| XJ4Ever.com PO Box 98393 Atlanta, GA 30359-8393 Info@xj4ever.com
|
 |
GASKET SUPPLIES AND TOOLS:
Gasket Adhesives and Removers:
b4) Aftermarket pure SILICONE GREASE----this is the proper product to use when installing any rubber-based o-ring or seal or paper gasket. Silicone doesn't affect rubber, provides good seal lubrication, can also be used as a "glue" to hold gaskets and seals in place during installation, and to aid in the re-assembly of components.
HCP28407 Aftermarket o-ring, oil seal, and gasket installation pure SILICONE GREASE. This small 5-gram (1/6-oz) snap-open "pillow packet" is enough for a few small oil seals, dozens of o-rings, and the like. Each:
$ 4.95
HCP1714 Aftermarket o-ring, oil seal, and gasket installation pure SILICONE GREASE. This generous 14-gram (1/2-oz.) tub goes a long way, because just like Brylcreem, "just a little dab will do ya'!" Each:
$ 9.95
HCP3120 Aftermarket black GASKET MAKER, large family-sized 3.8 ounce squeeze tube. Enough to do about five thousand cam end plugs! I'm sure it works well in other applications. This is for use on the half-moon end plugs (HCP1619 for non-YICS applications) and the molded-in end plugs (part of the actual rubber gasket) on YICS engines. Do not use on the paper or rubber valvecover gasket itself! Each:
$ 11.95
HCP3120A Aftermarket black GASKET MAKER, smaller 1/2-ounce squeeze tube. Enough to do a few hundred cam end plugs! It's the smallest size offered. I'm sure it works well in other applications. This is for use on the half-moon end plugs (HCP1619 for non-YICS applications) and the molded-in end plugs (part of the actual rubber gasket) on YICS engines. Do not use on the paper or rubber valvecover gasket itself! Each:
$ 7.95
HCP25092 Aftermarket high-performance aviation-grade, black, non-hardening GASKET MAKER, 1.5 ounce squeeze tube. This special high-performance sealant is ideal for use on engine case covers as a “problem solver” material which will compensate for poor machining tolerances or the slight warpage that can occur over time on precision-fit pieces. A very thin film of this material is all that is needed! Each:
$ 8.95
NOTE: the following product(s) can only be shipped via ground transport (which thus eliminates the postal Priority Mail, postal Express Mail, or private carrier Expedited levels of service for this item) and cannot (and will not----don't even ask!) be shipped outside of the continental USA. Additionally, there may be a per-package weight or quantity restriction, and thus multiple-unit orders of this product may have to be shipped in separate packages and will incur additional shipping charges.
HCP20861 Aftermarket industrial-strength SILICONE LUBE, in a large 16-ounce aerosol can. Concentrated silicone sprays on wet, and then dries to a super-slick, clear, non-greasy, non-staining finish. Resists moisture, stops squeeks, prevents binding on all types of surfaces (wood, metal, plastic, rubber, even fabrics). Won't wash away, protect against rust and corrosion, stable from -100 degrees up to 500-F. This fluid is also a great choice for use as installation lubricant for o-rings, oil seals, etc. (similar to our HCP1714 or HCP28407 silicone grease paste) or wherever petroleum-based lubricants are not recommended.
