffler, for all XJ700 and XJ750-X models, each:
$ 1.25

HCP22195 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel hex-head bolt with a bright yellow-zinc finish, use 1 per muffler, for all XJ700 and XJ750-X models, each:
$ 1.50

HCP17144 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel hex-head bolt with a black finish, use 1 per muffler, for all XJ700 and XJ750-X models, each:
$ 1.95

HCP17145 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 18/8 stainless steel hex-head bolt with a bright finish, use 1 per muffler, for all XJ700 and XJ750-X models, each:
$ 1.75

HCP22198 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 316 stainless steel hex-head bolt with a bright finish, use 1 per muffler, for all XJ700 and XJ750-X models, each:
$ 1.95

HCP22200 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, high-strength alloy steel socket head (hex-key) bolt with a black finish, use 1 per muffler, for all XJ700 and XJ750-X models, each:
$ 3.95

HCP22201 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel socket head (hex-key) bolt with a bright finish, use 1 per muffler, for all XJ700 and XJ750-X models, each:
$ 3.95

HCP22202 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 18/8 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per muffler, for all XJ700 and XJ750-X models, each:
$ 3.95

HCP24125 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 316 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per muffler, for all XJ700 and XJ750-X models, each:
$ 4.95



HCP2537 OEM collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per muffler, for all XJ700 and XJ750-X models, each:
$ 1.95

HCP26192 Aftermarket collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per muffler, for all XJ700 and XJ750-X models, each:
$ 0.95

HCP26193 Aftermarket collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 1 per muffler, for all XJ700 and XJ750-X models, each:
$ 1.25

HCP17110 Aftermarket collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, 316 stainless steel, bright finish, use 1 per muffler, for all XJ700 and XJ750-X models, each:
$ 1.95

HCP26189 Aftermarket collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, alloy steel, black finish, use 1 per muffler, for all XJ700 and XJ750-X models, each:
$ 2.95



HCP9711 Aftermarket chrome-plated collector-outlet-to-muffler inlet PINCH CLAMP, complete with attaching hardware, use 1 per pipe, for all XJ700 and XJ750-X models. NOTE: original clamps are spot-welded onto pipe; spot weld must be broken to remove original clamps! Each:
$ 11.95



HCP3939 OEM muffler-to-rear footpeg bracket mounting FLANGE BOLT, alloy steel, socket head cap screw with a black finish, use 1 per side, for all XJ700 and XJ750-X models, each:
$ 2.95

HCP22204 Aftermarket muffler-to-rear footpeg bracket mounting FLANGE BOLT, alloy steel, socket head cap screw with a black finish, use 1 per side, for all XJ700 and XJ750-X models, each:
$ 1.75

HCP16262 Aftermarket muffler-to-rear footpeg bracket mounting FLANGE BOLT, alloy steel, socket head cap screw with a bright finish, use 1 per side, for all XJ700 and XJ750-X models, each:
$ 1.95


HCP3947 OEM muffler mounting bracket bolt FLAT WASHER, use 1 per side, for all XJ700 and XJ750-X models, each:
$ 4.75


HCP2639 OEM left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used, for all XJ700 and XJ750-X models, each:
$ 12.95

HCP2640 OEM left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used. NOTE: this bumper is approximately 3mm shorter than the original HCP2639 bumper, but will still fit and function properly (and is about 1/2 the price of the correct bumper). Fits all XJ700 and XJ750-X models, each:
$ 7.95

HCP26234 Aftermarket left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used. NOTE: this bumper is approximately 3mm shorter than the original HCP2639 bumper, but will still fit and function properly (and is about 1/2 the price of the correct bumper). Fits all XJ700 and XJ750-X models, each:
$ 5.95



HCP15021 Aftermarket frame tube NOISE EMISSIONS CERTIFICATION DECAL, white decal with black wording provides model-specific information stating that the bike conforms to federal nose level standards. Used on all XJ700 water-cooled models on the left upper frame tube, just behind the steering headpipe tube.
$ 10.95

HCP15118 Aftermarket frame tube NOISE EMISSIONS CERTIFICATION DECAL, white decal with black wording provides model-specific information stating that the bike conforms to federal nose level standards. Used on all XJ700 air-cooled models on the left upper frame tube, just behind the steering headpipe tube.
$ 10.95



all air-cooled XJ750 Maxim, Midnight Maxim, 1981-83 XJ750 Seca, and XJ750 Euro models:

HCP2941 OEM cylinder head exhaust port THREADED STUD, use 2 per header pipe, for on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models. Each:
$ 3.95

HCP2941SET8 OEM cylinder head exhaust port THREADED STUDS, set of 8:
$ 24.95


HCP19160 Aftermarket cylinder head exhaust port THREADED STUD, use 2 per header pipe, for on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models. Each:
$ 2.95

HCP19160SET8 Aftermarket cylinder head exhaust port THREADED STUDS, set of 8:
$ 17.95



HCP581 OEM header pipe to above stud SPECIAL TALL FLANGED NUT with the 6mm allen-key drive. Use 2 per header pipe on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models. NOTE: original nuts featured a bright finish, these are now supplied with a dark finish. Each:
$ 3.95

HCP581SET8 OEM header pipe to above stud SPECIAL TALL FLANGED NUT, set of 8:
$ 27.95


HCP26769 Aftermarket header pipe to above stud FLANGED NUT, made from alloy steel with a bright zinc-plated finish. A more affordable option than the factory nuts, but note that these aftermarket nuts are regular-height, and do not feature the hex-drive opening (so you’ll need to use a deep 10mm socket to install them). Use 2 per header pipe on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models, each:
$ 1.95

HCP26769SET8 Aftermarket header pipe to above stud FLANGED NUT, set of 8:
$ 11.95


HCP24409 Aftermarket header pipe to above stud FLANGED NUT, made from super-corrosion resistant 316 stainless steel. Note that these aftermarket nuts are regular-height, and do not feature the hex-drive opening (so you’ll need to use a deep 10mm socket to install them). Use 2 per header pipe on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models, each:
$ 2.95

HCP24409SET8 Aftermarket header pipe to above stud FLANGED NUT, set of 8:
$ 19.95



HCP24431 OEM header pipe INSTALLATION KIT, contains all 8 threaded studs (HCP2941) and special tall flanged nuts (HCP581), do it all at once and get it over with! Use on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models.
$ 49.95

HCP24432 Aftermarket header pipe INSTALLATION KIT, contains all 8 threaded studs (HCP19160) and stainless steel nuts (HCP24409), do it all at once and get it over with! Use on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models.
$ 34.95


HCP579 OEM header pipe large finned, cast aluminum RING NUT, use 1 per pipe, natural finish, for all XJ750 Maxim, 1981-83 XJ750 Seca, and XJ750 Euro models. NOTE: can be used on the XJ750 Midnight Maxim models, but they were originally black. Each:
$ 59.95



HCP2182 OEM header pipe gas analysis test port BOLT, 6-point hex head alloy steel fastener with a bright finish, use 1 per pipe, for all 1982 XJ750 Maxim and all 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 2.95

HCP22180 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head alloy steel fastener with a dark finish, use 1 per pipe, for all 1982 XJ750 Maxim and all 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 1.25

HCP22182 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head 18/8 stainless steel fastener with a bright finish, use 1 per pipe, for all 1982 XJ750 Maxim and all 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 1.75

HCP22183 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head 316 stainless steel fastener with a bright finish, use 1 per pipe, for all 1982 XJ750 Maxim and all 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 1.95

HCP22181 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head alloy steel fastener has a serrated flange (which eliminates the need for using a lockwasher) and features a dark finish, use 1 per pipe, for all 1982 XJ750 Maxim and all 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 1.95


HCP3572 OEM header pipe gas analysis test port BOLT, black finish, 6-point hex-head style, use 1 per pipe, for use on all 1983 XJ750 Maxim and Midnight Maxim models, each:
$ 2.95

HCP22159 Aftermarket header pipe gas analysis test port BOLT, zinc-plated alloy steel, 6-point hex-head style, use 1 per pipe, for use on all 1983 XJ750 Maxim and Midnight Maxim models, each:
$ 1.00