$ 24.95
HCP9611 Aftermarket engine STANDARD GASKET REMOVER. This highly effective formula makes softens and dissolves gasket materials and adhesives, making for easy and quick gasket removal. Especially useful on cylinder base gaskets and side cover gaskets. NOTE: this formula will remove the clear-coat finish found on many engine parts! 12-ounce spray can. Each:
$ discontinued
HCP10492 Aftermarket cylinder head gasket high-performance GASKET SEAL SPRAY. This high copper content, high-temperature aerosol spray helps position and seal gaskets in place. Use to seal cylinder head gaskets, cylinder base gaskets, and even side cover gaskets in position (note: when using on side cover gaskets, apply thin film of spray to the engine-case side of the gasket only, and use 100% silicone lube on the cover side of the gasket. This method will allow you to easily remove the cover in the future, without tearing the gasket). Note that this is not the material to use with valvecover gaskets; for those, use the HCP3120 or HCP25092 material for flat paper gaskets, or HCP17198 for the molded rubber valvecover gaskets. Each:
$ 11.95
HCP17198 Aftermarket valvecover gasket HI-TACK ADHESIVE. This fast-drying, high-temperature adhesive helps position and seal the molded rubber valvecover gaskets in place. Comes in a 4-ounce brush-top can Each:
$ 9.95
HCP10491 Aftermarket engine case GASKET MAKER. This high-temperature, solvent-based bonding caulk forms a tough, flexible seal on irregular or uneven surfaces, is fuel and oil resistant, and is rated for 350-F degrees. Use to seal the upper and lower crankcase halves together. 2.7 ounce squeeze tube, enough to do one engine (you apply a thin coat, not a big dripping glob!). NOTE: you should review a service manual before applying this material to the engine cases, as there are certain areas (particularly around oil feed holes) that should never have sealer applied near them. See the bottom of page 2:
http://www.xjbikes.com/forums/threads/transmission-issue.59920/page-2#post-462239
NOTE: the easiest way to use this product is to squirt a small amount into the bottom corner of a standard baggie, and the snip that bottom corner a tiny bit; in this manner, you can then squeeze a small and precise bead right where you want it. Each:
$ 9.95
Gasket Scrapers:
HCP15410 Aftermarket 3/8" square GASKET SCRAPER, 3" long bar of square tool steel cutting block works as an exceptional gasket removal device when it's held flat and worked back-and-forth against a surface such as a cylinder head, the jugs, crankcase cover opening flanges, etc. Simple, easy to use, long-lasting. Will not work on any surface that requires gasket removal in a "recessed" area. Removes old engine case cover or cylinder head gasket remnants effortlessly.
$ 7.95
HCP15434 Aftermarket 3/8" square GASKET SCRAPER, 3" long bar of square cobalt-impregnated, tool steel cutting block works as an exceptional gasket removal device when it's held flat and worked back-and-forth against a surface such as a cylinder head, the jugs, crankcase cover opening flanges, etc. Simple, easy to use, will last a lifetime. Will not work on any surface that requires gasket removal in a "recessed" area. Removes old engine case cover or cylinder head gasket remnants effortlessly.
$ 9.95
HCP6377 Aftermarket long-handled GASKET SCRAPER, forged steel with 1" wide blade (can be re-sharpened), 10-1/2" long, comfort-grip handle. Removes old engine case cover or cylinder head gasket remnants effortlessly.
$ 14.95
HCP6376 Aftermarket set of long-handled GASKET SCRAPER SET, all are made from a black-coated, heat-treated forged alloy steel with a variety of blade sizes and style (blades can be re-sharpened) to cover all situations. Each set has one each of the HCP6377 10-1/2" long tool, an 8" long offset blade scraper, a 7" long x 5/8" wide blade scraper, and a stubby flat-blade scraper tool.
$ 69.95
HCP13101 Aftermarket long-handled BLADE-STYLE GASKET SCRAPER, uses replaceable 1-1/2" wide single-edge disposable blades. 11-1/2" long, comfort-grip handle is also used to store extra blades. Comes with 5 carbon-steel blades and one plastic scraper blade. Order replacement blades HCP13103 below. Great for removing really stuck cylinder head and case gaskets or adhesive precisely and safely.
$ 19.95
HCP13103 Aftermarket replacement set of SCRAPER BLADES, set of 5 stainless-steel 1-1/2" wide blades for the HCP13101 scraper tool above.
$ 2.95
HCP13102 Aftermarket short-handled BLADE-STYLE GASKET SCRAPER, comes with 6 replaceable, 1-7/8" wide carbon-steel single-edge disposable blades. 6" long, comfort-grip handle is also used to store extra blades. Order replacement blades HCP13104 below. Great for removing really stuck cylinder head and case gaskets or adhesive precisely and safely.