HCP22160 Aftermarket header pipe gas analysis test port BOLT, 18/8 stainless steel, 6-point hex-head style, use 1 per pipe, for use on all 1983 XJ750 Maxim and Midnight Maxim models, each:
$ 1.95

HCP21964 Aftermarket header pipe gas analysis test port BOLT, black-oxide coated alloy steel, socket head (hex-key) style fastener, use 1 per pipe, for use on all 1983 XJ750 Maxim and Midnight Maxim models, each:
$ 1.95



HCP2173 OEM header pipe gas analysis test port bolt FLAT WASHER, original bright finish, use 1 per pipe, XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 1.95

HCP1869 OEM header pipe gas analysis test port bolt FLAT WASHER, black-oxide finish, use 1 per pipe, XJ750 Midnight Maxim models, each:
$ 1.95

HCP6642 Aftermarket header pipe gas analysis test port bolt FLAT WASHER, zinc-plated alloy steel with a bright finish, use 1 per pipe on all XJ750 Maxim, XJ750 Midnight Maxim, and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 0.95

HCP6643 Aftermarket header pipe gas analysis test port bolt FLAT WASHER, 18-8 stainless steel, use 1 per pipe on all XJ750 Maxim, XJ750 Midnight Maxim, and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 1.25

HCP25756 Aftermarket header pipe gas analysis test port bolt FLAT WASHER, 316 stainless steel, use 1 per pipe on all XJ750 Maxim, XJ750 Midnight Maxim, and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 1.95

HCP14285 Aftermarket header pipe gas analysis test port bolt FLAT WASHER, black oxide-coated 18-8 stainless steel, use 1 per pipe on all XJ750 Maxim, XJ750 Midnight Maxim, and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 1.95



HCP3927 OEM header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel with a black finish, hex-head bolt, use 1 per pipe, for all XJ750 Maxim, Midnight Maxim, 1981-83 XJ750 Seca, and XJ750 Euro models, each:
$ 2.95

HCP17123 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 18/8 stainless steel with a bright finish, hex-head bolt, use 1 per pipe, for all XJ750 Maxim, Midnight Maxim, 1981-83 XJ750 Seca, and XJ750 Euro models, each:
$ 1.95

HCP22191 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 316 stainless steel with a bright finish, hex-head bolt, use 1 per pipe, for all XJ750 Maxim, Midnight Maxim, 1981-83 XJ750 Seca, and XJ750 Euro models, each:
$2.25

HCP22189 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel with a yellow zinc-plated finish, hex-head bolt, use 1 per pipe, for all XJ750 Maxim, Midnight Maxim, 1981-83 XJ750 Seca, and XJ750 Euro models, each:
$ 1.25

HCP17122 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel with a black finish, hex-head bolt, use 1 per pipe, for all XJ750 Maxim, Midnight Maxim, 1981-83 XJ750 Seca, and XJ750 Euro models, each:
$ 1.50



HCP3945 OEM header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, black finish, use 1 per pipe, for all XJ750 Maxim, Midnight Maxim, 1981-83 XJ750 Seca, and XJ750 Euro models, each:
$ 1.95

HCP26192 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per pipe, for all XJ750 Maxim, Midnight Maxim, 1981-83 XJ750 Seca, and XJ750 Euro models, each:
$ 0.95

HCP26193 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 1 per pipe, for all XJ750 Maxim, Midnight Maxim, 1981-83 XJ750 Seca, and XJ750 Euro models, each:
$ 1.25

HCP17110 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, 316 stainless steel, bright finish, use 1 per pipe, for all XJ750 Maxim, Midnight Maxim, 1981-83 XJ750 Seca, and XJ750 Euro models, each:
$ 1.95

HCP26189 Aftermarket header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, black finish, use 1 per pipe, for all XJ750 Maxim, Midnight Maxim, 1981-83 XJ750 Seca, and XJ750 Euro models, each:
$ 2.95



HCP10714 Aftermarket chrome-plated header pipe outlet-to-collector inlet PINCH CLAMP, complete with attaching hardware, use 1 per pipe, for all XJ750 Maxim, Midnight Maxim, 1981-83 XJ750 Seca, and XJ750 Euro models. NOTE: original clamps are spot-welded onto pipe; spot weld must be broken to remove original clamps! Each:
$ 16.95



HCP3931 OEM collector rear support BOLT, alloy steel, bright finish, use 1 per bike, for all XJ750 Maxim, Midnight Maxim, 1981-83 XJ750 Seca, and XJ750 Euro models, each:
$ 2.95

HCP26191 Aftermarket collector rear support BOLT, alloy steel, bright finish, use 1 per bike, for all XJ750 Maxim, Midnight Maxim, 1981-83 XJ750 Seca, and XJ750 Euro models, each:
$ 2.25


HCP2637 OEM collector rear support RUBBER INSULATOR (damper), use 2 per bike, for all XJ750 Maxim, Midnight Maxim, 1981-83 XJ750 Seca, and XJ750 Euro models, each:
$ 19.95

HCP2632 OEM SUPPORT BRACKET, use 1 per bike, for all XJ750 Maxim, Midnight Maxim, 1981-83 XJ750 Seca, and XJ750 Euro models, each:
$ 49.95

HCP2635 OEM collector rear support insulator COLLAR, use 1 per bike, for all XJ750 Maxim, Midnight Maxim, 1981-83 XJ750 Seca, and XJ750 Euro models, each:
$ 27.95



HCP3925 OEM collector rear support bracket-to-frame mounting BOLT, alloy steel hex-head bolt with a bright finish, use 2 per bike, for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 2.95

HCP3928 OEM collector rear support bracket-to-frame mounting BOLT, alloy steel hex-head bolt with a black finish, use 2 per bike, for all XJ750 Midnight Maxim models, each:
$ 2.95

HCP17143 Aftermarket collector rear support bracket-to-frame mounting BOLT, steel hex-head bolt with a bright silver-zinc finish, use 2 per bike, for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 1.25

HCP22195 Aftermarket collector rear support bracket-to-frame mounting BOLT, alloy steel hex-head bolt with a bright yellow-zinc finish, use 2 per bike, for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 1.50

HCP17144 Aftermarket collector rear support bracket-to-frame mounting BOLT, alloy steel hex-head bolt with a black finish, use 2 per bike, for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 1.95

HCP17145 Aftermarket collector rear support bracket-to-frame mounting BOLT, 18/8 stainless steel hex-head bolt with a bright finish, use 2 per bike, for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 1.75

HCP22198 Aftermarket collector rear support bracket-to-frame mounting BOLT, 316 stainless steel hex-head bolt with a bright finish, use 2 per bike, for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 1.95

HCP22200 Aftermarket collector rear support bracket-to-frame mounting BOLT, high-strength alloy steel socket head (hex-key) bolt with a black finish, use 2 per bike, for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 3.95

HCP22201 Aftermarket collector rear support bracket-to-frame mounting BOLT, alloy steel socket head (hex-key) bolt with a bright finish, use 2 per bike, for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 3.95

HCP22202 Aftermarket collector rear support bracket-to-frame mounting BOLT, 18/8 stainless steel socket head (hex-key) bolt with a bright finish, use 2 per bike, for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 3.95

HCP24125 Aftermarket collector rear support bracket-to-frame mounting BOLT, 316 stainless steel socket head (hex-key) bolt with a bright finish, use 2 per bike, for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 4.95



HCP2537 OEM collector rear support bracket-to-frame mounting bolt FLAT WASHER, alloy steel, bright finish, for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, use 2 per bike, each:
$ 1.95

HCP3945 OEM collector rear support bracket-to-frame mounting bolt FLAT WASHER, alloy steel, black finish, for XJ750 Midnight Maxim models, use 2 per bike, each:
$ 1.95

HCP26192 Aftermarket collector rear support bracket-to-frame mounting bolt FLAT WASHER, alloy steel, bright finish, for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, use 2 per bike, each:
$ 0.95

HCP26193 Aftermarket collector rear support bracket-to-frame mounting bolt FLAT WASHER, 18/8 stainless steel, bright finish, for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, use 2 per bike, each:
$ 1.25

HCP17110 Aftermarket collector rear support bracket-to-frame mounting bolt FLAT WASHER, 316 stainless steel, bright finish, for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, use 2 per bike, each:
$ 1.95

HCP26189 Aftermarket collector rear support bracket-to-frame mounting bolt FLAT WASHER, alloy steel, black finish, for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, use 2 per bike, each:
$ 2.95



HCP3925 OEM collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel hex-head bolt with a bright finish, use 1 per muffler for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 2.95

HCP17143 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, steel hex-head bolt with a bright silver-zinc finish, use 1 per muffler for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 1.25

HCP22195 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel hex-head bolt with a bright yellow-zinc finish, use 1 per muffler for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 1.50

HCP17144 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel hex-head bolt with a black finish, use 1 per muffler for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 1.95

HCP17145 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 18/8 stainless steel hex-head bolt with a bright finish, use 1 per muffler for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 1.75

HCP22198 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 316 stainless steel hex-head bolt with a bright finish, use 1 per muffler for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 1.95

HCP22200 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, high-strength alloy steel socket head (hex-key) bolt with a black finish, use 1 per muffler for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 3.95

HCP22201 Aftermarket collector (rear) frame bracket-to-frame mounting BOLT, alloy steel socket head (hex-key) bolt with a bright finish, use 1 per muffler for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 3.95

HCP22202 Aftermarket collector (rear) frame bracket-to-frame mounting BOLT, 18/8 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per muffler for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 3.95

HCP24125 Aftermarket collector (rear) frame bracket-to-frame mounting BOLT, 316 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per muffler for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 4.95



HCP3928 OEM collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel hex-head bolt with a black finish, use 1 per muffler on all XJ750 Midnight Maxim models, each:
$ 2.95

HCP17143 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, steel hex-head bolt with a bright silver-zinc finish, use 1 per muffler on all XJ750 Midnight Maxim models, each:
$ 1.25

HCP22195 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel hex-head bolt with a bright yellow-zinc finish, use 1 per muffler on all XJ750 Midnight Maxim models, each:
$ 1.50

HCP17144 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel hex-head bolt with a black finish, use 1 per muffler on all XJ750 Midnight Maxim models, each:
$ 1.95

HCP17145 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 18/8 stainless steel hex-head bolt with a bright finish, use 1 per muffler on all XJ750 Midnight Maxim models, each:
$ 1.75

HCP22198 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 316 stainless steel hex-head bolt with a bright finish, use 1 per muffler on all XJ750 Midnight Maxim models, each:
$ 1.95

HCP22200 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, high-strength alloy steel socket head (hex-key) bolt with a black finish, use 1 per muffler on all XJ750 Midnight Maxim models, each:
$ 3.95

HCP22201 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel socket head (hex-key) bolt with a bright finish, use 1 per muffler on all XJ750 Midnight Maxim models, each:
$ 3.95

HCP22202 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 18/8 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per muffler on all XJ750 Midnight Maxim models, each:
$ 3.95

HCP24125 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 316 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per muffler on all XJ750 Midnight Maxim models, each:
$ 4.95



HCP2264 OEM collector cover-to-clamp (rear) pinch clamp SCREW, panhead phillips-drive alloy steel with a bright zinc-plated finish. For all 1981-83 XJ750 Seca and XJ750 Euro models, use 1 per muffler, each:
$ 2.95

HCP2781N Aftermarket collector cover-to-clamp (rear) pinch clamp SCREW, panhead phillips-drive alloy steel with a bright zinc-plated finish. For all 1981-83 XJ750 Seca and XJ750 Euro models, use 1 per muffler, each:
$ 1.50

HCP231N Aftermarket collector cover-to-clamp (rear) pinch clamp SCREW, panhead phillips-drive 18/8 stainless steel with a bright finish. For all 1981-83 XJ750 Seca and XJ750 Euro models, use 1 per muffler, each:
$ 1.95

HCP24070 Aftermarket collector cover-to-clamp (rear) pinch clamp SCREW, panhead phillips-drive 316 stainless steel with a bright finish. For all 1981-83 XJ750 Seca and XJ750 Euro models, use 1 per muffler, each:
$ 2.50



HCP2173 OEM collector cover-to-clamp (rear) pinch clamp screw FLAT WASHER, for all 1981-83 XJ750 Seca and XJ750 Euro models, use 1 per muffler, original bright finish, each:
$ 1.95

HCP6642 Aftermarket collector cover-to-clamp (rear) pinch clamp screw FLAT WASHER, zinc-plated alloy steel with a natural finish, for all 1981-83 XJ750 Seca and XJ750 Euro models, use 1 per muffler, each:
$ 0.95

HCP6643 Aftermarket collector cover-to-clamp (rear) pinch clamp screw FLAT WASHER, 18-8 stainless steel with a natural finish, for all 1981-83 XJ750 Seca and XJ750 Euro models, use 1 per muffler, each:
$ 1.25

HCP25756 Aftermarket collector cover-to-clamp (rear) pinch clamp screw FLAT WASHER, 316 stainless steel with a natural finish, for all 1981-83 XJ750 Seca and XJ750 Euro models, use 1 per muffler, each:
$ 1.95

HCP14285 Aftermarket collector cover-to-clamp (rear) pinch clamp screw FLAT WASHER, black oxide-coated 18-8stainless steel, for all 1981-83 XJ750 Seca and XJ750 Euro models, use 1 per muffler, each:
$ 1.95



HCP2537 OEM collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, for all XJ750 Maxim and 1981-83 XJ750 Seca and XJ750 Euro models, use 1 per muffler, each:
$ 1.95

HCP3945 OEM collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, alloy steel, black finish, for XJ750 Midnight Maxim models, use 1 per muffler, each:
$ 1.95

HCP26192 Aftermarket collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, for all XJ750 Maxim and Midnight Maxim models, and all 1981-83 XJ750 Seca and XJ750 Euro models, use 2 per bike, each:
$ 0.95

HCP26193 Aftermarket collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, 18/8 stainless steel, bright finish, for all XJ750 Maxim and Midnight Maxim models, and all 1981-83 XJ750 Seca and XJ750 Euro models, use 2 per bike, each:
$ 1.25

HCP17110 Aftermarket collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, 316 stainless steel, bright finish, for all XJ750 Maxim and Midnight Maxim models, and all 1981-83 XJ750 Seca and XJ750 Euro models, use 2 per bike, each:
$ 1.95

HCP26189 Aftermarket collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, alloy steel, black finish, for all XJ750 Maxim and Midnight Maxim models, and all 1981-83 XJ750 Seca and XJ750 Euro models, use 2 per bike, each:
$ 2.95



HCP9713 Aftermarket chrome-plated header pipe outlet-to-collector inlet PINCH CLAMP, complete with attaching hardware, use 1 per pipe. NOTE: original clamps are spot-welded onto pipe; spot weld must be broken to remove original clamps! Fits all XJ750 Maxim, Midnight Maxim, XJ750 Euro, and 1981-83 XJ750 Seca models. Each:
$ 11.95



HCP22819 OEM muffler mounting RUBBER DAMPER, helps prevents vibration and a “squeaky” exhaust system. Use 1 per side, this round hard rubber bushing presses into the rear footrest bracket. For all 1984-85 FJ600, 1992-98 XJ600 Seca II, 1982 XJ750 Maxim, and all 1978-80 XS1100 Standard models. Each:
$ 7.95

HCP22820 OEM muffler mounting bolt rubber damper metal SLEEVE. Use 1 per footrest. For all 1984-85 FJ600, 1992-98 XJ600 Seca II, 1982 XJ750 Maxim and 1978-80 XS1100 Standard models. Each:
$ 8.95


HCP24634 Aftermarket muffler mounting bolt RUBBER DAMPER, helps prevents vibration and a “squeaky” exhaust system. Use 1 per side, this round hard rubber bushing bolts into the rear footrest bracket. For all 1983 XJ750 Maxim and Midnight Maxim models. Each:
$ 22.95


HCP8480 OEM muffler mounting RETAINING BOLT, secures the damper to the footrest bracket. Bright finish, alloy steel socket head, allen-drive. Use 2 per damper (4 per bike) on all 1983 XJ750 Maxim models. Each:
$ 2.25