$ 9.95
HCP13104 Aftermarket replacement set of SCRAPER BLADES, set of 5 carbon-steel 1-7/8" wide blades for the HCP13102 scraper tool above.
$ 4.95
Oil Seal and O-ring Tools:
u) Aftermarket o-ring and seal PICK TOOL SET. A very handy set of 4 different style o-ring removal - dental-picks, in a variety of pick angles and styles, all in a handy plastic storage pouch. The HCP1411 picks are a high-quality, professional use style that feature individual pick shafts that interchange into a 5" long, knurled, easy-grip handle, and are small enough to fit easily into the tiny idle mixture screw bores and other such passages. The HCP9974 style feature four different individual picks, each secured into their own impact-resistant, sure-grip plastic handle.
HCP1411 Aftermarket set of four different o-ring and seal PICKS, metal handles.
$ 24.95
HCP9974 Aftermarket set of four different o-ring and seal PICKS, plastic handles, good inexpensive set.
$ 19.95
js44) Aftermarket dual-tip SEAL PULLER. Our large HCP9801 style puller features curved dual tips on a rounded head allows you to "lever out" large, thick rubber seals safely and properly, while the smaller HCP9961 puller works better with smaller seals (such as on your shifter side cover). These tools are a much better solution than trying to use a screwdriver to pry out seals as they eliminate the risk of scratching or damaging the seal land.
NOTE: in some situations, you can use the following technique to remove larger oil seals that would otherwise require case-splitting to remove. All large oil seals have a metal inner structure that you can (very carefully!) drill into and then pry out:
http://www.xjbikes.com/forums/threads/replacing-the-output-shaft-seal.110522/
HCP9801 Aftermarket rubber LARGE SEAL PULLER TOOL.
$ 16.95
HCP9961 Aftermarket rubber SMALL SEAL PULLER TOOL.
$ 12.95
Anti-Seize Paste:
xx1) Fastener ANTI-SEIZE PASTE. Yeah, it's smelly and makes a silvery mess on your fingers, but this stuff is a life-saver for any true wrencher, because it prevents problems down the road. Use it on any metal fastener that does not require a "loctite" thread-locker material to be used. This means on just about every fastener that is carb, engine case, or suspension-related! (except for carb upper and lower rack-mount screws and butterfly valve screws, which do require the use of a thread-lock fluid). If you think that it might, sometime, in the future, need to come off: use anti-seize compound! NOTE: the "base" metal material used in the different anti-seize pastes below do not determine what type of fastener to use such pastes on; it merely signifies what base material is used to create the anti-seize paste. You can use any "based" anti-seize paste on any type of fastener and metal.
NOTE: the use of anti-seize compounds will result in a TORQUE-MULTIPLYING EFFECT……..the result of a reduction in fricition between the threaded contact points……and thus fasteners treated with anti-seize compound should have their torque values reduced by at least 10-15% when installed into steel material, and up to 25% into aluminum materials or other “soft” metals” (such as spark plugs into cylinder heads, or almost any other type of fastener into the engine) …… note that this rule applies only to service manual torque specifications on fasteners that are not indicated to be treated with anti-seize fluid by the factory …. if the factory manual specifies the use of an anti-seize coating, then the specified torque value for that fitting already takes into account the “reduced torque” necessary.
http://raskcycle.com/techtip/webdoc14.html
http://www.cncexpo.com/MetricBoltTorqueNm.aspx
http://www.bmwmotorcycletech.info/sparkplugs.htm
http://www.antiseize.com/pdf/torque_specifications.pdf
.
HCP1264 Aftermarket fastener ANTI-SEIZE PASTE, standard grade aluminum-based in a 1-ounce squeeze tube, for smaller jobs.
$ 5.95
HCP1265 Aftermarket fastener ANTI-SEIZE PASTE, standard grade aluminum-based formula in a 4-ounce tub with a brush-lid, for larger jobs.
$ 7.95
HCP9784 Aftermarket fastener ANTI-SEIZE PASTE, standard grade aluminum-based formula in an 8-ounce tub with a brush-lid, a lifetime supply for your motorcycle!