HCP548 OEM muffler mounting RETAINING BOLT, secures the damper to the footrest bracket. Dark finish, alloy steel socket head, allen-drive. Use 2 per damper (4 per bike) on all 1983 XJ750 Midnight Maxim models. Each:
$ 2.50

HCP2424 Aftermarket muffler mounting RETAINING BOLT, secures the damper to the footrest bracket. Black oxide coated alloy steel socket head, allen-drive. Use 2 per damper (4 per bike) on all 1983 XJ750 Midnight Maxim models. Each:
$ 1.95

HCP2423 Aftermarket muffler mounting RETAINING BOLT, secures the damper to the footrest bracket. bright 18-8 stainless steel socket head, allen-drive. Use 2 per damper (4 per bike) on all 1983 XJ750 Midnight Maxim models. Each:
$ 1.50



HCP3931 OEM muffler mounting FLANGE BOLT, alloy steel, bright finish, for all 1982 XJ750 Maxim and models, use 1 per side. This bolt goes thru the muffler mounting rubber damper and sleeve. Each:
$ 2.95

HCP26191 Aftermarket muffler mounting BOLT, alloy steel, bright finish, for all 1982 XJ750 Maxim and models, use 1 per side. This bolt goes thru the muffler mounting rubber damper and sleeve. Each:
$ 2.25


HCP3938 OEM muffler mounting SHOULDER BOLT, for all 1983 XJ750 Maxim and Midnight Maxim models, use 1 per side. This bolt goes thru the muffler mounting rubber damper. Each:
$ 11.95


HCP3937 OEM muffler mounting BOLT, alloy steel, socket head cap screw with a black finish, all 1981-83 XJ750 Seca and XJ750 Euro models, use 1 per side, each:
$ 3.95

HCP22207 Aftermarket muffler mounting FLANGE BOLT, alloy steel, socket head cap screw with a black finish, all 1981-83 XJ750 Seca and XJ750 Euro models, use 1 per side, each:
$ 1.95


HCP3946 OEM muffler mounting bolt FLAT WASHER, alloy steel, bright finish fits 1982 XJ750 Maxim models, use 1 per side, each:
$ 3.95

HCP26196 Aftermarket muffler mounting bolt FLAT WASHER, alloy steel, bright finish fits 1982 XJ750 Maxim models, use 1 per side, each:
$ 1.95

HCP26197 Aftermarket muffler mounting bolt FLAT WASHER, 18/8 stainless steel, bright finish fits 1982 XJ750 Maxim models, use 1 per side, each:
$ 2.95

HCP26198 Aftermarket muffler mounting bolt FLAT WASHER, 316 stainless steel, dull finish fits 1982 XJ750 Maxim models, use 1 per side, each:
$ 3.95


HCP3942 OEM muffler mounting bolt OVAL NUT, use 1 per side, for all XJ750 Maxim, Midnight Maxim, 1981-83 XJ750 Seca, and XJ750 Euro models, each:
$ 19.95

HCP26217 Aftermarket muffler mounting bracket bolt OVAL NUT, use 1 per side, for all XJ750 Maxim, Midnight Maxim, 1981-83 XJ750 Seca, and XJ750 Euro models, each:
$ 11.95



HCP2639 OEM left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used, for all 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 12.95

HCP2640 OEM left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used. NOTE: this bumper is approximately 3mm shorter than the original HCP2639 bumper, but will still fit and function properly (and is about 1/2 the price of the correct bumper). Fits all 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 7.95

HCP26234 Aftermarket left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used. NOTE: this bumper is approximately 3mm shorter than the original HCP2639 bumper, but will still fit and function properly (and is about 1/2 the price of the correct bumper). Fits all 1981-83 XJ750 Seca and XJ750 Euro models, each:
$ 5.95



HCP2639 OEM left side muffler rubber BUMPER, for where the centerstand and the kickstand contacts the muffler when not being used, for all XJ750 Maxim and XJ750 Midnight Maxim models, use 2 per bike, each:
$ 12.95

HCP2640 OEM left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used. NOTE: this bumper is approximately 3mm shorter than the original HCP2639 bumper, but will still fit and function properly (and is about 1/2 the price of the correct bumper). Fits all XJ750 Maxim and XJ750 Midnight Maxim models, use 2 per bike, each:
$ 7.95

HCP26234 Aftermarket left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used. NOTE: this bumper is approximately 3mm shorter than the original HCP2639 bumper, but will still fit and function properly (and is about 1/2 the price of the correct bumper). Fits all XJ750 Maxim and XJ750 Midnight Maxim models, use 2 per bike, each:
$ 5.95




XJ900RK, RL, N/FN, and F models:

HCP2941 OEM cylinder head exhaust port THREADED STUD, use 2 per header pipe, for on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models. Each:
$ 3.95

HCP2941SET8 OEM cylinder head exhaust port THREADED STUDS, set of 8:
$ 24.95


HCP19160 Aftermarket cylinder head exhaust port THREADED STUD, use 2 per header pipe, for on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models. Each:
$ 2.95

HCP19160SET8 Aftermarket cylinder head exhaust port THREADED STUDS, set of 8:
$ 17.95



HCP581 OEM header pipe to above stud SPECIAL TALL FLANGED NUT with the 6mm allen-key drive. Use 2 per header pipe on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models. NOTE: original nuts featured a bright finish, these are now supplied with a dark finish. Each:
$ 3.95

HCP581SET8 OEM header pipe to above stud SPECIAL TALL FLANGED NUT, set of 8:
$ 27.95


HCP26769 Aftermarket header pipe to above stud FLANGED NUT, made from alloy steel with a bright zinc-plated finish. A more affordable option than the factory nuts, but note that these aftermarket nuts are regular-height, and do not feature the hex-drive opening (so you’ll need to use a deep 10mm socket to install them). Use 2 per header pipe on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models, each:
$ 1.95

HCP26769SET8 Aftermarket header pipe to above stud FLANGED NUT, set of 8:
$ 11.95


HCP24409 Aftermarket header pipe to above stud FLANGED NUT, made from super-corrosion resistant 316 stainless steel. Note that these aftermarket nuts are regular-height, and do not feature the hex-drive opening (so you’ll need to use a deep 10mm socket to install them). Use 2 per header pipe on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models, each:
$ 2.95

HCP24409SET8 Aftermarket header pipe to above stud FLANGED NUT, set of 8:
$ 19.95



HCP24431 OEM header pipe INSTALLATION KIT, contains all 8 threaded studs (HCP2941) and special tall flanged nuts (HCP581), do it all at once and get it over with! Use on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models.
$ 49.95

HCP24432 Aftermarket header pipe INSTALLATION KIT, contains all 8 threaded studs (HCP19160) and stainless steel nuts (HCP24409), do it all at once and get it over with! Use on all XJ550, 1984-85 FJ600, 1986-88 FZ600, 1986-90 YX600 Radian models, all XJ650 models, all XJ700 models, all XJ750 models, and all XJ900RK, RL, N/FN, and F models.
$ 34.95


HCP580 OEM header pipe large finned, cast aluminum RING NUT, use 1 per pipe, for all XJ900RK, RL, N/FN, and F models, each:
$ discontinued



HCP3572 OEM collector gas analysis test port BOLT, black finish, 6-point hex-head style, use 1 per pipe, for all XJ900RK, RL, N/FN, and F models, each:
$ 2.95

HCP22159 Aftermarket header pipe gas analysis test port BOLT, zinc-plated alloy steel, 6-point hex-head style, use 1 per pipe, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.00

HCP22160 Aftermarket header pipe gas analysis test port BOLT, 18/8 stainless steel, 6-point hex-head style, use 1 per pipe, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.95

HCP21964 Aftermarket header pipe gas analysis test port BOLT, black-oxide coated alloy steel, socket head (hex-key) style fastener, use 1 per pipe, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.95



HCP2173 OEM collector gas analysis test port bolt FLAT WASHER, use 1 per pipe on all XJ900RK, RL, N/FN, and F models, original bright finish, each:
$ 1.95

HCP6642 OEM collector gas analysis test port bolt FLAT WASHER, zinc-plated alloy steel with a natural finish, use 1 per pipe on all XJ900RK, RL, N/FN, and F models, each:
$ 0.95

HCP6643 OEM collector gas analysis test port bolt FLAT WASHER, 18-8 stainless steel with a natural finish, use 1 per pipe on all XJ900RK, RL, N/FN, and F models, each:
$ 1.25

HCP25756 OEM collector gas analysis test port bolt FLAT WASHER, 316 stainless steel with a natural finish, use 1 per pipe on all XJ900RK, RL, N/FN, and F models, each:
$ 1.95

HCP14285 OEM collector gas analysis test port bolt FLAT WASHER, black oxide-coated 18-8 stainless steel, use 1 per pipe on all XJ900RK, RL, N/FN, and F models, each:
$ 1.95



HCP3925 OEM header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel hex-head bolt with a bright finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 2.95

HCP17143 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, steel hex-head bolt with a bright silver-zinc finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.25

HCP22195 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel hex-head bolt with a bright yellow-zinc finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.50

HCP17144 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel hex-head bolt with a black finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.95

HCP17145 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 18/8 stainless steel hex-head bolt with a bright finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.75

HCP22198 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 316 stainless steel hex-head bolt with a bright finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.95

HCP22200 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, high-strength alloy steel socket head (hex-key) bolt with a black finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 3.95

HCP22201 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel socket head (hex-key) bolt with a bright finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 3.95

HCP22202 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 18/8 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 3.95

HCP24125 Aftermarket header pipe outlet-to-collector inlet pinch clamp BOLT, 316 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 4.95



HCP2537 OEM header pipe outlet-to-collector inlet clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.95

HCP26192 Aftermarket header pipe outlet-to-collector inlet clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 0.95

HCP26193 Aftermarket header pipe outlet-to-collector inlet clamp bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.25

HCP17110 Aftermarket header pipe outlet-to-collector inlet clamp bolt FLAT WASHER, 316 stainless steel, bright finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.95

HCP26189 Aftermarket header pipe outlet-to-collector inlet clamp bolt FLAT WASHER, alloy steel, black finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 2.95



HCP9711 Aftermarket chrome-plated header pipe outlet-to-collector inlet PINCH CLAMP, complete with attaching hardware, use 1 per pipe, for all XJ900RK, RL, N/FN, and F models. NOTE: original clamps are spot-welded onto pipe; spot weld must be broken to remove original clamps! Each:
$ 11.95



HCP3931 OEM collector rear support BOLT, alloy steel, bright finish, use 1 per bike, for all XJ900RK, RL, N/FN, and F models, each:
$ 2.95

HCP26191 Aftermarket collector rear support BOLT, alloy steel, bright finish, use 1 per bike, for all XJ900RK, RL, N/FN, and F models, each:
$ 2.25


HCP2637 OEM collector rear support RUBBER INSULATOR (damper), use 2 per bike, for all XJ900RK, RL, N/FN, and F models, each:
$ 19.95

HCP2632 OEM collector rear SUPPORT BRACKET, use 1 per bike, for all XJ900RK, RL, N/FN, and F models, each:
$ 49.95

HCP2635 OEM collector rear support rubber insulator COLLAR, use 1 per bike, for all XJ900RK, RL, N/FN, and F models, each:
$ 27.95



HCP3925 OEM collector rear support bracket-to-frame mounting BOLT, alloy steel hex-head bolt with a bright finish, use 2 per bike, for all XJ900RK, RL, N/FN, and F models, each:
$ 2.95

HCP17143 Aftermarket collector rear support bracket-to-frame mounting BOLT, steel hex-head bolt with a bright silver-zinc finish, use 2 per bike, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.25

HCP22195 Aftermarket collector rear support bracket-to-frame mounting BOLT, alloy steel hex-head bolt with a bright yellow-zinc finish, use 2 per bike, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.50

HCP17144 Aftermarket collector rear support bracket-to-frame mounting BOLT, alloy steel hex-head bolt with a black finish, use 2 per bike, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.95

HCP17145 Aftermarket collector rear support bracket-to-frame mounting BOLT, 18/8 stainless steel hex-head bolt with a bright finish, use 2 per bike, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.75

HCP22198 Aftermarket collector rear support bracket-to-frame mounting BOLT, 316 stainless steel hex-head bolt with a bright finish, use 2 per bike for all XJ900RK, RL, N/FN, and F models, each:
$ 1.95

HCP22200 Aftermarket collector rear support bracket-to-frame mounting BOLT, high-strength alloy steel socket head (hex-key) bolt with a black finish, use 2 per bike, for all XJ900RK, RL, N/FN, and F models, each:
$ 3.95

HCP22201 Aftermarket collector rear support bracket-to-frame mounting BOLT, alloy steel socket head (hex-key) bolt with a bright finish, use 2 per bike, for all XJ900RK, RL, N/FN, and F models, each:
$ 3.95

HCP22202 Aftermarket collector rear support bracket-to-frame mounting BOLT, 18/8 stainless steel socket head (hex-key) bolt with a bright finish, use 2 per bike, for all XJ900RK, RL, N/FN, and F models, each:
$ 3.95

HCP24125 Aftermarket collector rear support bracket-to-frame mounting BOLT, 316 stainless steel socket head (hex-key) bolt with a bright finish, use 2 per bike, for all XJ900RK, RL, N/FN, and F models, each:
$ 4.95



HCP2537 OEM collector rear support bracket-to-frame mounting bolt FLAT WASHER, alloy steel, bright finish, use 2 per bike, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.95

HCP3945 OEM collector rear support bracket-to-frame mounting bolt FLAT WASHER, alloy steel, black finish, use 2 per bike, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.95

HCP26192 Aftermarket collector rear support bracket-to-frame mounting bolt FLAT WASHER, alloy steel, bright finish, use 2 per bike, for all XJ900RK, RL, N/FN, and F models, each:
$ 0.95

HCP26193 Aftermarket collector rear support bracket-to-frame mounting bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 2 per bike, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.25

HCP17110 Aftermarket collector rear support bracket-to-frame mounting bolt FLAT WASHER, 316 stainless steel, bright finish, use 2 per bike, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.95

HCP26189 Aftermarket collector rear support bracket-to-frame mounting bolt FLAT WASHER, alloy steel, black finish, use 2 per bike, for all XJ900RK, RL, N/FN, and F models, each:
$ 2.95



HCP3925 OEM collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel hex-head bolt with a bright finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 2.95

HCP17143 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, steel hex-head bolt with a bright silver-zinc finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.25

HCP22195 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel hex-head bolt with a bright yellow-zinc finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.50

HCP17144 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel hex-head bolt with a black finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.95

HCP17145 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 18/8 stainless steel hex-head bolt with a bright finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.75

HCP22198 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 316 stainless steel hex-head bolt with a bright finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.95

HCP22200 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, high-strength alloy steel socket head (hex-key) bolt with a black finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 3.95

HCP22201 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel socket head (hex-key) bolt with a bright finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 3.95

HCP22202 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 18/8 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 3.95

HCP24125 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 316 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 4.95



HCP2537 OEM collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.95

HCP26192 Aftermarket collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 0.95

HCP26193 Aftermarket collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.25

HCP17110 Aftermarket collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, 316 stainless steel, bright finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.95

HCP26189 Aftermarket collector outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, alloy steel, black finish, use 1 per muffler, for all XJ900RK, RL, N/FN, and F models, each:
$ 2.95



HCP9713 Aftermarket chrome-plated header pipe outlet-to-collector inlet PINCH CLAMP, complete with attaching hardware, use 1 per pipe, for all XJ900RK, RL, N/FN, and F models. NOTE: original clamps are spot-welded onto pipe; spot weld must be broken to remove original clamps! Each:
$ 11.95



HCP3929 OEM muffler-to-rear footpeg bracket mounting BOLT, alloy steel, socket head cap screw with a bright finish, use 1 per side, for all XJ900RK, RL, N/FN, and F models, each :
$ 2.95