$ 12.95
HCP9763 Aftermarket fastener ANTI-SEIZE PASTE, standard-grade copper-based formula in an 8-ounce tub with a brush-lid, a lifetime supply for your motorcycle!
$ 12.95
HCP9764 Aftermarket fastener ANTI-SEIZE PASTE, premium-grade nickel-based formula in an 8-ounce tub with a brush-lid, a lifetime supply for your motorcycle!
$ 17.95
Thread-Locker Fluids:
xx2) The next most important tool: fastener THREAD LOCKER FLUIDS. Use on any fastener that you don't normally ever remove, to make sure that it stays that way. Comes in a variety of formulas, each one designed for a specific use as explained below.
HCP1266 Low Strength THREAD LOCKER FLUID, 6ml squeeze tube. This is a semi-permanent formula that provides moderate vibration-loosening resistance, while still allowing for easy disassembly of the fastener with hand tools. This formula is recommended for upper and lower carb rack mount screws and the butterfly valve-to-throttle shaft retaining screws. A little bit goes a long way.......
$ 11.95
HCP1267 Semi-Permanent THREAD LOCKER FLUID, 6ml squeeze tube. This is semi-permanent formula that provides good vibration-loosening resistance, while still allowing for easy disassembly of the fastener with hand tools. This formula is recommended for use with 6-20mm fasteners.
$ 11.95
HCP27756 Semi-Permanent THREAD LOCKER FLUID, 0.5ml squeeze tube. This is semi-permanent formula that provides good vibration-loosening resistance, while still allowing for easy disassembly of the fastener with hand tools. This formula is recommended for use with 6-20mm fasteners. Small single-use tube is great for, well, small jobs!
$ 3.95
HCP1268 Permanent THREAD LOCKER FLUID, 6ml squeeze tube. This is a high-strength formula that provides superior vibration-loosening resistance, and requires the use of heat or special tools to break loose the fastener for disassembly.
$ 11.95
HCP1269 Permanent THREAD LOCKER FLUID, 6ml squeeze tube. This is both a high-strength AND high-heat formula that provides superior vibration-loosening resistance, and requires the use of heat or special tools to break loose the fastener for disassembly.
$ 11.95
Super-Penetrant Fluids and Lubricants:
Sometimes, the toughest part of working on a vehicle is battling the effects of time: seized fasteners, caused by rust, corrosion, and other factors, turns what should be a 5-minute effort into a 50-minute (or more) chore, complete with rounded-off, ruined, or snapped fasteners, e-z outs, heli-coil inserts, and more.........and that's just not right.
While the proper use of our various Anti-Seize products will prevent these nightmares from occurring in the future, you're stuck in the here-and-now, and the best way to handle these obstacles is to have the proper tools at the stand-by; and in the case of fastener seizure, the proper "tool" is a can or two of our SUPER PENETRATING LUBRICANTS at the ready; a couple of squirts, a little bit of time-----perhaps some heat for those really nasty situations----and you're on your way again, hopefully not too much worse for the experience.....
Great for use on all fasteners, fork tube cap bolts, intake and exhaust manifolds bolts, studs, and nuts, lock cylinder tumblers, or anywhere an un-cooperative fastener can be found. Can even be used to help un-seize frozen engines!
Be aware that these products are not your typical, garden-variety, run-of-the-mill "retail" type products; these are designed an used as industrial- and military-strength products, meaning they have special formulations that include a dollop more of the "good stuff" within them to solve the toughest seizure problems imaginable (the "good stuff" ingredients cost more, and it is those compounds that are left out of or reduced in concentration in "retail" level consumer products).
NOTE: the following product(s) can only be shipped via ground transport (which thus eliminates the postal Priority Mail, postal Express Mail, or private carrier Expedited levels of service for this item) and cannot (and will not----don't even ask!) be shipped outside of the continental USA. Additionally, there may be a per-package weight or quantity restriction, and thus multiple-unit orders of this product may have to be shipped in separate packages and will incur additional shipping charges.