HCP22206 Aftermarket muffler-to-rear footpeg bracket mounting BOLT, alloy steel, socket head cap screw with a black finish, use 1 per side, for all XJ900RK, RL, N/FN, and F models, each:
$ 1.95

HCP3942 OEM muffler mounting bolt OVAL NUT, use 1 per side, for all XJ900RK, RL, N/FN, and F models, each:
$ 19.95

HCP26217 Aftermarket muffler mounting bracket bolt OVAL NUT, use 1 per side, for all XJ900RK, RL, N/FN, and F models, each:
$ 11.95



HCP2639 OEM left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used, for all XJ900RK, RL, N/FN, and F models, each:
$ 12.95

HCP2640 OEM left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used. NOTE: this bumper is approximately 3mm shorter than the original HCP2639 bumper, but will still fit and function properly (and is about 1/2 the price of the correct bumper). Fits all XJ900RK, RL, N/FN, and F models, each:
$ 7.95

HCP26234 Aftermarket left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used. NOTE: this bumper is approximately 3mm shorter than the original HCP2639 bumper, but will still fit and function properly (and is about 1/2 the price of the correct bumper). Fits all XJ900RK, RL, N/FN, and F models, each:
$ 5.95



HCP15660 Aftermarket frame tube NOISE EMISSIONS CERTIFICATION DECAL, white decal with black wording provides model-specific information stating that the bike conforms to federal nose level standards. Used on all XJ900RK models on the right frame downtube, just below the steering headpipe tube.
$ 10.95



XJ1100 and XS1100 models:

HCP2942 OEM cylinder head exhaust port THREADED STUD, dark finish, alloy steel. Use 2 per header pipe, for all XJ1100 and XS1100 models, each:
$ 5.95
$ 44.95 per set of 8

HCP25811 Aftermarket cylinder head exhaust port THREADED STUD, dark finish, alloy steel. Use 2 per header pipe, for all XJ1100 and XS1100 models, each:
$ 3.95
$ 29.95 per set of 8

HCP25812 Aftermarket cylinder head exhaust port THREADED STUD, bright finish, 18-8 stainless steel. Use 2 per header pipe, for all XJ1100 and XS1100 models, each:
$ 4.95
$ 37.95 per set of 8



HCP2617 OEM header pipe to above stud CHROME BARREL NUT, use 2 per header pipe, for all XJ1100 models, each:
$ 5.95
$ 46.95 per set of 8

HCP3943 OEM header pipe to above stud CHROME BARREL NUT, use 2 per header pipe, for all XS1100 models except 1980-81 Midnight Special models (these will fit the Midnight models, but not the correct finish), each:
$ 5.95
$ 46.95 per set of 8



HCP2615 OEM header pipe large finned, cast aluminum RING NUT, use 1 per pipe, for all XJ1100 and XS1100 Standard and Special models, each:
$ discontinued



HCP2182 OEM header pipe gas analysis test port BOLT, 6-point hex head alloy steel fastener with a bright finish, use 1 per pipe, for all XJ1100 models, each:
$ 2.95

HCP22180 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head alloy steel fastener with a dark finish, use 1 per pipe, for all XJ1100 models, each:
$ 1.25

HCP22182 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head 18/8 stainless steel fastener with a bright finish, use 1 per pipe, for all XJ1100 models, each:
$ 1.75

HCP22183 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head 316 stainless steel fastener with a bright finish, use 1 per pipe, for all XJ1100 models, each:
$ 1.95

HCP22181 A Aftermarket header pipe gas analysis test port BOLT, 6-point hex head alloy steel fastener has a serrated flange (which eliminates the need for using a lockwasher) and features a dark finish, use 1 per pipe, for all XJ1100 models, each:
$ 1.95



HCP3933 OEM header pipe gas analysis test port BOLT, 6-point hex head alloy steel fastener with a dark finish, use 1 per pipe, for 1981 XS1100 Midnight Special models, each:
$ 2.95

HCP22180 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head alloy steel fastener with a dark finish, use 1 per pipe, for 1981 XS1100 Midnight Special models, each:
$ 1.25

HCP22182 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head 18/8 stainless steel fastener with a bright finish, use 1 per pipe, for 1981 XS1100 Midnight Special models, each:
$ 1.75

HCP22183 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head 316 stainless steel fastener with a bright finish, use 1 per pipe, for 1981 XS1100 Midnight Special models, each:
$ 1.95

HCP22181 Aftermarket header pipe gas analysis test port BOLT, 6-point hex head alloy steel fastener has a serrated flange (which eliminates the need for using a lockwasher) and features a dark finish, use 1 per pipe, for 1981 XS1100 Midnight Special models, each:
$ 1.95



HCP2173 OEM header pipe gas analysis test port bolt FLAT WASHER, original bright finish, use 1 per pipe, for all XJ1100 and 1981 XS1100 Standard and Special models, each:
$ 1.95

HCP1869 OEM header pipe gas analysis test port bolt FLAT WASHER, black-oxide finish, use 1 per pipe, for 1981 XS1100 Midnight Special models, each:
$ 1.95

HCP6642 Aftermarket header pipe gas analysis test port bolt FLAT WASHER, zinc-plated alloy steel with a bright finish, use 1 per pipe on all XJ1100 and 1981 XS1100 models, each:
$ 0.95

HCP6643 Aftermarket header pipe gas analysis test port bolt FLAT WASHER, 18-8 stainless steel, use 1 per pipe on all XJ1100 and 1981 XS1100 models, each:
$ 1.25

HCP25756 Aftermarket header pipe gas analysis test port bolt FLAT WASHER, 316 stainless steel, use 1 per pipe on all XJ1100 and 1981 XS1100 models, each:
$ 1.95

HCP14285 Aftermarket header pipe gas analysis test port bolt FLAT WASHER, black oxide-coated 18-8 stainless steel, use 1 per pipe on all XJ1100 and 1981 XS1100 models, each:
$ 1.95



HCP3940 OEM #2 header pipe outlet-to-collector inlet PINCH CLAMP, use 1, for all XJ1100 and XS1100 models, each:
$ discontinued

HCP3941 OEM #3 header pipe outlet-to-collector inlet PINCH CLAMP, use 1, for all XJ1100 and XS1100 models, each:
$ discontinued

HCP9713 Aftermarket chrome-plated header pipe outlet-to-collector inlet PINCH CLAMP, complete with attaching hardware, use 1 per pipe, for all XJ1100 and XS1100 models. NOTE: original clamps are spot-welded onto pipe; spot weld must be broken to remove original clamps! Each:
$ 11.95



HCP3925 OEM #2 and #3 header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel hex-head bolt with a bright finish, use 1, for all XJ1100 and XS1100 models, each:
$ 2.95

HCP17143 Aftermarket #2 and #3 header pipe outlet-to-collector inlet pinch clamp BOLT, steel hex-head bolt with a bright silver-zinc finish, use 1, for all XJ1100 and XS1100 models, each:
$ 1.25

HCP22195 Aftermarket #2 and #3 header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel hex-head bolt with a bright yellow-zinc finish, use 1, for all XJ1100 and XS1100 models, each:
$ 1.50

HCP17144 Aftermarket #2 and #3 header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel hex-head bolt with a black finish, use 1, for all XJ1100 and XS1100 models, each:
$ 1.95

HCP17145 Aftermarket #2 and #3 header pipe outlet-to-collector inlet pinch clamp BOLT, 18/8 stainless steel hex-head bolt with a bright finish, use 1, for all XJ1100 and XS1100 models, each:
$ 1.75

HCP22198 Aftermarket #2 and #3 header pipe outlet-to-collector inlet pinch clamp BOLT, 316 stainless steel hex-head bolt with a bright finish, use 1, for all XJ1100 and XS1100 models, each:
$ 1.95

HCP22200 Aftermarket #2 and #3 header pipe outlet-to-collector inlet pinch clamp BOLT, high-strength alloy steel socket head (hex-key) bolt with a black finish, use 1, for all XJ1100 and XS1100 models, each:
$ 3.95

HCP22201 Aftermarket #2 and #3 header pipe outlet-to-collector inlet pinch clamp BOLT, alloy steel socket head (hex-key) bolt with a bright finish, use 1, for all XJ1100 and XS1100 models, each:
$ 3.95

HCP22202 Aftermarket #2 and #3 header pipe outlet-to-collector inlet pinch clamp BOLT, 18/8 stainless steel socket head (hex-key) bolt with a bright finish, use 1, for all XJ1100 and XS1100 models, each:
$ 3.95

HCP24125 Aftermarket #2 and #3 header pipe outlet-to-collector inlet pinch clamp BOLT, 316 stainless steel socket head (hex-key) bolt with a bright finish, use 1, for all XJ1100 and XS1100 models, each:
$ 4.95



HCP2537 OEM #2 and #3 header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per pipe, for all XJ1100 and XS1100 models, each:
$ 1.95

HCP26192 Aftermarket #2 and #3 header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per pipe, for all XJ1100 and XS1100 models, each:
$ 0.95

HCP26193 Aftermarket #2 and #3 header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 1 per pipe, for all XJ1100 and XS1100 models, each:
$ 1.25

HCP17110 Aftermarket #2 and #3 header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, 316 stainless steel, bright finish, use 1 per pipe, for all XJ1100 and XS1100 models, each:
$ 1.95

HCP26189 Aftermarket #2 and #3 header pipe outlet-to-collector inlet pinch clamp bolt FLAT WASHER, alloy steel, black finish, use 1 per pipe, for all XJ1100 and XS1100 models, each:
$ 2.95



HCP3940 OEM left collector pipe outlet-to-muffler inlet PINCH CLAMP, use 1, for all XJ1100 and XS1100 models, each:
$ discontinued

HCP3941 OEM right collector pipe outlet-to-muffler inlet PINCH CLAMP, use 1, for all XJ1100 and XS1100 models, each:
$ discontinued

HCP9713 Aftermarket chrome-plated left or right collector pipe outlet-to-muffler inlet PINCH CLAMP, complete with attaching hardware, use 1 per pipe, for all XJ1100 and XS1100 models. NOTE: original clamps are spot-welded onto pipe; spot weld must be broken to remove original clamps! Each:
$ 11.95



HCP3925 OEM collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel hex-head bolt with a bright finish, use 1 per muffler, for all XJ1100 and XS1100 models, each:
$ 2.95

HCP17143 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, steel hex-head bolt with a bright silver-zinc finish, use 1 per muffler, for all XJ1100 and XS1100 models, each:
$ 1.25

HCP22195 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel hex-head bolt with a bright yellow-zinc finish, use 1 per muffler, for all XJ1100 and XS1100 models, each:
$ 1.50

HCP17144 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel hex-head bolt with a black finish, use 1 per muffler, for all XJ1100 and XS1100 models, each:
$ 1.95

HCP17145 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 18/8 stainless steel hex-head bolt with a bright finish, use 1 per muffler, for all XJ1100 and XS1100 models, each:
$ 1.75

HCP22198 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 316 stainless steel hex-head bolt with a bright finish, use 1 per muffler, for all XJ1100 and XS1100 models, each:
$ 1.95

HCP22200 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, high-strength alloy steel socket head (hex-key) bolt with a black finish, use 1 per muffler, for all XJ1100 and XS1100 models, each:
$ 3.95

HCP22201 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, alloy steel socket head (hex-key) bolt with a bright finish, use 1 per muffler, for all XJ1100 and XS1100 models, each:
$ 3.95

HCP22202 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 18/8 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per muffler, for all XJ1100 and XS1100 models, each:
$ 3.95

HCP24125 Aftermarket collector outlet-to-muffler inlet pinch clamp BOLT, 316 stainless steel socket head (hex-key) bolt with a bright finish, use 1 per muffler, for all XJ1100 and XS1100 models, each:
$ 4.95



HCP2537 OEM collector pipe outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per pipe, for all XJ1100 and XS1100 models, each:
$ 1.95

HCP26192 Aftermarket collector pipe outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1 per pipe, for all XJ1100 and XS1100 models, each:
$ 0.95

HCP26193 Aftermarket collector pipe outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 1 per pipe, for all XJ1100 and XS1100 models, each:
$ 1.25

HCP17110 Aftermarket collector pipe outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, 316 stainless steel, bright finish, use 1 per pipe, for all XJ1100 and XS1100 models, each:
$ 1.95

HCP26189 Aftermarket collector pipe outlet-to-muffler inlet pinch clamp bolt FLAT WASHER, alloy steel, black finish, use 1 per pipe, for all XJ1100 and XS1100 models, each:
$ 2.95



HCP3940 OEM left-to-right crossover pipe PINCH CLAMP, use 1, for all XJ1100 and XS1100 models, each:
$ discontinued

HCP9713 Aftermarket chrome-plated collector-outlet-to-muffler inlet PINCH CLAMP, complete with attaching hardware, use 1 per pipe, for all XJ1100 and XS1100 models. NOTE: original clamps are spot-welded onto pipe; spot weld must be broken to remove original clamps! Each:
$ 11.95


HCP3925 OEM left-to-right crossover pipe pinch clamp BOLT, alloy steel hex-head bolt with a bright finish, use 1, for all XJ1100 and XS1100 models, each:
$ 2.95

HCP17143 Aftermarket left-to-right crossover pipe pinch clamp BOLT, steel hex-head bolt with a bright silver-zinc finish, use 1, for all XJ1100 and XS1100 models, each:
$ 1.25

HCP22195 Aftermarket left-to-right crossover pipe pinch clamp BOLT, alloy steel hex-head bolt with a bright yellow-zinc finish, use 1, for all XJ1100 and XS1100 models, each:
$ 1.50

HCP17144 Aftermarket left-to-right crossover pipe pinch clamp BOLT, alloy steel hex-head bolt with a black finish, use 1, for all XJ1100 and XS1100 models, each:
$ 1.95

HCP17145 Aftermarket left-to-right crossover pipe pinch clamp BOLT, 18/8 stainless steel hex-head bolt with a bright finish, use 1, for all XJ1100 and XS1100 models, each:
$ 1.75

HCP22198 Aftermarket left-to-right crossover pipe pinch clamp BOLT, 316 stainless steel hex-head bolt with a bright finish, use 1, for all XJ1100 and XS1100 models, each:
$ 1.95

HCP22200 Aftermarket left-to-right crossover pipe pinch clamp BOLT, high-strength alloy steel socket head (hex-key) bolt with a black finish, use 1, for all XJ1100 and XS1100 models, each:
$ 3.95

HCP22201 Aftermarket left-to-right crossover pipe pinch clamp BOLT, alloy steel socket head (hex-key) bolt with a bright finish, use 1, for all XJ1100 and XS1100 models, each:
$ 3.95

HCP22202 Aftermarket left-to-right crossover pipe pinch clamp BOLT, 18/8 stainless steel socket head (hex-key) bolt with a bright finish, use 1, for all XJ1100 and XS1100 models, each:
$ 3.95

HCP24125 Aftermarket left-to-right crossover pipe pinch clamp BOLT, 316 stainless steel socket head (hex-key) bolt with a bright finish, use 1, for all XJ1100 and XS1100 models, each:
$ 4.95



HCP2537 OEM left-to-right crossover pipe pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1, for all XJ1100 and XS1100 models, each:
$ 1.95

HCP26192 Aftermarket left-to-right crossover pipe pinch clamp bolt FLAT WASHER, alloy steel, bright finish, use 1, for all XJ1100 and XS1100 models, each:
$ 0.95

HCP26193 Aftermarket left-to-right crossover pipe pinch clamp bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 1, for all XJ1100 and XS1100 models, each:
$ 1.25

HCP17110 Aftermarket left-to-right crossover pipe pinch clamp bolt FLAT WASHER, 316 stainless steel, bright finish, use 1, for all XJ1100 and XS1100 models, each:
$ 1.95

HCP26189 Aftermarket left-to-right crossover pipe pinch clamp bolt FLAT WASHER, alloy steel, black finish, use 1, for all XJ1100 and XS1100 models, each:
$ 2.95



HCP3572 OEM #1 and #4 collector pipe chrome cover BOLT, black finish, 6-point hex-head style, use 2 per side, for all XJ1100 models, each:
$ 2.95