HCP10331 Aftermarket standard-duty PENETRATING LUBRICANT, in a generous 16-ounce aerosol can. Oil-based lubricant penetrates down into spaces of one-millionth of an inch to handle the most reluctant seizures. Actually dissolves the rust and corrosion that causes the seizure; lubricates and displaces moisture to prevent rust re-formation. This product is what we use and recommend for freeing stuck fork tube cap bolts and other such challenging fasteners.
$ 24.95
HCP11974 Aftermarket super-duty PENETRATING LUBRICANT, in a generous 13-ounce aerosol can. Same as our standard-duty formula above, but also includes graphite to not only enhance and speed up the penetrant action, but also gets down into the pores of the metal for the greatest possible lubrication possible. The cat's-meow of penetrating fluids, can even be used to un-seize frozen engines or as an engine assembly lube! This fluid is also a great choice for use as a drive cable lubricant.
$ 26.95
HCP10333 Aftermarket extreme-duty PENETRATING LUBRICANT, in a generous 16-ounce aerosol can. Same as our standard-duty formula above, but also includes liquid silicone to enhance and speed up the penetrant action. This product is also an exceptional choice for use as a control-cable lubricant.
$ 27.95
Assembly Fluids and Lubricants:
NOTE: the following product(s) can only be shipped via ground transport (which thus eliminates the postal Priority Mail, postal Express Mail, or private carrier Expedited levels of service for this item) and cannot (and will not----don't even ask!) be shipped outside of the continental USA. Additionally, there may be a per-package weight or quantity restriction, and thus multiple-unit orders of this product may have to be shipped in separate packages and will incur additional shipping charges.
HCP20860 Aftermarket industrial-strength ASSEMBLY LUBE, in a standard 12-ounce aerosol can. Heavy-duty formula includes graphite to not only enhance and speed up the penetrant action, but also gets down into the pores of the metal for the greatest possible lubrication possible. Won't wash away, protect against rust and corrosion, stable from 0-degrees up to 250-F. This fluid is also a great choice for use as a drive cable lubricant.
$ 21.95
HCP20862 Aftermarket super-duty ASSEMBLY LUBE, in a generous 10-ounce aerosol can. The cat's-meow of lubricants, infused with pure moly disulfide, it goes on wet and then dries in 1-2 hours to a super-slick, high-pressure, hi-temp, bearing-like finish which provides the ultimate level of protection. Prevents rust and corrosion, won't wash off, throw off, and won't attract dust or dirt. Surfaces must be clean and dry of previous oils, etc. before application. Can even be used as an engine, tranny, and drivetrain assembly lube!
$ 24.95
HCP20863 Aftermarket super-duty GRAPHITE LUBE, in a generous 10-ounce aerosol can. The 800-pound gorilla of lubricants, it's infused with pure graphite, goes on wet, and then dries in 10 minutes to a super-slick, high-pressure, bearing-like finish which provides the ultimate level of protection. Prevents rust, won't wash off, throw off, and won't attract dust or dirt. Surfaces must be clean and dry of previous oils, etc. before application. Can be used as an engine assembly lube, bearing or bushing pre-lube, great for lock cylinders, and all metallic sliding surfaces. Use where dusty or dirty conditions render oil-based lubricants ineffective or undesirable.
$ 21.95
Engine Cleaners and De-greasers:
NOTE: the following product(s) can only be shipped via ground transport (which thus eliminates the postal Priority Mail, postal Express Mail, or private carrier Expedited levels of service for this item) and cannot (and will not----don't even ask!) be shipped outside of the continental USA. Additionally, there may be a per-package weight or quantity restriction, and thus multiple-unit orders of this product may have to be shipped in separate packages and will incur additional shipping charges.
HCP12352 Aftermarket water-soluble (rinse-off) AEROSOL ENGINE DEGREASER and CLEANER, in a handy 13-ounce aerosol can. Each:
$ 24.95
HCP12354 Aftermarket water-soluble (rinse-off) ENGINE DEGREASER and CLEANER, in a 16-ounce non-aerosol can. Best to transfer into an old windex spray bottle (etc.) and use with a spray nozzle. Each:
$ 21.95