HCP22159 Aftermarket #1 and #4 collector pipe chrome cover BOLT, zinc-plated alloy steel, 6-point hex-head style, use 2 per side, for all XJ1100 models, each:
$ 1.00

HCP22160 Aftermarket #1 and #4 collector pipe chrome cover BOLT, 18/8 stainless steel, 6-point hex-head style, use 2 per side, for all XJ1100 models, each:
$ 1.95

HCP21964 Aftermarket #1 and #4 collector pipe chrome cover BOLT, black-oxide coated alloy steel, socket head (hex-key) style fastener, use 2 per side, for all XJ1100 models, each:
$ 1.95


HCP10826 OEM #1 and #4 collector pipe chrome cover bolt FLAT WASHER, use 2 per side, for all XJ1100 models, each:
$ 2.95



HCP24633 Aftermarket muffler mounting RUBBER DAMPER, helps prevents vibration and a “squeaky” exhaust system. Use 1 per side, this round hard rubber grommet presses into the rear footrest bracket. For all XJ650 Maxim and Midnight Maxim, XJ1100, all 1979-81 XS1100 Special and Midnight Special, and all 1981 XS1100 Standard models,. Each:
$ 21.95


HCP22819 OEM muffler mounting RUBBER DAMPER, helps prevents vibration and a “squeaky” exhaust system. Use 1 per side, this round hard rubber bushing presses into the rear footrest bracket. For all 1984-85 FJ600, 1992-98 XJ600 Seca II, 1982 XJ750 Maxim, and all 1978-80 XS1100 Standard models. Each:
$ 7.95

HCP22820 OEM muffler mounting bolt rubber damper metal SLEEVE. Use 1 per footrest. For all 1984-85 FJ600, 1992-98 XJ600 Seca II, 1982 XJ750 Maxim and 1978-80 XS1100 Standard models. Each:
$ 8.95


HCP3931 OEM muffler mounting FLANGE BOLT, alloy steel, bright finish, use 1 per side, for all XJ1100 and all 1980-81 XS1100 (except 1980 XS1100 Standard) models, each:
$ 2.95

HCP26191 Aftermarket muffler mounting FLANGE BOLT, alloy steel, bright finish, use 1 per side, for all XJ1100 and all 1980-81 XS1100 (except 1980 XS1100 Standard) models, each:
$ 2.25


HCP21872 OEM muffler mounting FLANGE BOLT, use 1 per side, for all 1978-79 XS1100 and 1980 XS1100 Standard models, each:
$ 2.95


HCP4208 OEM muffler hanger bracket-to-muffler mounting BOLT, alloy steel with a dark finish, hex-head bolt, use 2 per side, for all 1978-79 XS1100 and 1980 XS1100 Standard models, each:
$ 2.95

HCP6156 OEM muffler hanger bracket-to-muffler mounting BOLT, hex-head alloy steel with a bright finish, use 2 per side, for all 1978-79 XS1100 and 1980 XS1100 Standard models. Bright-plated (unlike original bolt, which was black-coated); integral lockwasher is not included and should be ordered separately from choices listed further below. Each:
$ 2.95

HCP18159 Aftermarket muffler hanger bracket-to-muffler mounting BOLT, hex-head 18/8 stainless steel with a bright finish, use 2 per side, for all 1978-79 XS1100 and 1980 XS1100 Standard models). Lockwasher is not included and should be ordered separately from choices listed further below. Each:
$ 2.50

HCP16101 Aftermarket muffler hanger bracket-to-muffler mounting BOLT, hex-head alloy steel with a black finish, use 2 per side, for all 1978-79 XS1100 and 1980 XS1100 Standard models. Lockwasher is not included and should be ordered separately from choices listed further below. Each:
$ 2.50




HCP2185 OEM muffler mounting bolt LOCK WASHER, use 2 per side, for all 1978-79 XS1100 and 1980 XS1100 Standard models, each:
$ 1.95

HCP16209 Aftermarket zinc-plated alloy steel muffler mounting bolt LOCK WASHER, use 2 per side, for all 1978-79 XS1100 and 1980 XS1100 Standard models, each:
$ 0.95

HCP16100 Aftermarket 18-8 stainless-steel with a bright finish, muffler mounting bolt LOCK WASHER, use 2 per side, for all 1978-79 XS1100 and 1980 XS1100 Standard models, each:
$ 0.95

HCP16102 Aftermarket black-oxide coated finish muffler mounting bolt LOCK WASHER, use 2 per side, for all 1978-79 XS1100 and 1980 XS1100 Standard models, each:
$ 0.95


HCP2230 OEM muffler mounting bolt FLAT WASHER, use 1 per side, for all 1978-79 XS1100 and 1980 XS1100 Standard models, each:
$ 2.75

HCP22225 Aftermarket muffler mounting bolt FLAT WASHER, zinc-plated alloy steel. Use 1 per side, for all 1978-79 XS1100 and 1980 XS1100 Standard models, each:
$ 1.50

HCP22227 Aftermarket muffler mounting bolt FLAT WASHER, 18/8 stainless steel. Use 1 per side, for all 1978-79 XS1100 and 1980 XS1100 Standard models, each:
$ 1.95


HCP3946 OEM muffler mounting bolt FLAT WASHER, alloy steel, bright finish, use 1 per side, for all XJ1100 and all 1980-81 XS1100 (except 1980 XS1100 Standard) models, each:
$ 3.95

HCP26196 Aftermarket muffler mounting bolt FLAT WASHER, alloy steel, bright finish, use 1 per side, for all XJ1100 and all 1980-81 XS1100 (except 1980 XS1100 Standard) models, each:
$ 1.95

HCP26197 Aftermarket muffler mounting bolt FLAT WASHER, 18/8 stainless steel, bright finish, use 1 per side, for all XJ1100 and all 1980-81 XS1100 (except 1980 XS1100 Standard) models, each:
$ 2.95

HCP26198 Aftermarket muffler mounting bolt FLAT WASHER, 316 stainless steel, dull finish, use 1 per side, for all XJ1100 and all 1980-81 XS1100 (except 1980 XS1100 Standard) models, each:
$ 3.95


HCP3942 OEM muffler mounting bolt OVAL NUT, use 1 per side, for all XJ1100 and all 1980-81 XS1100 (except 1980 XS1100 Standard) models, each:
$ 19.95

HCP26217 Aftermarket muffler mounting bracket bolt OVAL NUT, use 1 per side, for all XJ1100 and all 1980-81 XS1100 (except 1980 XS1100 Standard) models, each:
$ 11.95



HCP2250 OEM muffler mounting bolt chrome-plated domed CROWN NUT, use 1 per side, for all 1978-79 XS1100 and 1980 XS1100 Standard models, each:
$ 6.95

HCP16424 Aftermarket muffler mounting bolt chrome-plated domed CROWN NUT, use 1 per side, for all 1978-79 XS1100 and 1980 XS1100 Standard models. This nut is a bit taller compared to the original HCP2250 nut, and has a beautiful, highly polished chrome finish compared to the stock OEM nut, and the extra height is visually pleasing. Each:
$ 6.95



HCP2639 OEM left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used, for all XJ1100 models and all 1980-81 XS1100 (except 1980 XS1100 Standard) models, each:
$ 12.95

HCP2640 OEM left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used. NOTE: this bumper is approximately 3mm shorter than the original HCP2639 bumper, but will still fit and function properly (and is about 1/2 the price of the correct bumper). Fits all XJ1100 models and all 1980-81 XS1100 (except 1980 XS1100 Standard) models, each:
$ 7.95

HCP26234 Aftermarket left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used. NOTE: this bumper is approximately 3mm shorter than the original HCP2639 bumper, but will still fit and function properly (and is about 1/2 the price of the correct bumper). Fits all XJ1100 models and all 1980-81 XS1100 (except 1980 XS1100 Standard) models, each:
$ 5.95



HCP2640 OEM left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used, for all 1978 XS1100 Standard models, each:
$ 7.95

HCP26234 Aftermarket left side muffler rubber BUMPER, for where the centerstand contacts the left muffler when not being used, for all 1978 XS1100 Standard models, each:
$ 5.95

Return to Top of Page